Bang & Olufsen BeoLab 4 PC User manual

BeoLab 4 PC
Guide

WARNING: To reduce the risk of fire or
electric shock, do not expose this appliance
to rain or moisture. Do not expose this equip-
ment to dripping or splashing and ensure
that no objects filled with liquids, such as
vases, are placed on the equipment.
To completely disconnect this equipment
from the AC Mains, disconnect the power
supply cord plug from the AC receptacle.
The lightning flash with arrowhead symbol
within an equilateral triangle, is intended
to alert the user to the presence of un-
insulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and main-
tenance (servicing) instructions in the
literature accompanying the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of
electric shock, do not remove
cover (or back).
No User-serviceable parts inside.
Refer servicing to qualified service
personnel.

Daily use
When you have finished setting
up the loudspeakers as described
on the following pages, connect
the entire system to the mains.
Cleaning the loudspeaker
You can clean the speaker panels
with a vacuum cleaner set to the
lowest suction level. Clean the other
surfaces using a soft, lint-free cloth
which you have dipped in lukewarm
water and wrung firmly.
Never use alcohol or other solvents
to clean any parts of the loud-
speaker!
Switching on and off
If you have set the LINE IN MODE
switch to AUTO, the loudspeakers
automatically switch on when they
receive an input signal – indicated
by green indicator lights. When you
switch off your system, the loud-
speakers will, after a few minutes,
automatically switch to standby –
indicated by red indicator lights.
However, if you have set the LINE IN
MODE switch to ON, the loud-
speakers are always switched on,
even when you switch off your
system.
In either setting of the LINE IN
MODE switch, the loudspeakers can
only be switched off completely by
disconnecting them from the mains
supply.
3
NOTE! Prolonged listening at high
volume levels may cause hearing
damage.
Indicator light

Set up the loudspeakers
We recommend that you follow
this procedure:
– Disconnect your system from the
mains.
– Connect the loudspeakers and set
the LINE IN MODE switch on
each loudspeaker as explained in
‘Cable connections’ (pp. 6–7).
– Connect the entire system to the
mains again.
The loudspeaker must be placed
standing upright on its base, or
fastened to one of the optional
accessories. Make the connections,
and set the switch before you
fasten the loudspeaker to one of the
accessories.
Cautions
– Make sure that the loudspeakers
are placed and connected in
accordance with the instructions
in this Guide. To prevent injury,
use Bang & Olufsen approved
stands and wall brackets only!
– Do not attempt to open the loud-
speakers. Leave such operations
to qualified service personnel!
The speaker panels, however,
may be removed for cleaning.
– The loudspeaker is designed for
indoor use in dry, domestic
environments only, and for use
within a temperature range of
10–40º C (50–105º F).
– For optimum sound quality, do not
place the loudspeaker enclosed in,
for example, a small bookcase.
Leave a minimum of 20 cm (8")
free space at the sides, and never
place anything directly in front of
the loudspeaker.
– Do not block the sound emitting
from the bass reflex port at the
bottom of the loudspeaker.
– Place the loudspeaker with its
front (the Bang & Olufsen name
plate) facing your favourite
listening position.
4

Loudspeaker front and side
panels
Each loudspeaker is equipped with
one front panel and two side panels.
These panels are fastened to the
loudspeaker with three small pegs
on the rear. The front panel is
marked with a Bang & Olufsen
name plate.
To remove the panels, for example
for cleaning, just pry the three pegs
in each panel free of the
corresponding holes (A–B) in the
loudspeaker. Fasten the panels again
by inserting the three pegs into the
corresponding holes in the front
and the sides of the loudspeaker.
Note: The product identification and
CE labels are placed on the loud-
speaker body behind the side panels.
A
A
A
B
B B
5

