Emos P5630S User manual

2101900003_31-P5630S_00_01_WEB 85 × 95 mm
P5630S
GB Thermostatic Radiator Valve
CZ Termostatická hlavice
SK Termostatická hlavica
PL Głowica termostatyczna
HU Termosztatikus radiátorszelep
SI Termostatska glava
RS|HR|BA|ME Termostatska glava
DE Thermostatkopf
UA Головка термостату
RO|MD Cap termostatic
LT Termostatinis radiatoriaus vožtuvas
LV Termostatisks radiatora vārsts
EE Termostaatiline radiaatoriklep
BG Термостатичен радиаторен клапан
FR Tête thermostatique
IT Comando termostatico
ES Cabezal termostático
NL Thermostatische kop
www.emos.eu

2
A
RA Adapter
RAV Adapter
RAVL Adapter

3
B
2
5
3
6
1
4

4
C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

5
1 2

6
3 4

7
5 6

8
7

9
GB | Thermostatic Radiator Valve
Specications
Temperature control range: 5 °C – 35 °C, 0.5 °C resolution
Range of displayed temperature: 1 °C – 70 °C, 0.5 °C resolution
Power supply: 2× 1.5 V AA
Maximum current draw: 90 mA
Maximum valve lift: 4.5 mm
Mounting dimensions of the head: M30 × 1.5
Operating temperature: -10 °C to 60 °C
Installation
1. The head is designed for all types of commonly available radiator valves
without the need to interrupt heat circulation. If the thermostatic head is
not compatible, proceed in accordance with information provided in the
Compatibility section.
2. Place batteries into the head before installing. Remove the old thermostatic
head by loosening the nut on the radiator head. Fit the head on the front and
manually tighten the nut.
Note:
• The head support must connect in the middle to the support on the head.
• The head must not be compressed or wedged.
• Make sure the screen is visible and legible in the mounted position.
Compatibility (see g. A)
The head may not be compatible with certain radiator heads.
Please compare your head with information provided by the manufacturer and
use a suitable adapter if needed.
Enclosed adapters: Danfoss RA, RAV, RAVL
Mount the adapter onto the head and turn it until it clicks in place.
Fasten the adapter with a screw, if the adapter is designed for it.

10
Inserting/Changing the Batteries (see g. B)
1. Grab a hold of the square section of the head located below the thread.
Turn the square section clockwise. You should hear the head‘s lock release
after turning.
2. Slide the inner core of the head from the housing.
3. Replace the batteries. Make sure to observe the correct polarity.
4. Find the arrow icon on the housing and the slide slot on the inner core.
5. Slide the core back into the housing.
6. Once the core is all the way in, grab a hold of the square bottom portion
of the head located below the thread and turn the inner core of the head
counter-clockwise. You should hear the head‘s lock close after turning.
Description of the Screen of the Thermostatic Head (see g. C)
1 – Low battery indicator .
Starts ashing once the batteries are nearly depleted.
2 – Indication of connection status to Zigbee gateway .
Indicator on – not connected. Indicator o – connected.
3 – Connection signal strength icon .
4 – Weekly mode icon .
Indicator on – the mode is active. Indicator o – the mode is inactive.
5 – Holiday mode icon .
Indicator on – the mode is active. Indicator o – the mode is inactive.
6 – Manual mode icon .
Indicator on – the mode is active. Indicator o – the mode is inactive.
7 – If the icon is lit up, the screen shows the current temperature in the room
.
8 – If lights up, the screen shows the temperature in the mode you
have set.
9 – The icon means the mode is active.
10 – Button for switching between weekly mode and manual mode .
11 – Conrmation button and button for turning Boost mode on or o .
12 – Button for switching between comfort and ECO mode.

11
13 – Icon for the open window function .
Indicator on – the head detects an open window and activates the function.
14 – Comfort or ECO mode active.
15 – Child lock icon .
16 – The icon indicates that you need to input the current time. The
icon indicates which time period of your weekly mode is currently
active.
17 – The number of the currently active time period in weekly mode .
18 – The icon indicates movement and status of the valve. If ashing, the
valve is closing/opening. If the valve is open, the icon stays lit. Once the
valve closes, the icon turns o.
Basic Settings
1. Mount the thermostatic head onto the radiator and insert the batteries.
2. Install the EMOS GoSmart app from Google Play/App Store onto your phone.
3. Connect the thermostatic head to your Zigbee gateway which is connected
to the EMOS GoSmart app in line with the following instructions.
Instructions for Connecting the Thermostatic Head to the Zigbee
Gateway
1. Click the „+ Add a New Device“ button in the settings of your Zigbee gateway
(see g. 1).
2. Find „Thermostat“ in the list of devices (see g. 2).
3. Simultaneously hold „Weekly/Manual“ and „Comfort/ECO“
buttons on the thermostatic head for 5 seconds (see the Description of the
Screen in the previous section of the manual). Conrm that the icon for
connection to the Zigbee gateway is ashing rapidly on the head (see g. 3).
4. The Zigbee gateway should detect the thermostatic head in a few moments.
Once it does, tap the „Done“ button (see g. 4).
5. After conrming the previous step, your phone will ask for conrmation
to add the thermostatic head to your GoSmart app. Continue by tapping
„Done“ (see g. 5).

