Eneo PLD-2036PTZ User manual

Quick Installation Guide
1/4 " Network High Speed Dome, PTZ, 36x, Day&Night
PLD-2036PTZ

Safety Instructions _______________________________________________
• Read these safety instructions and the operation manual first before you install and commission
the camera.
• Keep the manual in a safe place for later reference.
• Protect your camera from contamination with water and humidity to prevent it from permanent
damage. Never switch the camera on when it gets wet. Have it checked at an authorized service
center in this case.
• Never operate the camera outside of the specifications as this may prevent the camera
functioning.
• Do not operate the cameras beyond their specified temperature, humidity or power ratings.
• Operate the camera only at a temperature range of -40°C to +50°C and at a humidity of max. 90%.
• To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.
• Pay attention when laying the connection cable and observe that the cable is not subject to heavy
loads, kinks, or damage and no moisture can get in.
• Do not attempt to disassemble the camera board from the dome.
• The warranty becomes void if repairs are undertaken by unauthorized persons.
Do not open the camera housing.
• Never point the camera towards the sun with the aperture open. This can destroy the sensor.
• Installation, maintenance and repair have to be carried out only by authorized service centers.
Before opening the cover disconnect the unit from mains input.
• Contact your local dealer in case of malfunction.
• Only use original parts and original accessories from Videor E. Hartig GmbH.
• Do not use strong or abrasive detergents when cleaning the dome.
Use a dry cloth to clean the dome surface.In case the dirt is hard to remove, use a mild detergent
and wipe gently.
• All openings provided in the housing for assembly purposes must be closed and/or sealed.
• The installer is responsible for ensuring that the degree of protection as per the technical
specifications is upheld, e.g. by using all enclosed gasket seals and O-rings, by
waterproofing the cable exits with silicon or through laying the cable in such a way that the
cable does not act as a „gutter”.
• During assembly, care must be taken to ensure that existing seals are correctly inserted
and are not displaced as a result of assembly.
You must not continue to use damaged seals.
NOTE:
This is a class A digital device. This digital device can cause harmful interference in a
residential area; in this case the user may be required to take appropriate corrective action at
his/her own expense.

This Quick Guide is for quick installing and connecting the network Speed Dome Camera.
For details, please refer to the camera’s User Manual and Installation Guide.
Switch Definition _____
Outdoor
A None
B Communication Switch (Reserved)
C RJ45 Connector
D 22-Pin Connector
E None
F F-1 Reboot Button
F-2 Factory Reset Button
G ISP Connector (for FW upgrade)
Data Cable and Connector Definition _____
Please refer to the illustrations below for connector definition of each kind of Data Cable before
wiring.
Outdoor Dome Camera:
AC 24V Data Cable

22-Pin Connector Definition _____
When cabling, please refer to the table below for pin definition of the Data Cable’s 22-pin connector
on the Data Cable.
Pin Definition Cable Pin Definition Cable
1AC 24-1/DC (＋) 20AWG/18AWG 12 ALM-1
2ALM NC 13 ALM-3
3AC 24-2/DC (－) 20AWG/18AWG 14 ALM-2
4ALM NO 15 ALM-4
5FG 20AWG18AWG 16 Reserved
6 ALM COM 17 Reserved
7 Audio in
24AWG
18 Reserved
8 Audio out 19 Reserved
9 Audio GND 20 ALM GND
10 Audio GND 21 VGND 20AWG
11 ISOG 22 Video
Before Login to the Camera _____
A client program will be automatically installed on your PC when connecting to the network Speed
Dome Camera. Before logging in to the Dome Camera, please ensure downloading the ActiveX
control is allowed by either changing the ActiveX controls and plug-ins or setting Internet’s security
level to default. For further details, please refer to the network Speed Dome Camera’s Software
Guide.
ActiveX Controls and Plug-ins Settings Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of
the browser. Then Click on <Internet
Options>.
Step 3: Click on the <Security> tab and select
“Internet”, and click on <Custom level>
to change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins”
items to <Prompt> or <Enable>.
Step 1:Start the IE.
Step 2:Select <Tools> from the main
menu of the browser. Then Click
on <Internet Options>.
Step 3: Click on the <Security> tab and
select “Internet.”
Step 4: Down the page, press “Default
Level” and click on <OK> to
confirm the setting. Close the
browser window, and open a new
one later for accessing the IP
Camera

Camera Login _____
The network Speed Dome Camera’s default IP address is: 192.168.1.10. Therefore, to access the
camera for the first time, set the PC’s IP address as: 192.168.1.XXX; for example:
IP Address: 192.168.1.20
Subnet Mask: 255.255.255.0
Login ID & Password
• Key in the camera’s IP address in the URL bar of the Web browser window and hit “Enter.”
• Enter the default user name (admin) and password (admin) in the prompt request dialogue.
Note that user name is case sensitive.
Install the ActiveX Control
• After connecting to the network Speed Dome Camera, the request for installing the ActiveX
control will appear just below the URL bar.
• Right Click on the information bar, and press “Install ActiveX Control…” to permit ActiveX control
installation.
• In the pop-up security warning window, click on <Install> to start downloading DC Viewer software
on the PC.
• Click on <Finish> after DC Viewer installation is complete.
Browser-based Viewer _____
The main page of the network Speed Dome Camera user interface is as shown below.