Cable connections
The loudspeakers are intended
for use with a personal computer.
They may also be used with non-
Bang & Olufsen audio or video
systems.
About the LINE IN MODE
switch …
The switch has two settings: ON
and AUTO. We recommend that
you set the switch to the same
position on each loudspeaker.
When set to ON, the loudspeakers
will not automatically switch to
standby when the sound signal
disappears. In this case, we
recommend that you switch off at
the mains supply, when not using
the system. When set to AUTO, the
loudspeakers automatically switch
on when you switch on the system.
When you switch off the system,
the loudspeakers will, after a few
minutes, switch to standby.
Connection to personal
computers
Use the enclosed connector to
connect the computer sound card
output to each of the loudspeakers.
As the sound signal from a computer
may vary (not constantly on), we
recommend that you set the
LINE IN MODE switch to ON. This
will prevent the loudspeakers from
switching off and on every few
minutes.
Connection to audio or video
systems
Connect the system to the LINE IN
socket on each loudspeaker (mini-
jack – mono).
Set the LINE IN MODE switch to
AUTO.
LINE IN
AUTO ON
LINE IN MODE
~
6
The sockets and the switch are
located in the base of each loud-
speaker.

LINE IN connections: Output
from computer sound cards often
carry both the left and right sound
channels in one socket. Therefore,
use the enclosed connector when
connecting the loudspeakers to a
personal computer (fig 1). Connect
the plug marked L to the left loud-
speaker, and the plug marked R to
the right loudspeaker.
If you connect the loudspeakers to,
for example, a non-Bang & Olusen
audio or video system with separate
connections for the left and right
sound channels, make the
connections as shown in fig. 2.
Mains connections: Depending
on the type of mains supply
connector enclosed with your loud-
speakers, connect each loudspeaker
to the mains as shown in either
fig. 3 or fig. 4.
Cable Clamp: For safety reasons,
the mains lead to each loudspeaker
must be secured with the cable
clamp provided.
L R
L R
7
1 2
3 4

The European Parliament and the
Council of the European Union
have issued the Waste Electrical
and Electronic Equipment Directive.
The purpose of the Directive is the
prevention of waste of electrical
and electronic equipment, and to
promote the reuse and recycling
and other forms of recovery of
such waste. As such the Directive
concerns producers, distributors
and consumers.
The WEEE directive requires that
both manufacturers and end-
consumers dispose of electrical
and electronic equipment and
parts in an environmentally safe
manner, and that equipment and
waste are reused or recovered for
their materials or energy.
Electrical and electronic equipment
and parts must not be disposed of
with ordinary household refuse; all
electrical and electronic equipment
and parts must be collected and
disposed of separately.
Products and equipment which
must be collected for reuse,
recycling and other forms of
recovery are marked with the
pictogram shown.
When disposing of electrical and
electronic equipment by use of the
collection systems available in your
country, you protect the
environment, human health and
contribute to the prudent and
rational use of natural resources.
Collecting electrical and electronic
equipment and waste prevents the
potential contamination of nature
with the hazardous substances
which may be present in electrical
and electronic products and
equipment.
Your Bang & Olufsen retailer will
assist with and advise you of the
correct way of disposal in your
country.
Waste Electrical and Electronic Equipment (WEEE) –
Environmental protection
8

For the US-market only!
NOTE: This equipment has been
tested and found to comply with
the limits for a class B digital device,
pursuant to part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection
against harmful interference in a
residential installation.
This equipment generates, uses
and can radiate radio frequency
energy and, if not installed and
used in accordance with the
instructions, may cause harmful
interference to radio
communications. However, there is
no guarantee that interference will
not occur in a particular
installation. If this equipment does
cause harmful interference to radio
or television reception, which can
be determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between
the equipment and receiver.
– Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
– Consult the retailer or an
experienced radio/TV technician
for help.
For the Canadian market only!
This class B digital apparatus meets
all requirements of the Canadian
Interference-Causing Equipment
Regulations.
This product fulfils the
conditions stated in the
EEU directives 89/336 and 73/23.
Technical specifications, features
and the use thereof are subject to
change without notice!
Til det norske marked!
Mekaniske og elektroniske kompo-
nenter i produktene slites ved bruk.
Det må derfor påregnes reparasjo-
ner og utskiftning av komponenter
innenfor kjøpslovens reklamasjons-
tid, som må regnes som vedlikehold
av produktene. Slik vedlikehold gir
ikke grunnlag for å rette mangels-
krav mot forhandler eller leverandør,
og må bekostes av kjøper.
9