InSight Desktop only runs under Windows XP and requires
Java 1.5V6 or later.
1. Insert InSight Desktop (ISD) CD into CD-ROM drive.
If Setup doesn’t start automatically, browse to emberSetup.exe
in the CD’s root directory and run it.
2. Follow on-screen instructions to install ISD.
3.Installing InSight Desktop
Once you have connected the hardware and installed the software,
run ISD’s Setup Wizard to verify the installation.
1. Launch ISD: Start | All Programs | Ember | InSight Desktop | InSight Desktop.
2. Enter the Ember Support Portal username obtained from Ember Support
and click Save username and continue. If you don’t have a username,
click Continue without registration. Once you have a username, you can
register with Help | Register.
3. Launch ISD’s First-Time Setup Wizard: Click Start First-time Setup button
or select Help | First-time setup wizard.
4. Click Next and follow the on-screen instructions.
The First-Time Setup Wizard will search your network for attached ISA3s.
When done, you will have connected the ISA3s and loaded application
images on them. You are now ready to capture network traffic from the ISA3s.
CONGRATULATIONS!
5. Click Finish.
You must be a registered user of the Ember Support Portal to obtain support, download
the latest Ember Development Software, and receive automatic updates of ISD. To
create an account, go to http://www.ember.com/support_index.html and follow the
instructions there before continuing. You will need to provide the Ember Software Serial
Number on the Hardware Identification List attached to this guide.
A. IAR Workbench
1. Insert IAR Embedded Workbench CD into CD-ROM drive.
If Setup doesn’t start automatically, browse to autorun.exe in the CD’s root
directory, and run it.
2. Follow the on-screen instructions to install IAR Embedded Workbench.
Licenses and support are provided separately and can be obtained from
IAR Systems at http://www.iar.com.
By default, ISA3s are configured to acquire IP addresses using DHCP.
If your network environment instead requires use of static IP addresses,
configure each ISA3 as follows.
1. Browse to Utilities folder of ISD CD and run ISA3_Utilities.exe.
2. Disconnect one ISA3 entirely from PoE Switch.
3. Connect one end of USB Cable to ISA3.
4. Connect other end of USB Cable to the PC.
5. Open a command window and change directory to:
C:\Program Files\Ember\ISA3 Utilities\bin (the default).
6. Run em3xx_isa.exe with these parameters to configure static IP settings:
em3xx_isa.exe --admin "ip static IPADDR NETMASK GATEWAY"
Replace IPADDR, NETMASK, and GATEWAY with your desired settings.
Example
The following command line changes settings to a static IP address of
192.168.1.100 with a netmask of 255.255.255.0 and a gateway of 192.168.1.1.
C:\Program Files\Ember\ISA3 Utilities>
em3xx_isa.exe --admin "ip static 192.168.1.100 255.255.255.0 192.168.1.1"
Result
Success: ip: (after reboot) Static 192.168.1.100 255.255.255.0 192.168.1.1
7. Run em3xx_isa.exe one more time with these parameters to disable DHCP:
C:\Program Files\Ember\ISA3 Utilities>em3xx_isa.exe --admin "ip dhcp off"
Result
Success: ip: (after reboot) DHCP off
8. Unplug ISA3 from USB Cable, and reconnect ISA3 to PoE Switch
per “Connecting the Hardware” section.
9. Repeat steps 2–8 for the two other ISA3s.
4.Configuring Static IP Addresses (optional)
5.Running ISD’s First-Time Setup Wizard to Verify Installation
6.Doing Custom Development
7. For More Information
B. EmberZNet
1. Go to EmberZNet PRO for EM35x: http://portal.ember.com/em35x.
2. Log in with your username and password.
3. Follow the instructions to download and install the latest versions of all
Ember Development Software for your EM35x Development Kit.
If you have any installation issues, refer to the EM35x User Guide (120-4030-000).
You can also use the Ember Developer Portal at http://portal.ember.com.
Copyright © 2009 Ember Corporation. All rights reserved. Ember is a registered trademark and the
Ember logo and InSight are trademarks of Ember Corporation. All other trademarks are the property
of their respective holders.
USB Cable
Place Hardware Identification List here
EM35x Development Kit
Quick Start Guide
Thank you for purchasing
the Ember EM35x Development Kit.
Please read this Quick Start Guide to get up and running
quickly. If you have any issues, refer to the “For More
Information” section at the end of this guide.
