Emerson Sensi Touch Wi-Fi Thermostat User manual

1
Installation
Touch Wi-Fi
Thermostat

2
Table of contents
COMPATIBILITY......................................................... 4
WHAT’S IN THE BOX...............................................6
WHAT YOU’LL NEED.................................................7
BEFORE YOU BEGIN...............................................8
INSTALLATION OVERVIEW.................................10
WARNINGS................................................................11

3
Need some help?
Visit sensicomfort.com/support for around-the-
clock access to support articles, instructional
downloads and comprehensive support videos.
Our highly-trained Sensi Support Team is available
seven days a week.
1.888.605.7131
[e-mail]
You’re just a few steps
away from complete
comfort control.
Never installed a thermostat before? We’ve got
you covered. Sensi™Touch Wi-Fi®Thermostat was
designed for a quick and easy DIY installation. The
Sensi app provides step-by-step instructions and
helpful videos to get you up and running in no time.

4
MOBILE DEVICE COMPATIBILITY
SMART HOME PLATFORM COMPATIBILITY
OPERATING SYSTEM COMPATIBILITY
iOS 10.0 or later Yes
Android Yes
Amazon Fire Yes
OPERATING SYSTEM COMPATIBILITY
Wink Yes
Amazon Alexa Yes
Apple HomeKit Yes, but requires a
common wire (c-wire)
Compatibility
Not only does Sensi work with the HVAC equipment
in most homes, but it also works with most mobile
devices and smart home platforms.
Check out the information below, to make sure
Sensi thermostat will work for you:

5
SYSTEM TYPE COMPATIBILITY MODIFICATIONS
Conventional heating
and cooling
•Gas furnace
•Air conditioner
•Electric furnace
•Boiler
Yes Requires a
common wire
(c-wire)
Heat only
•Gas furnace
•Electric furnace
•Boiler
Yes Requires a
common wire
(c-wire)
Cool only
• Air conditioner Yes Requires a common wire
(c-wire)
Heat pump Yes Requires a
common wire
(c-wire)
Communicating
proprietary
systems
No Needs standard
HVAC wiring
Line voltage No Requires
low voltage
(20-30VAC)
Millivolt systems No Requires
20-30VAC
Remote sensors,
whole home
humidifiers/
dehumidifiers
No Control of these
accessories is
not currently
supported
HVAC SYSTEM COMPATIBILITY

6
What’s in the box?
•Sensi Thermostat
•Screws and Anchors
•Wire Labels
•Sensi Password
For Android: Found on the back of the welcome guide.
For iOS: Your Sensi HomeKit Code will display on
your thermostat during the connection process.
XXX-XX-XXX

7
Here’s what you’ll need.
Things you’ll definitely need:
•Small Phillips Screwdriver
•Medium Phillips Screwdriver
•Compatible iOS or Android with the Sensi
App Installed
•Your Email Address
•Your Wi-Fi Network Name (SSID) and Password
Things you might need:
•Needle-Nose Pliers
•Drill with 3/16" Bit
•Wire Stripper
•Sensi Thermostat
•Screws and Anchors
•Wire Labels
•Sensi Password
For Android: Found on the back of the welcome guide.
For iOS: Your Sensi HomeKit Code will display on
your thermostat during the connection process.

88

99
Download the Sensi app
before you begin.
This document is not meant to be used
independently or to replace the step-by-step
installation procedure found only in the Sensi app.
The app is required for installation to ensure proper
configuration and enable Wi-Fi control of your
thermostat.
The free Sensi mobile app is available on the App
Store™and Google Play™
. Simply search for “Sensi”
and download to your device to get started.
All system types require a common wire (c-wire).

10
Installation Overview
CREATE YOUR ACCOUNT.
Open the Sensi app on your device and follow
the prompts to create an account, using a valid
email address.
Your Sensi account can only be linked to one
email address, but you can share your account
information across devices so your whole family can
have access.
INSTALL YOUR THERMOSTAT.
The Sensi app will walk you through removing your
old thermostat from the wall, labeling your existing
wires and installing your new Sensi thermostat.
CONNECT TO WIFI.
After installation the app will walk you through
connecting your new thermostat to your home
Wi-Fi network. Remember to have your Wi-Fi
network name, password and Sensi
password ready.
REGISTER YOUR THERMOSTAT.
Finally, the app will walk you through registration so
you can start controlling your home comfort.
Anytime. Anywhere.

11
Warnings
INSTALLER INFORMATION
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
BEFORE INSTALLING OR OPERATING THIS CONTROL COULD
CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE.
WARNING: OUT OF PHASE TRANSFORMERS
On two transformer systems, the transformers MUST be
in phase. Measure the voltage across RC and RH. If more
than 12 Volts AC is present between RC and RH, then the
transformers are NOT in phase.
To correct this condition, reverse the secondary low
voltage connections at either the Heating or Cooling
transformer.
VOLTAGE REQUIREMENTS
Do not use on circuits exceeding specified voltage. Higher
voltage will damage control and could cause shock or
fire hazard.
Thermostat installation and all components of the control system
shall conform to Class II circuits per the NEC code.

