ENFORCER DP-266-1C3Q User manual

®
DP-266-1C3Q
Wireless Video Door Phone
Manual
Features:
Wireless operation –camera and monitor can
operate from up to 492ft (150m)** away
Remotely and securely talk to visitors and
unlock doors or gates via the monitor
Lightweight monitor can be carried around the
premises while talking to the visitor
Connect up to two additional monitors and one
additional camera*
Intercom calling between paired monitors*
Camera has built-in IR LEDs for nighttime
operation
Camera includes a built-in PIR sensor that
activates the camera and takes photos of the
visitor when they approach
Monitor includes a kickstand and a charging base
Camera powered by 9~16 VAC/5~16 VDC
Monitor front door at any time
Egress input
170° wide field of view
Adjustable camera pan and tilt angle—up to 20°
from centerline in any direction—to allow for
mounting variations
*Additional monitors and camera sold separately.
**Line-of-sight range. Actual range may vary depending on the installation and operating environment.
*

ENFORCER Wireless Video Door Phone
2SECO-LARM U.S.A., Inc.
Table of Contents:
Parts List:
Introduction:
DP-266-1C3Q
Complete Kit
1x
Monitor (DP-266-M3Q)*
1x
Camera (DP-266-CQ)*
1x
Monitor charging stand
1x
Monitor kick stand
1x
AC Power adapter with USB port
(for monitor)
1x
USB Cable
1x
Monitor battery
1x
Camera mounting hood bracket
1x
AC Power adapter with DC plug
(for camera)
1x
DC Jack with pigtail
1x
Camera battery
3x
Camera mounting screws
3x
Camera mounting screw anchors
1x
Camera screw
1x
Camera screw cover
1x
Manual
DP-266-M3Q
Additional Monitor Unit
1x
Monitor (DP-266-M3Q)**
1x
Monitor charging stand
1x
Monitor kick stand
1x
AC Power adapter with USB port (for monitor)
1x
USB Cable
1x
Monitor battery
1x
Manual
DP-266-CQ
Additional Camera Unit
1x
Camera (DP-266-CQ)**
1x
Camera mounting hood bracket
1x
AC Power adapter with DC plug (for camera)
1x
DC Jack with pigtail
1x
Camera battery
3x
Camera mounting screws
3x
Camera mounting screw anchors
1x
Camera screw
1x
Camera screw cover
1x
Manual
Introduction................................................................ 2
Parts List.................................................................... 2
Specifications ............................................................ 3
Overview.................................................................... 3
Display Overview....................................................... 4
Installation Notes....................................................... 4
Camera Wiring Diagram............................................ 5
Sample Application.................................................... 5
Installation –Camera................................................. 6
Installation –Monitor ............................................. 6~7
On-Screen Display Features ..................................... 8
Programming and Using the
On-Screen Display...........................................9~10
Programming the Advanced Settings ................10~11
Operating the Wireless
Video Door Phone .........................................12~13
Resetting the Camera and
Pairing a First Monitor....................................13~14
Pairing Additional Monitors or Cameras ..................14
Tamper Alarm ..........................................................15
Troubleshooting .......................................................15
Warranty...................................................................16
The ENFORCER Wireless Video Door Phone is a convenient and secure way to monitor and
control an entryway, such as a door or gate, from up to 492 feet (150 meters) away.
When a guest or visitor presses the doorbell button on the camera unit, the homeowner can use
one of up to three lightweight, wireless LCD monitors to see whom is requesting entry, speak with
the caller, take a photo, and decide whether or not to grant entry. The video door phone can be
expanded with up to two additional monitors and one additional camera. If multiple monitors are set
up, then the system can also be used as an intercom system between each monitor.
*The DP-266-1C3Q included monitor and camera are paired by default.
**Additional monitors and cameras are not paired by default. See "Pairing Additional Monitors or Cameras" on pg. 14.

ENFORCER Wireless Video Door Phone
SECO-LARM U.S.A., Inc. 3
Specifications:
Overview:
33/8" (86mm)
MENU
EXIT
OK
Reset
Camera:
Wiring connections
(see pg. 5)
Reset button
Battery cover
Camera
IR LEDs
PIR Sensor
Speaker
Status LED
Doorbell
Microphone
Monitor:
Charging
indicator
Status LED
OK/Talk
Menu/Unlock
Exit/View
Microphone
Up
Down/Photo
Volume up/down
ON/OFF Button:
-Turn monitor
ON/OFF
-Standby mode
USB Connector
(Mini-B)
Camera angle
adjustment joystick
USB Connector
(not used)
Camera
Type
Color camera
Chip
CMOS
Resolution
480 TV Lines
Lens
2mm
Field of view
170°
Camera angle adjustment
Up to 20° any direction
Operating voltage
9~16 VAC/5~16 VDC
Relock delay
3/6/8 Seconds
Relay output
3A@250VAC/30VDC
Current
draw
Active
300mA@12VDC
Standby
15mA@12VDC
Battery
life
Active
~7 Hours
Standby
~60 Days
IR LED Range
5' (1.5m)
IR LED Frequency
940nm
PIR Detection range
9' (3m)
PIR Detection angle
60°
Dimensions
(with bracket)
511/16"x31/8"x115/16"
(144x80x50 mm)
Weight
4.3-oz (122g)
Operating temperature
14°~122° F (-10°~50° C)
Monitor
Display
33/8" (86mm) TFT
Operating voltage
5VDC (adapter) or
3.7VDC (battery)
Current
draw
Active
[email protected]C
Standby
[email protected]
Battery
life
Active
~2.5 Hours
Standby
~7 Days
Operating frequency
2402~2480 MHz
RF power
120mW
Wireless range
492' (150m)*
Dimensions
5"x33/8"x7/8"
(127x85x22 mm)
Weight
3.9-oz (110g)
Operating temperature
32°~104° F (0°~40° C)
*Line-of-sight range. Actual range may vary depending on the
installation and operating environment.

