Emerson Rosemount 356 User manual

Reference Manual
00809-0100-4856 Rev AE
February 2020
Rosemount 356
Rosemount 356 Nuclear Connector

Rosemount 356
Reference Manual
00809-0100-4856 Rev AE
February 2020
ii
This page intentionally left blank

Reference Manual
00809-0100-4856 Rev AE
February 2020
Rosemount 356
Title Page iii
Rosemount 356 Nuclear Connector
NOTICE
Read this manual before working with the product. For personal and system
safety, and for optimum performance, make sure you thoroughly understand the
contents of this manual before installing, using or maintaining this product.
For Assistance:
Within the United States, contact Rosemount Nuclear at
1-952-949-5200.
Outside the United States, contact the nearest Rosemount representative.
Customer Feedback:
Your feedback is important to us, please send comments or suggestions to:
[e-mail]

Rosemount 356
Reference Manual
00809-0100-4856 Rev AE
February 2020
iv Title Page
Rosemount Nuclear Warranty and Limitations of
Remedy
The warranty and limitations of remedy applicable to this Rosemount equipment are as stated on the
reverse side of the current Rosemount quotation and customer acknowledgment forms.
RETURN OF MATERIAL
Authorization for return is required from Rosemount Nuclear prior to shipment. Contact Rosemount Nuclear
(1-952-949-5200) for details on obtaining Return Material Authorization (RMA). Rosemount Nuclear
Instruments will not accept any returned material without a Return Material Authorization. Material
returned without authorization is subject to return to customer.
Material returned for repair, whether in or out of warranty, should be shipped prepaid to:
Rosemount Nuclear
8200 Market Boulevard
Chanhassen, MN 55317
USA
IMPORTANT
Rosemount 356 Nuclear Connector has been tested for Nuclear Class 1E usage according to the standards
shown below:
•KTA 3505-2005
Rosemount 356 Connectors are manufactured under a quality system that meets the requirements of ISO
9001, KTA 1401, KTA 3507 and the applicable portions of IAEA-50-C-Q. During qualification testing,
interfaces were defined between transmitter/connector and the surrounding environment that are essential to
meeting requirements of the qualification standards listed above.
In order to maintain the qualified status of the transmitter/connector system, the essential environmental
interfaces must not be compromised. Performance of any operations on the connector other than those
specifically authorized in this manual has the potential for compromising an essential environmental interface.
Where the manual uses the terms requirement, mandatory, must or required, the instructions so
referenced must be carefully followed. Rosemount Nuclear expressly disclaims all responsibility and
liability for connectors for which the foregoing has not been complied with by the user.

Reference Manual
00809-0100-4856 Rev AE
February 2020
Rosemount 356
Title Page v
Revision Status
Changes from March 2013 (Rev AD) to February 2020 (Rev AE)
Page
(Rev AD)
Page
(Rev AE)
Changes
Cover,
throughout
Cover,
throughout
Change revision date from March 2013 to February 2020; change revision from
AD to AE.
Cover,
throughout
Cover,
throughout
Replace Emerson logo.
Throughout Throughout
Replace Rosemount Nuclear Instruments, Inc. with Rosemount Nuclear per
current practice.
Throughout
Throughout
Replace reference to Loctite PST 580 with Loctite® 580™.
TOC-2,
1-2, 2-8
TOC-2,
1-2, 2-8
Add “This page intentionally left blank” for clarity.
2-2
2-2
Add “as indicated in the 356 Product Data Sheet” for available options.
2-2
2-2
Remove reference to 4-wire configuration.
2-3
2-3
Replace figure 2-1 with better resolution for clarity.
2-3
2-3
Fix typos in “Customer Installed Instrument Side Connector”.
2-4 2-4
Add figure 2-4a for current configuration with footnote of (As of February 2020)
and amended figure 2-4 to be figure 2-4b, Former/Original Configuration with
footnote (Up to February 2020).
2-5
2-5
Fix typo in ‘TEST’ terminal.
2-7
2-7
Add border to figure 2-7.
3-2
3-2
Update figures 3-2 and 3-3 description to remove material reference.
3-3
3-3
Add “Original” to figures 3-4 and 3-5 and footnote of (Up to February 2020).
A-2
A-2
Amend General Considerations.
NOTE
The above Revision Status list summarizes the changes made. Please refer to both manuals for complete
comparison details.

