Empire Comfort Systems DVCT30CBN95N-1 Planning guide

Page 1
DIRECT VENT
GAS FIREPLACE HEATER
FIREPLACE
INSERT MODELS
DVCT(30,35)CBN95(N,P)-1
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
This replace is design
certied in accordance
with American National
Standard/CSA Standard
ANSI Z21.88/CSA 2.33
and by Underwriters
Laboratories as a Direct
Vent Gas Fireplace
Heater and shall be
installed according to
these instructions.
GAS-FIRED
UL FILE NO. MH30033
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death or
property damage.
— Do not store or use gasoline or other
ammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier
from a neighbor’s phone. Follow the
gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the re department.
— Installation and service must be
performed by a qualied installer,
service agency or the gas supplier.
This appliance may be installed into a listed
wood-burning replace in an aftermarket,
permanently located, manufactured home
(USA only) or mobile home, where not
prohibited by state or local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certied kit is used.
HOT GLASS
DO NOT TOUCH
NEVER
WILL
CAUSE BURNS.
GLASS
UNTIL COOLED.
ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals.
DANGER
HOMEOWNER’S MANUAL
38101

38101-1-0318Page 2
TABLE OF CONTENTS
Combustible Material .................................................................................................................................. 2
Homeowner Reference Information ............................................................................................................ 2
Multifunction Remote Operating Instructions ......................................................................................... 3 - 9
Seasonal Shutdown .................................................................................................................................... 9
Intermittent Pilot Lighting Instructions ....................................................................................................... 10
Maintenance And Service .................................................................................................................. 11 - 12
Important Safety Information .................................................................................................................... 13
Safety Information For Users Of Propane Gas ......................................................................................... 14
Requirements For Massachusetts ............................................................................................................ 15
Warranty ................................................................................................................................................... 16
SECTION PAGE
COMBUSTIBLE MATERIAL
WARNING
Do not attach combustible material above your replace.
This is a re hazard. No greeting card, stockings or
ornamentation of any type should be placed on or attached
to the replace. This is a heating appliance. The ow of heat
can ignite combustibles.
Figure 1
GENERIC MODEL SHOWN
Television Considerations
Installing a television above a replace has become increasingly
popular; however, the areas above any replace gets hot and most
TV manufacturers recommend against placing their products near
a heat source.
If you install a television above this replace insert, Empire Comfort
Systems accepts no responsibility for damage or injuries. Follow
the television manufacturers installation instructions, including
any recommendations regarding proximity to heat sources.
If your have a TV above your replace turn off the replace and
let it cool completely before servicing or touching any buttons on
the TV.
We recommend that you record the following information about your replace.
Model Number: _____________________________ Date purchased: ________________________
Serial Number: _____________________________ Location of replace: _____________________
Dealer Name: ______________________________ Dealer Phone: _________________________
Notes: ______________________________________________________________________________
HOMEOWNER REFERENCE INFORMATION

38101-1-0318 Page 3
MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS
TECHNICAL DATA
Remote Control
Supply voltage 4.5 V (three 1.5 V
AAA batteries)
Ambient temperature ratings 0-50°C (32 - 122°F)
Radio frequency 315 MHz
NOTICE: The transmitter and receiver are radio frequency
devices. Placing the receiver in or near metal may severely reduce
the signal range.
WARNING
Turn “OFF” the main gas supply and electrical supply to
the appliance during installation and/or maintenance of the
receiver device.
WARNING
FIRE HAZARD.
Can cause severe injury or death. The receiver causes
ignition of the appliance. the appliance can turn on
suddenly. Keep away from the appliance burner when
operating the remote system or activating manual bypass
of the remote system.
CAUTION
PROPERTY DAMAGE HAZARD.
Excessive heat can cause property damage. The appliance
can stay lit for many hours. Turn off the appliance if it is
not going to be attended for any length of time. Always
place the transmitter where children can not reach it.
Figure 2
Figure 3
NOTICE: This control system includes a Battery Back-up pack
that allows the Fireplace to operate in the event of a power outage.
NOTICE: The Accent Light will not operate during a power outage.
NOTICE: Replace all Batteries at least once each year, preferably
before at the beginning of the season.
CAUTION
FIRE OR EXPLOSION HAZARD.
Can cause property damage, sever injury or death. Do not
attempt to take apart the gas control or to clean it. Improper
assembly and cleaning can cause unreliable operation.

