EnaSolar GT Series User manual

Manufactured by: EnaSolar Limited
66 Treffers Road, Christchurch 8042, New Zealand
Tel [phone] | Fax [phone]
www.enasolar.net
one cool inverter.
GT Series Solar Inverter Quick Install Guide v1.4
See the next page before you begin.
This quick installation
guide must be used in
conjunction with the
Installation Manual.
For installation support
contact your local
approved distributor.
All safety warnings must
be strictly adhered to.
If the inverter is installed
incorrectly, this will void
the warranty.
1.5kWGT / 2kWGT / 3kWGT / 3.8kWGT

Before You Begin.
Before starting, you will need:
• Notebook/PCrunningMicrosoftXPorlater.
• InstallationUtility(contactyourdistributorforlogindetails).
• CommunicationsCable,USB–USBMini-B.
• CustomersSSIDandpasskeyfortheirwirelessrouter.
As well as this Quick Install Guide a Installation Manual, Wall Mounting Template
and Certificate of Conformity you will receive the following in the box...
1.UnpackingtheInverter.
FIRSTSTEP
1. Wall Mounting Case ...................x1
2.DisplayModule...........................x1
3. Inverter Module .......................... x1
4. Antenna ......................................x1
5. Conduit Bungs............................x2
6. Mounting Hardware.................... x6
5.
3. 4. 6.
1.
2.

2. Wall Mounting Module.NEXTSTEP
1.UnpackingtheInverter.
Undothe4xscrews,slidehandsunder
the Inverter Module and lift to assist in
removaloftheDisplayModule.
Then carefully disconnect the 3x
cablesfromthedisplayPCB(ground
tab, communications cable, Wi-fi
coaxialconnector).
SettheDisplayModuleaside.
Disconnectthe2xmaininverterconnectorsbysqueezingthesidereleasetabs
and carefully pulling out.
Lift off the Inverter Module and then set aside.

2. Wall Mounting Module.
Attach the provided Wall Mounting Template to the wall.
Drillthroughthetemplateinthespeciedlocations,thenremovethetemplate
from the wall.
Fit the Wall Mounting Box to the
wall using the supplied hardware.
(minimumof4xscrewsmustbeused.)
Note: Eliminate the contact of
dissimilar metals especially aluminium
(wall mounting box) and any steel
mounting hardware.
Seal any possible point of water
ingress by using a silicone sealant.
3.WiringtheAC&DCConnections.NEXTSTEP

3.WiringtheAC&DCConnections.
Thereare4xDCinputterminals(2x–VE&2x+VE,asshownbelow).Bothsets
ofinputsareconnectedinparallel,thereforewhenconnecting2xstringsofPV
panels, each string must be connected to an equal number of panels.
ItisbestpracticetoconnectthePV
panel frame to earth, run this cable
alongwiththeDCinputandconnect
to the earth bar.
SelectthePVpanelearthreference,
the default setting is disabled
(asshown).
Wirethephase(fedfromthecircuit
breakerintheswitchboard),neutral
conductors to their respective
terminals.
The earth conductor is to be
connected to the earth bar.
4. Connecting the Inverter.NEXTSTEP
PVEarthIsolated(Default).
Negative Earth Fault Fuse.PositiveEarthFaultFuse.

4. Connecting the Inverter.
Fit the Antenna by screwing in a clockwise direction.
Refit the Inverter Module to the Wall Mounting Module.
5. Configuration.NEXTSTEP
AtthispointtheDisplayModulecanhangontheearthcabletoallow
configuration.
Reconnectthe2xmainconnectors(DC&AC).
Thenreconnectthe3xconnectorstotheDisplayModulePCB(thegroundtab,
thecommunicationcableandtheWi-coaxialconnector).

5. Configuration.
ForcongurationtheDCinputmustbeturnedontopowertheinverter.
ConnecttheUSBcableandstarttheInstallationUtility.
6.FittingtheDisplayModuleandCommissioning.
NEXTSTEP Final step over page...
Enteralltheeldsinthesetuptab(generalandwireless).
Note: Ensure that you select the appropriate PV panel earth reference, the default
selection is disabled i.e. the earth fault fuse will not be monitored.
Further detail regarding the configuration process is available in the Installation
Manual.
Test the webpage by typing Enasolar-GT in the title bar of a web browser on a
computer on the local network.

For more detail see the full Installation Manual included.
After being certified by the lines distribution company, connect the AC to the unit.
TheDisplaymodulewilldisplay“InverterStartingUp”,then“Connectingtothe
GridinXsecs”whereXisthegridconnecttime.Thiswillcountdown,thenthe
inverterwillstartgeneratinganddisplaythegreenLED.
6.FittingtheDisplayModuleandCommissioning.
DisconnecttheUSBcableandttheDisplayModulebyscrewingthe4xcaptive
screws. Ensure that there are no cables that might get caught between the
inverter module and the display module.