12
ATTENTION: MERCURY NOTICE
This product does not contain mercury. However,
this product may replace a product that contains mercury.
Mercury and products containing mercury must not be
discarded in household trash. Refer to thermostat-recycle.
org for location to send product containing mercury.
CAUTION: E5 Alert
If “Call For Service” is displayed on your Sensi thermostat,
and E4 or E5 appears where the room temperature
should be displayed or the backlight is flashing, please
call our support team immediately at 888.605.7131
FOR CALIFORNIA RESIDENTS: WARNING:
This product contains a chemical known to the state of
California to cause cancer and birth defects and other
reproductive harm.
To prevent electrical shock and/or equipment damage,
disconnect electric power to system at main circuit breaker
box until installation is complete.
www.sensicomfort.com
The Emerson logo is a trademark and service mark and the
Sensi logo is a trademark of Emerson Electric Co.

13
Installation
Thermostat
Wi-Fi Tactile

14
Table des matières
COMPATIBILITÉ....................................................... 16
CONTENU DE LA BOÎTE......................................18
CE DONT VOUS AVEZ BESOIN......................... 19
AVANT DE COMMENCER......................................21
APERÇU DE L’INSTALLATION............................22
AVERTISSEMENTS..................................................23

15
Besoin d’aide?
Visitez sensicomfort.com/support pour accéder
24heures sur24 à des articles de soutien, à des
téléchargements didactiques et à des vidéos de
soutien détaillées. Notre équipe de soutien Sensi
hautement qualifiée est disponible sept jours
parsemaine.
1888605-7131
[e-mail]
Vous n’êtes qu’à
quelques pas d’une
maîtrise complète
duconfort.
Vous n’avez jamais installé un thermostat? Nous
sommes là pour vous. Le thermostat tactile Sensi™
Wi-Fi®a été conçu pour une installation rapide et
facile, réalisée par vous. L’application Sensi offre
des directives pas à pas et des vidéos utiles pour
vous aider à mettre rapidement le thermostat
en fonction.

16
COMPATIBILITÉ AUX DISPOSITIFS MOBILES
COMPATIBILITÉ AUX PLATEFORMES
D’HABITATIONINTELLIGENTE
SYSTÈME D’EXPLOITATION COMPATIBILITÉ
iOS 10.0 ou plus récent. Oui
Android Oui
Amazon Fire Oui
SYSTÈME D’EXPLOITATION COMPATIBILITÉ
Wink Oui
Amazon Alexa Oui
Apple HomeKit Oui, mais requiert un
fil commun
Compatibilité
Il fonctionne non seulement avec l’équipement CVC
de la plupart des maisons, mais également avec la
plupart des plate-formes d’appareils mobiles et de
téléphones intelligents.
Consultez les renseignements ci-dessous pour
vous assurer que le thermostat convient à
votreéquipement:

17
TYPE DE SYSTÈME COMPATIBILITÉ MODIFICATIONS
Chauffage et
climatisation classiques
•Générateur de
chaleur au gaz
•Climatiseur
•Générateur de
chaleur électrique
•Chaudière
Oui Requiert un
fil commun
Chauffage seulement
•Générateur de
chaleur au gaz
•Générateur de
chaleur électrique
•Chaudière
Oui Requiert un
fil commun
Climatisation
seulement
• Climatiseur
Oui Requiert un
fil commun
Thermopompe Oui Requiert un
fil commun
Systèmes
propriétaires
de communication
Non Nécessite un
câblage CVC
standard
Tension de ligne Non Requiert une basse
tension
(20-30Vc.a.)
Systèmes millivolts Non Requiert
20-30Vc.a.
Capteur à distance,
humidificateurs/
déshumidificateurs
centralisés
Non La commande de
ces accessoires
n’est actuellement
pas prise en charge
COMPATIBILITÉ AUX SYSTÈMES CVC

18
XXX-XX-XXX
Contenu de la boîte
•Thermostat Sensi
•Vis et ancrages
•Étiquettes de fils
•Code de sécurité Sensi
Pour Android :  l’endos du Guide de bienvenue.
Pour IOS : Votre code Sensi HomeKit s’affichera sur
votre thermostat pendant le processus de connexion.

19
Voici ce dont vous
aurezbesoin.
Ce dont vous avez
vraimentbesoin:
•Petit tournevis cruciforme
•Tournevis cruciforme moyen
•Appareil compatible iOS, Android ou
Amazon avec l’application Sensi
•Votre adresse de courriel
•Le nom (SSID) et le mot de passe de votre réseau Wi-Fi
Ce dont vous aurez
peut-êtrebesoin:
•Pince à bec effilé
•Perceuse avec mèche de 3/16po
•Outil à dénuder

20