12
6. Once you tap „Done“, you will be redirected to the main screen of your
GoSmart app, where the paired thermostatic head will already be available
(see g. 6).
Setting the Thermostatic Head
• The thermostatic head can be set using the EMOS GoSmart app.
• After opening the head on the „My Home“ page in EMOS GoSmart, you will
see the main screen of the thermostatic head (see g. 7).
• The main screen has 2 buttons: Mode and Settings.
• Tapping the Mode button allows you to select your mode of choice.
• Tapping the Settings button allows you to adjust the settings of individual
modes or activate the child lock.
Setting Temperature
The thermostatic head enables setting 4 dierent temperatures.
Manual temperature
• Temperature that can be adjusted manually either by hand (turning the head)
or in the app (using the + button on the main screen of the app).
Holiday temperature
• A constant temperature that can be set for a specic time period (1 day, 2
days, 5 days, 14 days etc.).
Comfort temperature
• A higher temperature (there are people in the room).
ECO temperature
• A lower temperature (temperature for the night or for when there are no
people in the room).
Temperature Programmes
The type of temperature programme can be selected on the Calendar Mode
page in EMOS GoSmart.
Types of temperature programmes:
• 5+2 (Mon -> Fri + Sat -> Sun)
• allows setting a xed temperature for the 5 workdays + 2 weekend days

13
• allows setting up to 6 time periods for both types of days
• 6+1 (Mon -> Sat + Sun)
• allows setting a xed temperature for 6 days (Monday to Saturday) +
Sunday
• allows setting up to 6 time periods for both types of days
• 7 days
• allows settings a xed temperature for 7 days
• allows setting up to 6 time periods for both types of days
The time periods are set on the „Weekly Programme Settings“ screen in EMOS
GoSmart. For each time period, set the temperature that the thermostatic head
should set from the time you specify in the time period settings. The temperature
you have set will remain active until the next time period.
Example: If you set time periods in line with the table below, room temperature will
be 16 °C from 3:00 to 6:00, then 20 °C from 6:00 to 9:00, 17 °C from 9:00 to 12:00,
19 °C from 12:00 to 14:00, 23 °C from 14:00 to 22:00 and 17 °C from 22:00 to 3:00.
1st time period 3:00 16 °C
2nd time period 6:00 20 °C
3rd time period 9:00 17 °C
4th time period 12:00 19 °C
5th time period 14:00 23 °C
6th time period 22:00 17 °C
Advanced Settings
Temperature Calibration
• The temperature sensor that detects ambient temperature is located in
the body of the thermostatic head which is mounted onto the radiator. The
measured temperature may therefore be higher than the temperature in
other parts of the room.

14
• Calibration can be set in EMOS GoSmart in a range of -9 °C to 9 °C with
1 °C resolution.
Open Window Function
• If the thermostatic head detects a sudden drop in temperature (e.g. when
the window or door is open), it closes the valve.
• Once the set time limit elapses or you close the window, the head automat-
ically reopens the valve.
Automatic Lock Function
• The function can be set in the EMOS GoSmart app.
• If the function is on, the screen automatically locks after 10 minutes without
any activity.
• You can unlock the screen again in EMOS GoSmart.
Setting Temperature Setting Limits for Manual Setting of the Thermostatic
Head
• Maximum temperature setting limit – species the maximum temperature
that can be set on the thermostatic head (max. 70 °C, 1 °C resolution)
• Minimum temperature setting limit – species the minimum temperature that
can be set on the thermostatic head (min. 1 °C, 1 °C resolution)
Adjusting the Valve
• The EMOS GoSmart app can be used to set the position of the valve in your
thermostatic head („Closed“, „Open“, „Normal“).
Displaying the Current Temperature in the Room
• The EMOS GoSmart app shows the current temperature in the room right on
the main page of the thermostatic head.
Child Lock
• You can activate/deactivate the child lock in the settings of the EMOS
GoSmart app.
• If the lock is active, the screen of the thermostatic head or the main page of
the head in the EMOS GoSmart app will show a lock icon.
Boost Mode
• The Boost mode can be used to heat up a room within a time you set.

