Block teach-in mode immediately:
Tap an already taught-in radio button (not
central control button) 3 times briefly plus 1
time long (>2 seconds). Locking is signaled
by briefly switching the lamp on and off
twice.
Unlock teaching mode:
Tap an already taught-in radio button (not
central control button) 4 times briefly plus
1 time long (>2 seconds). The readiness for
programming is signaled by briefly switching
the lamp on and off.
Delete memory content completely (restore
delivery status):
1. Switch the supply voltage off and on.
2. Tap an already taught-in radio button
(not central control button) 8 times
briefly plus 1 time long (>2 seconds).
Deletion is signaled by briefly switching
the lamp on and off.
3. Start again to 'Teach in wireless push-
button'.
Completely delete the memory content wit-
hout a radio button (restore delivery status):
Switch on the supply voltage, lamp switches
on with maximum brightness and dims to
minimum brightness, then switch off the
supply voltage. Repeat this a total of 8
times, at the end of the 8th time the lamp
turns off and the memory has been cleared.
Direction pushbutton: 'Switch on and dim
up' on one side and 'Switch off and dim down'
on the other side.
Universal pushbutton: Short control com-
mands switch on/off, permanent control
changes the brightness up to the maximum
value. An interruption of the control changes
the dimming direction.
Central control button::
Central ON: short click switches on with
memory value.
In motion detector mode, you can switch to
permanent ON by pressing >3 seconds (ack-
nowledgment by flashing of the lamp).
Central OFF: Short click switches off.
In motion detector mode, you can switch to
permanent OFF by pressing >3 seconds
(acknowledgment by flashing of the lamp).
A short click on the central control button,
direction button or universal button ends
the stuck mode, i.e. the motion detector is
evaluated again.
Rotary switch: Press or turn to switch on.
Turn right to dim up and turn left to dim
down. Press to turn off.
White tone and intensity double rocker
switch: The left rocker changes the color
temperature, top press cold white and
bottom press warm white. The right rocker
changes the intensity, brighter at the top
and darker at the bottom.
Children´s room function (universal button or
direction button on the switch-on side):
When switching on by pressing the button for
a longer period of time, after approx. 1 second
it is switched on with the lowest brightness
and, as long as the button is pressed, it is
slowly dimmed up without changing the last
saved brightness level.
Semi-automatic motion detection with
taught-in wireless motion sensor FB55B,
FBH55SB (factory setting):
After switching on with a button, an off-delay
time of 2 minutes is started, within this
time, a follow-up switch is made if there is
movement. If no more movement is detected,
it switches off automatically after 2 minutes.
The actuator then reacts to movement for a
further 2 minutes and switches back on
automatically if necessary. After the time
has elapsed, the button must be used to
switch it on again. It can be switched off at
any time with a button, movement is then
no longer evaluated.
Fully automatic motion detection with
taught-in wireless motion sensor FB55B,
FBH55SB:
If the actuator should also switch on auto-
matically when there is movement, e.g. in
rooms without daylight, the jumper in the
movement sensor must be switched to 'ac-
tive'. If no more movement is detected, it is
switched off automatically after the release
delay time of 2 minutes has expired. It can
be switched on and off at any time with a
button, and it is automatically switched on
again when there is movement. With control
via the GFVS software, light scenes can be
set and called up.
Switch confirmation telegrams on or off:
1. Switch the supply voltage off and on.
2. Tap an already taught-in radio button (not
central control button) 7 times briefly plus
1 time long (>2 seconds). On is signaled by
briefly switching the lamp on and off twice.
The lamp briefly switches on and off to
signal off.
Manuals and documents in further
languages
http://eltako.com/redirect/FDG62-230V
1. App 2. 3.
www.
Eltako GmbH
D-70736 Fellbach
Technical Support English:
+49 711 94350025
technical-support@eltako.de
eltako.com
27/2022 Subject to change without notice.
Must be kept for later use!
We recommend the housing for
operatinginstructions GBA14.
Frequency 868.3 MHz
Transmit power max. 10mW
Hereby, Eltako GmbH declares that the radio
equipment type FDG62-230V is in com-
pliance with Directive 2014/53/EU.
The full text of the EU declaration of
conformity is available at the following
internet address: eltako.com
