ENDIAN 4i Edge XL User manual

Secure everyThing
www.endian.com
Endian 4i Edge XL Quick Starter
www.endian.com
Status /Activity LED
Digital I/O Ports
Reset Switch
WiFi & CELL
Ethernet Ports
4i Edge XL Quick Starter
LED Table
Color -GREEN BLUE RED
StatussOFF Solid Slow
Blinking Flashing Solid Slow Blinking
Fast
blinking Solid Flashing
Power No Power Power On - - - - - -
Status - System up
Support
Access
Enabled
Provisioning System boot
(Bootloader)
System boot
(Kernel)
System boot
(Operating
System)
- Fatal Error
Uplink -Main uplink
online - - Secondary
uplink online -All uplinks
offline -
VPN/SB
Not
Congured
or Enabled
OpenVPN
Client or
Connecting
At least 1
Enabled
OpenVPN
Client
Connection
Established
- - - -
All Enabled
OpenVPN
Client Con-
nections in
Error Status
-
Connector Pinout Table
COM Ports
1 2 3 4 5
6 7 8 9
Pin RS232 RS485 RS422
1DCD DATA - TX-
2RXD DATA + TX+
3TXD RX+
4DTR RX-
5GND GND GND
6DSR
7RTS
8CTS
9RI
Digital I/O
GND1234DI
VCC1234DO
Pin REF
GND GND
DI 1 INPUT 0
DI 2 INPUT 1
DI 3 INPUT 2
DI 4 INPUT 3
VCC VCC (IN)
DO 1 OUTPUT 0
DO 2 OUTPUT 1
DO 3 OUTPUT 2
DO 4 OUTPUT 3
USB Ports
SIM Card / Micro SD Slot
Console
Power Input
COM Ports

Endian 4i Edge XL Quick Starter
www.endian.com
SIMCARD
What You Get and What You Need
Included in the box you will find:
• Endian Edge XL incl. DIN Rail mounting
• DI/DO phoenix connector
• DC power phoenix connector
To install your Endian 4i Edge XL and protect your network you need:
• Power connection
• Ethernet switch (connected to your network)
Optionals:
4G Kit:
• 4G module (mounted), 2x antennas
WiFi Kit:
• WiFi module (mounted), 2x antennas
Installation
A DHCP server is running on Ethernet port 1 of your appliance. If you already have a DHCP server in your local
network make sure to connect your computer directly to Ethernet port 1, go through the installation procedure
and connect the appliance to your local network only after having disabled the DHCP server.
1. Place the appliance on a steady surface or attach it to the DIN rail.
2. Connect your computer to Ethernet port 1.
3. Connect the port 5 of your device Appliance to the uplink. The appliance will automatically try to connect to
the Internet via DHCP once turned on. If you are using a mobile broadband connection and you have the 4G
modem, insert your SIM card now.
4. Connect the DC power socket to the unit. The Appliance turns ON.
If your device was precongured using the Plug & Connect feature, there are no additional steps to complete
(you can skip the Web Interface section below). You can check that the Plug & Connect procedure completed
successfully by accessing your Endian Switchboard and verifying your device is listed as online and available.
Web Interface
1. After booting the appliance your PC will automatically get an IP address from the Endian appliance.
If your computer is not set up to configure its IP address through DHCP you will need to configure
your PC’s Ethernet interface manually. In that case configure your interface with an IP address be-
longing to the 192.168.0.0/24 subnet that is different from 192.168.0.15 (which is the IP address
of the Endian appliance).
2. Open your Internet browser (e.g. Mozilla Firefox) and go to address 192.168.0.15
• The system will redirect you to https://192.168.0.15:10443/ and the Configuration Wizard will start.
Activation & Configuration
You have 3 choices:
• Plug & Connect: if you have an Endian Switchboard this
is the easiest way to connect and activate your Endian
4i Edge XL.
In order to utilize the Plug & Connect feature the
device must be congured on the Switchboard
(for more info please consult the “The Plug And
Connect (Autoregistration) Procedure” article on
help.endian.com)
• Restore a Backup: choose this mode if you have any
existing backup to restore.
• Setup Assistant: if you want to congure your appliance manually with the conguration wizard, choose this
mode and follow the steps.
Registration
The Configuration Assistant will ask you for an Endian Network account, needed for your Endian Network sub-
scription and keep your appliance always up-to-date with the latest features and security updates.
A. You already have an Endian Network account
1. When the system asks you if you have an Endian Network account choose “yes” and go to the next step.
2. Now fill in the form using your data and the activation code.
B. You do not have an Endian Network account
1. When the system asks you if you have an Endian Network account choose “no” and go to the next step.
2. Click on the “Endian Network account” link and insert the activation code on the back of this Quick Start.
3. Fill in the registration form and create your account.
4. Close the registration window and go to the next step.
5. Now fill in the form using your data and the activation code.
Your Endian appliance is now ready!
Insert MICRO SD Insert SIM
Expansion slots