38101-1-0318Page 4
MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS
Initializing the System
1. Install three AAA batteries into the battery bay located on the
base of the transmitter. See Figure 4.
Figure 4
2. Push the sync button to the right of the insert. See Figure 5.
Figure 5
3. With the batteries already installed in the transmitter, push the
ON button. See Figure 3. The receiver will “beep” four times
to indicate the transmitter’s command is accepted and sets
to the particular code of that transmitter. The system is now
initialized.
Temperature Indication Display °C or °F
With the system in the “OFF” position, press the Thermostat
Button and the Mode Button at the same time. Look at the LCD
screen on the transmitter to verify that a °C or °F is visible to the
right of the Room Temperature display. See Figures 6 and 7.
Figure 6
Figure 7
SYNC
BUTTON

38101-1-0318 Page 5
Turn On the Appliance
With the system OFF, press the ON/OFF Button on the Transmit-
ter. The Transmitter display will show some other active Icons on
the screen. At the same time the Receiver will activate the appli-
ance. A single “beep” from the Receiver will conrm reception of
the command.
Turn OFF the Appliance
With the system ON, press the ON/OFF Button on the Transmit-
ter. The Transmitter LCD display will only show the room tem-
perature. See Figure 8. At the same time the Receiver will turn
off the appliance. A single “beep” from the Receiver conrms
reception of the command.
Remote Control Display - Figure 8
Remote Flame Control
The Proame has six ame levels. With the system on, and the
ame level at the maximum in the appliance, pressing the Down
Arrow Button once will reduce the ame height by one step until
the ame is turned off.
The Up Arrow Button will increase the ame height each time it
is pressed. If the Up Arrow Button is pressed while the system is
on but the ame is off, the ame will come on in the high position.
See Figures 9 through 12. A single “beep” will conrm reception
of the command.
OFF
Flame Off - Figure 9
MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS
OFF
Flame Level 1 - Figure 10
OFF
Flame Level 5 - Figure 11
OFF
Flame Level Maximum - Figure 12.

38101-1-0318Page 6
MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room thermostat. The
thermostat can be set to a desired temperature to control the
comfort level in a room. To activate this function, press the
Thermostat Button (Figure 3). The LCD display on the Transmit-
ter will change to show that the room thermostat is “ON” and the
set temperature is now displayed. See Figure 13. To adjust the
set temperature, press the Up or Down Arrow Buttons until the
desired set temperature is displayed on the LCD screen of the
Transmitter. See Figure 14.
SET TEMPERATURE
ROOM TEMPER ATURE
Figure 13
Figure 14
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the ame height in ac-
cordance to the difference between the set point temperature
and the actual room temperatures. As the room temperature gets
closer to the set point the Smart Function will modulate the ame
down. To activate this function, press the Thermostat Button until
the word “SMART” appears to the right of the temperature bulb
graphic. See Figure 15. To adjust the set temperature, press the
Up or Down Arrow Buttons until the desired set temperature is
displayed on the LCD screen of the Transmitter. See Figure 16.
NOTICE: When Smart Thermostat is activated, manual ame
height adjustment is disabled.
Figure 15
Figure 16
Blower Control (Fan)
If the appliance is equipped with a hot air circulating fan, the
speed of the fan can be controlled by the Proame system. The
fan speed can be adjusted through six speeds. To activate this
function, use the Mode Button (Figure 3) to index the fan control
icon. See Figure 17. Use the Up/Down Arrow Buttons (Figure
56) to turn on off or adjust the fan speed. See Figure 18. A single
“beep” will conrm reception of the command.
OFF
Figure 17
OFF
Figure 18

38101-1-0318 Page 7
Remote Dimmer Control (Light)
To activate the light, use the Mode Button (Figure 3)
to index to the light icon. See Figures 19 and 20.
The intensity of the output can be adjusted through six levels.
Use the Up/Down Arrow Buttons (Figure 3) to adjust the output
level. A single “beep” will conrm reception of the command.
NOTICE: This function is available only with the IFC control Module.
OFF
Figure 19
OFF
Figure 20
Split Flow Control
The secondary burner is controlled by the split Flow. To activate
this function use the Mode Button (Figure 3) to index to the SPLIT
FLOW mode icon. See Figures 21 and 22.
Pressing the Up Arrow Button will activate the secondary burner.
Pressing the Down Arrow Button will turn off the secondary
burner. A single “beep” will conrm the reception of the command.
OFF
Figure 21
MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS
OFF
Figure 22
Continuous Pilot/Intermittent Pilot (CPI/IPI) Selection
With the system in “OFF” position press the Mode Button
(Figure 3) to index to the CPI mode icon. See Figures 25
and 26. Pressing the Up Arrow Button will activate the CPI.
Pressing the Down Arrow Button will return to IPI. A single “beep”
will conrm the reception of the command.
OFF
Figure 25
OFF
Figure 26

