Endeavor IO-510 User manual

INSTALLATION GUIDE
 
IO-505 7-1/4"x10"x7-1/2" (mountingbracketincreasesdepthby3/4")
IO-510 7-1/4"x10"x7-1/2" (mountingbracketincreasesdepthby3/4")
IO-570 7-1/4"x10"x7-1/2" (mountingbracketincreasesdepthby3/4")
IO-605 8-3/4"x11-3/8"x8-5/8" (mountingbracketincreasesdepthby1")
IO-805 10-5/8"x13-3/4"x10-5/8" (mountingbracketincreasesdepthby1-1/4")
Indoor / Outdoor Cabinet Loudspeakers
page 1 of 2Rev. A
Congratulations! You have purchased a high quality
stereo loudspeaker. When matched to comparable
electronic equipment, expect years of quality high
delity sound. We are constantly striving to provide
the very best technology has to offer.
The following manual is designed to give you,
the installer or owner, basic information as to
the speaker’s installation and operation. It is
beyond the scope of this manual to go into all the
details that must be taken into consideration in a
sophisticated high delity system.
If you have any questions regarding this speaker
which are not answered by this manual, contact your
local dealer for assistance. For the most current
information please visit www.oemsystems.com.
REAR CONFIGURATIONS
GENERAL DESCRIPTION
These two-way speakers have specially designed
woofers with linear long throw butyl rubber
surrounds for long life and superior damping. Dome
tweeters are utilized for excellent high frequency
dispersion throughout your entire listening
environment. The frame and grille can be custom
painted to match the room decor.
SHIPPING DAMAGE
Each speaker is thoroughly tested before it leaves
the factory. However, in shipment, accidents may
occur. Please inspect your speakers carefully
when you receive them to make sure there is no
damage. If there is, please notify your dealer, or
supplier immediately for assistance. If you received
your speakers by public transportation, report the
damage at once to the shipping company.
Overall (W x H x D)
page 1 of 2Rev. A
(2) Cabinet Speakers
(2) "U" brackets
notched &
solid end-caps
(not included w/ IO-510)
(8) rubber feet
Elegant cover
conceals and protects
connection terminals
Rear Mounted View with
SE-DBLSVL Swivel
Bracket (not included)
Bookshelf
Conguration
Shown with
the included
U-Bracket
BOx CONTENTS
Indoor / Outdoor
5-1/4", 6-1/2", 8" Cabinet Loudspeaker

page 2 of 2Rev. A
USING SPEAkERS wITHOUT BRACkETS
(BOOkSHELF CONFIGURATION / not available w/ IO-510)
This cabinet speaker may be set on a bookshelf, desktop,
stand, or other at surface. The speakers are shipped
with additional solid endcaps that provide a ner look
when the U-Brackets are not used.
1. Remove the endcaps by pulling the back
end of them away from the enclosure.
2. Loosen and remove the brass thumb screws
that hold the bracket to the speaker.
3. Remove the bracket and replace the thumbscrews.
Tighten them securely with your ngers.
4. Slip the front edge of the solid endcaps into the
available grooves and press the endcaps into place
ensuring that they engage with the thumbscrews.
5. Install the supplied vinyl feet to the bottom of
the speaker by peeling them from the sheet
and pressing them into place. They may also be
attached to the side of the speaker if one intends to
lay the speaker on its side.
INSTALLATION
(USING OPTIONAL DOUBLE SwIvEL BRACkET)
Follow the manufacturers
instructions for the installation of
the bracket. To prepare the speaker
for this type of bracket, remove the
supplied bracket and replace the
endcaps following steps 1-4 in the
previous section, “Using Speakers
without Brackets.” The bracket is
attached to the back of the speaker
using ¼-20 screws or bolts. The
length of the hardware will be
determined by the bracket thickness but it will likely
be about 1/2” to 5/8” in length. It will be necessary to
remove the terminal cover from back of the speaker. To
do this, use your nger(s) to pull back on the bottom of
the cover at the relief in the enclosure.
INSTALLATION
1. Determine the installation location of the speaker.
Use care to ensure the structure has the ability to
carry the weight of the speaker. We recommend
that the speaker be located where there is a stud or
other support structure especially if the speaker will
be oriented horizontally. If attaching to sheetrock
(gypsum board), ensure that you use suitable
hardware such as toggle anchors (not supplied).
2. Measure the hole-spacing on the bracket and
transfer these dimensions to the mounting surface.
3. Install the attachment hardware, drilling holes as
necessary.
In most installations the bracket will need to
be removed from the speaker so that it can
be tightened to the mounting surface without
obstruction.
4. Remove the endcaps by pulling the back end of them
away from the enclosure.
5. Remove the bracket from the speaker by loosening
and removing the brass thumb screws that hold the
bracket to the speaker.
6. Screw the bracket to the mounting surface. Either
set of holes may be used (slots or keyholes). If
the wire is coming through the wall then it can be
passed through the center-hole in the bracket if
desired or practical.
7. Prepare the wire for termination by stripping back
the insulation approximately
½” (13mm).
8. Remove the terminal cover from back of the speaker
using your nger(s) to pull back on the bottom of the
cover at the relief in the enclosure.
9. Attach the speaker to the bracket making the thumb
screws nger tight.
10. Position the speaker so the input terminals can be
accessed.
11. Pass the wire through the cover and connect it to
the input terminals, observing polarity to ensure
consistency.
12. Snap the terminal cover into place and rotate the
speaker in the desired direction.
13. Tighten the thumb
screws. A screwdriver
may be used to ensure
they are tight.
14. Re-install the endcaps.
page 2 of 2Rev. A
notched end cap - top
solid end cap - bottom
Indoor / Outdoor
5-1/4", 6-1/2", 8" Cabinet Loudspeaker