15
• The time can be set in the EMOS GoSmart app in the Boost tab.
• The length of the heating interval can be set to 100–900 seconds.
Temperature Dierential Setting
• This feature can only be adjusted on the screen of the thermostatic head itself.
• The dierential can be set to 0.5 °C, 1 °C, 1.5 °C.
• The temperature dierential (hysteresis) is the dierence in temperature
required for switching the heating system on and o.
• For instance, if you set the temperature to 20 °C and the dierential to
1 °C, the thermostatic head activates heating as soon as room temperature
drops to 19 °C and switches heating o when temperature reaches 21 °C.
Controlling the Valve
• Can only be adjusted on the screen of the thermostatic head itself.
• These controls enable you to set how the valve of the thermostatic head
is to be controlled.
• Value = 0: control in accordance with the modes you have set; value = 1
automatic control based on current temperature.
• When automatic control is selected, the valve is controlled as follows:
• If the temperature you set is 2 °C higher than the temperature in the
room, the valve is 100 % open.
• If the temperature you set is 1 °C higher than the temperature in the
room, the valve is 75 % open.
• If the temperature you set is the same (±0.5 °C) as the temperature in
the room, the valve is 50 % open.
• If the temperature you set is 1 °C lower than the temperature in the
room, the valve is 25 % open.
• If the temperature you set is 2 °C lower than the temperature in the
room, the valve is closed.
Setting Modes and Functions on the Screen of the Thermostatic Head
• Once batteries are inserted, the thermostatic head turns on and the entire
screen lights up. Then the icon will light up. Pressing the
button allows you to set the current time. Set, in this order, hours, minutes

16
and day of the week (1 – Monday, 2 – Tuesday, 3 – Wednesday, 4 – Thursday,
5 – Friday, 6 – Saturday, 7 – Sunday). The time and day of the week is set
using the rotary wheel on the thermostatic head.
• Once you have set the time, conrm it by pressing the button.
• The letters Ad will appear after conrming. Continue by pressing the
button.
• The thermostatic head will start calibrating in two steps (the steps are
indicated by a number on the screen).
• Once calibration is complete, the screen will show the current temperature
in the room and you can begin setting individual functions and modes on
the thermostatic head.
1. Setting Weekly Mode
a. To set up weekly mode, hold the button for 5 seconds. This opens the
thermostatic head‘s settings.
b. Once you have completed the previous step, the icon will start
ashing. Press the button to conrm your selection of Weekly Mode.
c. Next, use the rotary wheel to select which Weekly Schedule you want to
set (5+2, 6+1, 7).
d. After you have selected the Weekly Schedule, use the rotary wheel to
choose the time for the 1st time period of the workday and the temperature
for the period. Conrm the selected time and temperature by pressing the
button.
e. Once you have set the rst 6 time periods of the workday, the number 1 will
appear on the top of the screen to indicate that you are now setting time
periods for a weekend day. Set the time and temperature in the same manner
as you did for the workdays.
f. After you have set all time periods, you can either go back to setting the
thermostatic head using the button or go to the main screen using the
button. If you conrm any action in the settings by pressing ,
the data is automatically saved.

17
g. If you have set up a Weekly Mode, you can activate it by short-pressing the
button. The mode is active when the and icons are lit up
on the screen.
2. Setting the Current Time
a. If you wish to adjust the time you have set when starting up the thermostatic
head, hold the button for 5 seconds. This opens the thermostatic
head‘s settings.
b. Select the time setting option by repeatedly pressing the button. Time
setting is selected once the icon starts ashing. Press to
conrm the selection of the setting.
c. Once you are in settings, set the time and the day of the week (1 – Monday, 2
– Tuesday, 3 – Wednesday, 4 – Thursday, 5 – Friday, 6 – Saturday, 7 – Sunday).
d. Conrm all steps by pressing the button. This will save the settings.
e. After you have set the time of choice, you can either go back to setting the
thermostatic head using the button or go to the main screen using
the button.
3. Setting Holiday Mode
a. To set up Holiday Mode, hold the button for 5 seconds. This opens the
thermostatic head‘s settings.
b. Select the Holiday Mode settings option by repeatedly pressing the
button. Holiday Mode settings are selected when the icon starts ashing.
Press to conrm the selection of the setting.
c. Once you are inside Holiday Mode settings, set, in this order, the temperature
you want to maintain during the mode and the duration of Holiday Mode.
Conrm each step by pressing the button.
d. Once you have conrmed your chosen Holiday Mode duration, the thermostat-
ic head navigates back to the main screen and Holiday Mode will be active.
4. Setting ECO Mode
a. To set up ECO Mode, hold the button for 5 seconds. This opens the
thermostatic head‘s settings.