Technical Specifications _____
Type PLD-2036PTZ
Art. No. 200823
Resolution standard SD
System day&night
Sensor size 1/4”
Imager CCD
Sensitivity (at 50% video signal) 1Lux (colour) ; 0.01Lux (B&W)
Horizontal resolution 650 TVL
Automatic gain control (AGC) supplied
Automatic electronic shutter (ESC) 1/50 ~ 1/10,000sec.
Digital Noise Reduction (DNR) yes, 2D & 3D
Low speed shutter yes, ON/OFF switchable
White balance automatic, indoor, outdoor, ATW, manual
Backlight compensation BLC
Wide Dynamic Range (WDR) yes
IR cut filter switchable
Resolution max. 720x576
Resolution 720x576 (4:3)
Image transmission rate max. 25 images/sec.
Frame 25fps at 704x576
Privacy zones masking 16 zones masking, ON/OFF switchable
Activity detection yes
Motion detector 10 zones
Analysis functions activity detection
Text display supplied
Sharpness correction adjustment range: 0 ~ 15
Menu languages German, English, French, Italian, Russian
OSD function control resolution, modes (presets), motion detection, BLC,
DNR, WDR, bit rate, day&night, password
External connections alarm input, alarm output, audio input, audio output
Video outputs composite (CVBS), 1Vp-p (C)VBS, 75ohms, BNC
Audio support yes
Audio 1/1 Line input and output
Alarm inputs 4
Alarm output 1x Relay out (AC120VAC 30VDC)
Alarm processing SD-card recording, alarm out, FTP, E-Mail, PTZ action
Internal storage microSD card
Compression standard H.264, MJPEG
Audio standards G.711, G.726, ADPCM/AAC
Bandwidth controllable bandwidth and frame rate
Stream types H.264, MJPEG multiple
Network connection RJ-45
Network interface 10/100Base-TX, RJ45
Web browser MS Internet Explorer vers. 7.0 or higher, Safari (Java),
Mozilla Firefox (Java), Google Chrome (Java)
Network protocols TCP/IP, UDP, RTP, RTSP, HTTP, HTTPS, ICMP, FTP,
SMTP, DHCP, PPPoE, UPnP, IGMP, SNMP, IPv4, IPv6,
IEE 802.1
Lens type zoom
Lens mount -
Focal length 3.4mm – 122.4mm

Horizontal angle of view 50.4° - 1.4°
Aperture range F1.6~F4.5
Digital zoom 12x
Iris control DC
Focus control automatic and manual
MOD (Minimum object distance) 0.5m
Illumination no
Serial interfaces no
Remote configuration via web browser
Firmware update via network interface
Operation protection Password protected
Password protection yes, two levels (administrator and user)
e-PTZ support no
Speed (manual control) 1-80°/sec.
Preset speed up to 400°/sec.
Rotation range 360° (endless)
Auto flip function mechanical, digital, off
Proportional pan and tilt continually decreases pan and tilt speeds in proportion
to depth of zoom
Patterns 8 pattern
Presets 256 Presets
Home position included (with multiple park actions)
Tours up to 8 user programmable guard tours
Supply voltage 24VAC
Power over Ethernet no
Heater yes
Power consumption 65W
Mounting optional wall/flush mounting accessories
Temperature range (operation) -40°C~+50°C
Vandalism resistant yes
Housing outdoor
Housing material plastic
Colour (housing) RAL9003
Colour (bubble) clear
Protection rating IP66, IK10
Management Software Support Zelaris
SDK available
ONVIF core specifications 1.02
Certificates CE
Dimensions See drawing
Weight 2.6kg
Parts supplied remote viewer software, screw set, manual
Special features Auto calibration
Optional Accessories
The optional accessories currently available can be found on our Homepages: www.videor.com and
www. eneo-security.com

eneo
®
is a registered trademark of Videor E. Hartig GmbH
Exclusive distribution through specialised trade channels only.
Videor E. Hartig GmbH
Carl-Zeiss-Straße 8 · 63322 Rödermark, Germany
Tel. [phone] / 888-0 · Fax [phone] / 888-100 V 1.4
www.videor.com Technical changes reserved.
www.eneo-security.com © Copyright by Videor E. Hartig GmbH 05/2012