ENFORCER Wireless Video Door Phone
4SECO-LARM U.S.A., Inc.
: ID –Displays the monitor ID number
: Signal Strength –Displays the wireless signal strength
: Communication Mode –Displays current communication mode
–Bell indicates an incoming call
–Crossed out microphone indicates one-way communication
–Microphone indicates two-way communication
: Message –Displays when there is a message due to a missed call
: PIR –Displays when the PIR sensor is turned on
: Photo –Displays when a photo is taken
: Relay –Displays while the relay is active
: Alarm –Displays when the tamper alarm has been activated
: Monitor volume –Displays the current monitor volume
: Monitor Battery: Displays the current monitor station battery level
: Camera Battery: Displays the current camera station battery level
Display Overview:
Installation Notes:
115º
Camera with No Tilt
Camera Tilted
115º
Up 20º
170º
Left 20º
170º
1. Unpack the video door phone and note the included parts.
2. Read this manual thoroughly. A clear understanding of the manual will make installation and
operation much easier.
3. Find a good location to mount the monitor and camera. Approximately 5ft (1.5m) above the
ground is optimal, where the visitor would stand approximately 2.5~5 ft (0.8~1.5 m) from the
camera. Note that the camera tilt and pan angle can be adjusted up to 20° from centerline to
compensate for less than optimal situations (see below).
4. Avoid mounting the camera or monitor near sources of strong electromagnetic signals or other
electronic devices that may cause interference.
5. Avoid mounting the camera in direct sunlight or exposing the camera to strong vibrations, direct
rain, or moisture, which could result in damage to the camera. Strong backlight or reflection
may degrade the resulting video image.
6. The monitor and camera contain no user-serviceable parts. Opening them may damage
sensitive components and will void the warranty.

ENFORCER Wireless Video Door Phone
SECO-LARM U.S.A., Inc. 5
Reset
Camera Wiring Diagram:
Sample Application:
COM
N.C.
N.O.
Egress input (N.O., -)
(+)
(–)
PUSH
TO
EXIT
Request-to-exit plate
Electric strike
power supply
Fail-secure
electric strike
To the included AC adapter or
the doorbell's transformer
Negative (-) (black wire)
Positive (+) (red wire)
1 2 3 4 5 6
Camera
6
5
4
3
2
1
The camera is connected to its included AC adapter.
The egress input is connected to a Request-to-Exit Plate. The homeowner can exit the
premises by pressing this button.
The N.O. (normally open) output is wired to an electric lock. The camera and the
Request-to-Exit Plate both activate the strike, allowing entry or egress.
The electric lock's power supply is wired to the COM (common) output.
1. Positive (+) power input –Connect to the red wire of the included AC adapter or to the positive
wire of the doorbell's power supply.
2. Negative (-) power input –Connect to the black wire of the included AC adapter or to the
negative wire of the doorbell's power supply.
3. Egress (N.O.) negative input –Connect to an optional N.O. egress device. The egress device
will activate the relay for the same length as the lock delay. (See the "Unlocking duration"
section in "Programming the Advanced Settings," pg. 11).
4. N.O. (Normally opened) output –Wire to the lock device for fail-secure operation.
5. N.C. (Normally closed) output –Wire to the lock device for fail-safe operation.
6. Common output –Wire to the power supply of the lock device.
NOTE: For 16VAC doorbell installation, wire directly from the doorbell's transformer.
COM
N.C.
N.O.
Egress input (N.O., –)
(–)
(+)
9~16 VAC/
5~16 VDC
Relay
Output