38101-1-0318Page 8
MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS
Button Lock
T his function will lock the Buttons to avoid unsupervised operation.
To ac tivate this function, press the MODE and UP Buttons at the
same time. See Figure 27.
To deactivate this function, press the MODE and UP Buttons at
the same time.
OFF
Figure 27
Low Battery Power Detection - Transmitter
The life span of the remote control batteries depends on various
factors: quality of the batteries used, the number of ignitions of
the appliance, the number of changes to the room thermostat set
point, etc.
When the transmitter batteries are low, an Icon will appear on
the LCD display of the transmitter See Figure 28 before all
battery power is lost. When the batteries are replaced this Icon
will disappear.
OFF
Figure 28

38101-1-0318 Page 9
When the IFC board goes into lockout:
1. both the Pilot and the Main Burner solenoids in the gas valve
are de-energized;
2. a diagnostic code is sent through the diagnostic red LED.
3. the IFC board will ignore any burner ignition command and
remain in the OFF state unless the unlock command se-
quence is met.
The causes of lockout must be investigated under safe
conditions by the user and/or the service personnel.
To reset the IFC from a lockout state, perform the following
procedure:
• Turn off the system power supplies (to the wall control or
remote control) for two or three seconds and then restore
power.
• Attempt to operate the insert. If the system returns to a
lockout state, contact your dealer for a service call.
Battery Backup Operation
Install batteries (See initialization sequence on page 4 or 11).
In case of power loss, the replace will switch to battery mode
automatically. The replace will operate normally without the fan
or light control when in battery mode.
Low Battery Detection
When the backup batteries are low, a double-beep will be emitted
when the module receives an on/off command. No commands
will be accepted until the batteries are replaced or the A/C power
is restored.
Lockout State Denition
A lockout state is reached when an ignition error occurs. This
could mean both an irregular ame detection and/or too many
unsuccessful ignition attempts. This state is a safe condition for
the appliance and is entered automatically by the IFC board.
The lockout state will remain set in memory as long as the power
supplies are applied.
MULTIFUNCTION REMOTE OPERATING INSTRUCTIONS
SEASONAL SHUTDOWN
1. At the end of the heating season turn off the replace insert
to prevent accidentall starting. Remove the barrier screen
and locate the switch at the lower right corner. Push the
switch to the OFF position. See Figure 29. Replace the
barrier screen.
SEASONAL ON/OFF
SWITCH LOCATION
Figure 29
2. Turn off gas to replace using the external shutoff valve (not
provided with insert). See page 10.
3. Remove the batteries from the transmitter and battery
backup. Purchase fresh batteries before the start of the next
heating season. See page 11.

38101-1-0318Page 10
FOR YOUR SAFETY READ BEFORE LIGHTING
1. Turn off all electric power to the appliance if service is to be
performed (if applicable).
2. Turn gas shut off valve to “OFF” position.
TO TURN OFF GAS TO FIREPLACE
A. This appliance is equipped with an ignition device which
automatically lights the pilot. Do not try to light the pilot
by hand, use the remote control. Before lighting the pilot,
ensure that the master switch is on. When lighting the pilot,
follow these instructions exactly.
B. Before lighting smell all around the appliance area for gas.
Be sure to smell next to the oor because some gas is
heavier than air and will settle on the oor.
What To Do If You Smell Gas
• Do not try to light any appliance.
• Do not touch any electrical switch;
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the re
department.
C. Use only the remote control or manual remote receiver
switch to operate the gas valve. Never use tools. If valve
does not operate, don’t try to repair it, call a qualied service
technician. Force or attempted repair may result in a re or
explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualied service technician to inspect the
appliance and to replace any part of the control system and
any gas control which has been under water.
INTERMITTENT PILOT LIGHTING INSTRUCTIONS
WARNING
If you do not follow these instructions exactly, a re or explosion may result causing property damage,
personal injury or loss of life.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above.
2. Turn OFF electric power to the appliance.
3. Remove front surround panel assembly or bottom louver if
included.
4. Turn gas shut-off valve counterclockwise to “On”
position.
5. Wait ten minutes to clear out any gas. Then smell for gas,
including near the oor. If you smell gas, STOP! Follow “B”
in the safety information above on this page. If you do not
smell gas, go to the next step.
6. Turn ON electric power to the appliance.
7. Turn main ame to on. If the pilot does not light within 60
seconds, stop and go to Step 5.
8. If the burner or pilot does not operate properly after several
tries, turn the gas shut-off valve clockwise to
“OFF” and call your service technician or gas supplier.
9. Replace the front surround assembly or close bottom louver
assembly (if applicable).
10. Operation of the gas valve is controlled by a manual on/
off switch or a hand held remote control. Refer to remote
instructions for detailed operation information.
SHUT-OFF VALVE