18
b. Select the ECO Mode settings option by repeatedly pressing the button.
ECO Mode settings are selected when the icon starts ashing. Press
to conrm the selection of the setting.
c. Once you are inside ECO Mode settings, use the rotary wheel on the thermo-
static head to set the temperature and conrm by pressing the button.
d. Once you have conrmed your chosen ECO Mode temperature, the thermo-
static head navigates back to the main screen.
5. Setting Comfort Mode
a. To set up Comfort Mode, hold the button for 5 seconds. This opens the
thermostatic head‘s settings.
b. Select the Comfort Mode settings option by repeatedly pressing the
button. Comfort Mode settings are selected when the icon starts ashing.
Press to conrm the selection of the setting.
c. Once you are inside Comfort Mode settings, use the rotary wheel on the
thermostatic head to set the temperature and conrm by pressing the
button.
d. Once you have conrmed your chosen Comfort Mode temperature, the
thermostatic head navigates back to the main screen.
6. Setting Temperature Calibration
a. To set Temperature Calibration, hold the button for 5 seconds. This
opens the thermostatic head‘s settings.
b. To select Temperature Calibration, repeatedly press the button. Temper-
ature Calibration settings are selected when the icon starts ashing.
Press to conrm the selection of the setting.
c. Conrming the previous step takes you to the advanced settings of the
thermostatic head. There, Temperature Calibration is marked by the number
1 in the top right corner of the screen. Temperature calibration can be set to
between -9 °C and 9 °C. The value shown on the screen is based on current
temperature in the room.

19
d. Conrm temperature calibration by pressing . Conrming redirects you
to the next advanced setting (setting the Open Window function, marked by
the number 2 in the top right corner of the screen).
e. To go back to settings of the thermostatic head, press . To return to the
main screen, press .
7. Setting the Open Window Function
a. To set the Open Window function, hold the button for 5 seconds. This
opens the thermostatic head‘s settings.
b. To select the Open Window function, repeatedly press the button. Open
Window function settings are selected when the icon starts ashing.
Press to conrm the selection of the setting.
c. Conrming the previous step takes you to the advanced settings of the
thermostatic head. To navigate in the advanced settings, press .
There, the Open Window function is marked by the number 2 in the top
right corner of the screen.
d. Once 2 and the icon appear in the top right corner of the screen, you can
set the temperature at which the Open Window function should activate. You
can set the temperature to between 5 °C and 25 °C, or you can turn o the
function completely. If you wish to turn o the function, turn the wheel on the
thermostatic head counter-clockwise until two dashes appear on the screen.
e. To conrm your setting of the Open Window function, press the button.
Conrming redirects you to the next advanced setting (setting the Auto Lock
function, marked by the number 3 in the top right corner of the screen).
f. To go back to settings of the thermostatic head, press . To return to the
main screen, press .
8. Automatic Screen Lock Function
a. To set the Auto Lock function, hold the button for 5 seconds. This opens
the thermostatic head‘s settings.
b. To select the Auto Lock function, repeatedly press the button. The Auto
Lock function is selected when the icon starts ashing. Press
to conrm the selection of the setting.

20
c. Conrming the previous step takes you to the advanced settings of the
thermostatic head. To navigate in the advanced settings, press .
There, the Auto Lock function is marked by the number 3 in the top right
corner of the screen.
d. Once 3 and the icon appear in the top right corner of the screen, you
can use the rotary wheel on the thermostatic head to choose whether you
wish to turn the function on or o. 0 = function inactive. 1 = function active.
e. To conrm your setting of the Auto Lock function, press the button.
Conrming redirects you to the next advanced setting (Minimum Tempera-
ture Setting Limit settings, marked by the number 4 in the top right corner
of the screen).
f. To go back to settings of the thermostatic head, press . To return to the
main screen, press .
9. Setting the Minimum Temperature Setting Limit
a. To set the Minimum Temperature Setting Limit, hold the . button for 5
seconds. This opens the thermostatic head‘s settings.
b. To select the Minimum Temperature Setting Limit settings, repeatedly
press the . button. The Minimum Temperature Setting Limit option is
selected when the icon starts ashing. Press to conrm the
selection of the setting.
c. Conrming the previous step takes you to the advanced settings of the
thermostatic head. To navigate in the advanced settings, press . There,
Minimum Temperature Setting Limit settings are marked by the number 4 in
the top right corner of the screen.
d. Once the number 4 appears in the top right of the screen, you can use the
rotary wheel on the thermostatic head to set the Minimum Temperature
Setting Limit. The temperature can be set to between 1 °C and 15 °C.
e. To conrm your Minimum Temperature setting, press the button.
Conrming redirects you to the next advanced setting (Maximum Tempera-
ture Setting Limit settings, marked by the number 5 in the top right corner
of the screen).