Reference Manual
00809-0100-4856 Rev AE
February 2020
Rosemount 356
Contents TOC-1
Table of Contents
SECTION 1
Introduction
Using this Manual........................................................................1-1
SECTION 2
Installation of Instrument
Side onto Device
Overview .....................................................................................2-1
Safety Messages
.........................................................................2-1
General Considerations
..............................................................2-2
Electrical Considerations
.............................................................2-2
Polarity ...........................................................................2-2
Factory Installed Instrument Side Connector.................2-3
Customer Installed Instrument Side Connector.............2-3
Mechanical Considerat
ions.........................................................2-4
Installation Procedure
.................................................................2-5
Preparation of the Instrument Side Connector...............2-5
Installation of the Instrument Side onto 3152
Pressure Transmitter......................................................2-6
Electrical Connection to 3152 Pressure
Transmitter.....................................................................2-7
SECTION 3
Installation of Field Side
onto Instrument Side
Overview .....................................................................................3-1
Safety Messages
.........................................................................3-1
General Considerations
..............................................................3-1
Mechanical Considerations
.........................................................3-1
Installation Procedure
.................................................................3-4
SECTION 4
Maintenance
Overview .....................................................................................4-1
Safety Messages
.........................................................................4-1
General Considerations
..............................................................4-1
Maintenance
................................................................................ 4-2
APPENDIX A
Procedure for On-site
Assembly of Field Side
Connector
Overview .....................................................................................A-1
Safety Messages
.........................................................................A-1
General Considerations
..............................................................A-2
Field Side Kit Contents
................................................................A-2
Required Tools
for Assembly......................................................A-3
A
ssembly Procedures .................................................................A-3
Prepare Cable and Attach Crimp Contacts....................A-4
Install Cable Gland.........................................................A-6
Assemble Field Side of Connector.................................A-8
Post
-Assembly Tests ................................................................A-11

Rosemount 356
Reference Manual
00809-0100-4856 Rev AE
February 2020
TOC-2
This page intentionally left blank

Reference Manual
00809-0100-4856 Rev AE
February 2020
Rosemount 356
SECTION 1: INTRODUCTION
USING THIS MANUAL
This manual is designed to assist in installing, operating and
maintaining the Rosemount 356 Nuclear Connector. The manual is
organized into the following sections:
Section 2: Installation of Instrument Side onto Device
Provides mechanical and electrical installation considerations of
the Instrument Side portion of the connector.
Section 3: Installation of Field Side onto Instrument Side
Provides mechanical and electrical installation considerations of
the Field Side portion of the connector.
Section 4: Maintenance
Provides basic hardware maintenance considerations for the 356
Connector.
Appendix A: Procedure for On-site Assembly of Field Side
Connector
Provides instructions for assembling the field side portion of the
connector on-site.
NOTE
Refer to Rosemount Qualification/Test Reports and Product Data
Sheet
s for details on testing, performance specifications and
dimensional drawings.

Rosemount 356
Reference Manual
00809-0100-4856 Rev AE
February 2020
1-2
This page intentionally left blank

Reference Manual
00809-0100-4856 Rev AE
February 2020
Rosemount 356
SECTION 2: INSTALLATION OF INSTRUMENT SIDE ONTO
DEVICE
Overview....................................................................................page 2-1
Safety Messages.......................................................................page 2-1
General Considerations...........................................................page 2-2
Electrical Considerations ........................................................page 2-2
Mechanical Considerations.....................................................page 2-4
Installation Procedure..............................................................page 2-5
SAFETY MESSAGES
Procedures and instructions in this section may require special
precautions to ensure the safety of the personnel performing the
operation. Refer to the following safety messages before performing
an operation preceded by this symbol.
Warnings
WARNING
Electrical shock can result in death or injury.
•Avoid contact with the connector leads and device terminals
WARNING
When installing the instrument side of the connector onto the
housing of the device, take care to prevent the lead wires from
becoming twisted or from being cut by any potential sharp edges
inside the electronics housing. The same care must be taken when
removing the connector from the device.
OVERVIEW
This section contains the following installation considerations:
•General Considerations
•Electrical Considerations
oPolarity
oFactory Installed Instrument Side Connector
oCustomer Installed Instrument Side Connector
•Mechanical Considerations
•Installation Procedure
oPreparation of the Instrument Side Connector
oInstallation of the Instrument Side onto 3152 Pressure
Transmitter
oElectrical Connection to 3152 Pressure Transmitter