Enabling Devices 1521 User manual

For Technical Support:
Call our Technical Service Department
Monday through Friday, 9 a.m. to 5 p.m. (EST)
1-800-TEC-TOYS or 1-800-832-8697
[email protected]
Wireless TV Remote #1521
USER’S GUIDE
50 Broadway
Hawthorne, NY 10532
Tel. [phone] / Fax [phone]
Toll Free 800.832.8697
www.enablingdevices.com

Our oversized TV remote control is perfect for viewers with impaired motor
coordination. The wireless remote features a large striking area with 2" push
buttons. The buttons are clearly labeled with words and symbols for Channel,
Sound and On/Off functions. Uses infrared technology. It also will control the
latest flat screen TV’s. Five input jacks allow you to control the remotes with
any of our external Capability switches. (Not Included). Size: 15¾"L x 10½"W
x 3½"H. cannot be used with TV/VCR or TV/DVD combination units or
satellite TV. Requires 2 AA Batteries.
Operation:
1. Please refer to the manufacturer’s instruction manual included for
programming directions for this remote, with the exception of Step #1:
Installing the Batteries. Please see below:
2. The Remote requires 2 AA batteries (Not included). Use alkaline
batteries only (e.g. Duracell or Energizer brand). Do not use
rechargeable batteries or any other type of batteries because they supply
lower voltage and the unit will not perform properly. Never mix old and
new batteries together or different brands or types together.
3. You will not be placing any batteries directly into the “Sony” remote as
this is permanently affixed to the base. Instead, please locate the battery
compartment recessed in the back of the Remote base. The battery
compartment cover is secured with a small screw. Use a Phillips head
screwdriver to remove this screw and remove the cover. Insert the 2 AA
batteries into the compartment paying careful attention to proper battery
polarity.
4. Replace the compartment cover and re-secure it with the screw. Test the
unit by pressing the ON/OFF button. The red indicator light should blink.
If not, change your batteries.
5. All programming will be done through the remote’s keypad on the back of
this unit. When programming make sure none of the large buttons on the
front become activated or depressed, doing so will prevent programming
of your TV.
Switch Use:
7. You can plug up to 5 separate switches to control the same functions as
the large buttons; this is done via the input jacks located on the front side
of the unit.
Troubleshooting:
If you cannot get your Remote to operate you’re TV, or it will not perform
commands properly:
•Make sure that your batteries are fresh and installed correctly
(according to proper polarity). *
•If you are using external switches with your remote, make sure they
are plugged in all the way, there should be no gaps. Test your
switches on other switch adapted devices, to rule out your switches
as the source of the problem.
•Read the ”Sony’s” troubleshooting section of the guide for any
additional troubleshooting tips.
•Try ALL of the codes listed for your device. Many set-up codes may
allow partial functionality; however, only one code will operate your
device correctly.
•Make sure that you are within 6-10 feet of your device, with the
remote facing the device, while programming. Make sure that you
are within 15 feet of your device when using your remote.
•If the red light on the remote control does not blink when you press a
key, replace the batteries with two (2) new AA alkaline batteries. Be
sure to install paying close attention to proper battery polarity. *.
•* NOTE: When you replace your batteries, or remove them for any
reason, you must re-install batteries within 10 minuets, or re-
programming your remote will be required. This is why it is important
to write down the codes that work for your devices and keep both
these manuals in a safe place.
Care of Unit:
The Remote can be wiped clean with any household multi-purpose cleaner
and disinfectant. We recommend Simple Green, which is a non toxic
biodegradable all-purpose cleaner.
Do not submerge the unit, as it will damage the contents and the electrical
components.
Do not use abrasive cleaners, as they will scratch the surface of the unit.
Rev 12/7/10