ENFORCER Wireless Video Door Phone
6SECO-LARM U.S.A., Inc.
Installation –Camera:
BP-6M
5ft
(1.5m)
Install the monitor battery:
Remove the battery cover
on the back of the monitor
and insert the included
BP-6M lithium-ion battery.
1. Position the camera so the area to be monitored is easily visible,
optimally 5ft (1.5m) above the ground. Do not position the camera in
direct sunlight, or where it will be exposed directly to rain or snow.
NOTE: For best results, the visitor should stand 2.5~5 ft (0.8~1.5 m)
away from the camera.
2. Cut a hole large enough to run the min. 21AWG 2-conductor wire to
the door unlock device through the wall, as well as to the included
power supply.
3. Mount the camera bracket to the wall with three screws. Use screw
anchors if the bracket is mounted on drywall or brick.
4. Run the 2-conductor wire from the camera, through the wire hole in
the bracket, to the optional door unlock device.
5. Install the rechargeable lithium ion battery into the camera. The
battery will act as a backup power source in case of a power outage.
6. Connect the AC adapter (see "Camera Wiring Diagram," pg. 5).
7. Install the monitor battery (see below) and turn on the camera and
monitor. If the camera is not in the bracket, the tamper alarm will
sound. Press the "OK" button on the monitor repeatedly to disable
the tamper alarm.
8. Experiment with the camera angle using the joystick on the back of
the camera to adjust the direction of the camera while viewing the
image on the monitor.
9. Mount the camera into the bracket:
Push the top of the camera into the top of the bracket.
Push the bottom of the camera into the bottom of the bracket.
Screw in the bottom of the camera to fix the camera into the
bracket and push the plastic screw cover into the bottom of
the bracket, over the screw.
NOTE: Do not block the PIR sensor on the camera.
Reset
21/8" (54mm)
33/4"
(96mm)
Camera
Angle
Adjustment
Joystick
Installation –Monitor:

ENFORCER Wireless Video Door Phone
SECO-LARM U.S.A., Inc. 7
Installation –Monitor (continued):
MENU
EXIT
OK
1. Place the
monitor into the
monitor charger
stand and plug
the charger into
the stand.
2. Plug the charger directly into the monitor.
ON/OFF
Battery
level
indicator
Standby/
Low
battery
indicator
Recharge the monitor battery:
There are two ways to recharge the monitor battery.
Turn monitor ON:
Hold the "ON/OFF" button for 3 seconds. The monitor will turn
ON with the ENFORCER screen.
Standby mode:
If the display is OFF, press the "ON/OFF" button momentarily
to leave standby mode and turn the display ON. The red
indicator LED will flash once every three seconds in
standby mode.
Low battery:
When the battery is low (indicated by 1 or 0 bars on the
display's battery icon), the red indicator LED will start to flash
once per second.
Turn monitor OFF:
While the monitor's display is ON, hold the "ON/OFF" button
for 3 seconds and the Shutdown menu will come up. Select
"YES" to turn the monitor OFF.
MENU
EXIT
OK

ENFORCER Wireless Video Door Phone
8SECO-LARM U.S.A., Inc.
On-Screen Display Features:
Photos –View and delete photos taken by the camera station. There are four different
types of photos
M –Photos taken by the user manually (1 photo taken).
A –Photos taken by the camera station automatically when the doorbell button
is pressed (1 photo taken).
T –Photos taken by the camera station automatically when the unit is removed
from the bracket and the tamper alarm activates (4 photos taken).
P –Photos taken by the camera station automatically when the PIR function is
activated (3 photos taken).
Messages –View photos from missed calls, same as "Automatic" photos.
Time –Set the time and date.
Ring –Choose from four different ring tones (Telephone, Doorbell, Für Elise, or Jingle
Bells) and set ring volume (six volume levels).
Language –Choose from English, German, Spanish, French, Russian, or Chinese
language formats.
Setup –Set advanced settings such as Motion detection, Backlight time, Unlocking
duration, Pairing, Alarm settings, or Version information.

ENFORCER Wireless Video Door Phone
SECO-LARM U.S.A., Inc. 9
Programming and Using the On-Screen Display:
1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display.
2. Use the "Up" and "Down" buttons to move the cursor up or down. Use the "Menu/Unlock" button
to move the cursor to the right.
3. To select a Menu option, highlight the option and press the "OK" button.
4. To exit the on-screen display, press the "Exit" button.
NOTE: If there is no activity, the monitor will exit programming mode and the display will turn off in
35 seconds.
Viewing and deleting photos:
1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display.
2. Highlight the "Photo" icon and press the "OK" button to enter the "Photo" screen.
3. Use the "Up" and "Down" buttons to select the photo to be viewed.
NOTE: Photos are saved with the following format: "X-HHMMSS-YYMMDD.jpg" with "X"
being the type of photo, "HHMMSS" being the time the photo was taken, and
"YYMMDD" being the date the photo was taken.
4. Press the "OK" button and select from "View," "Delete," or "Delete All."
a. Press "View" to view a photo.
b. Press "Delete" to delete the selected photo (after an additional prompt).
c. Press "Delete All" to delete all photos (after an additional prompt).
5. Once viewing a photo, press the "Up" or "Down" buttons to cycle through other photos.
6. Press the "OK" button to either delete or exit the photo viewing mode and go back to the
on-screen display menu.
NOTE: The monitor can save up to 240 photos. Photos are saved in a "first-in, first-out" method,
meaning that the system automatically deletes the oldest photo.
NOTE: There is no way to export any of the photos on the device.
Viewing and deleting messages:
1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display.
2. Highlight the "Messages" icon and press the "OK" button to enter the "Messages" screen.
3. Use the "Up" and "Down" buttons to select the message to be viewed.
NOTE: Messages are the same as Automatic photos but are saved with the following format:
"HH:MM:SS MM-DD-YYYY."
4. Press the "OK" button and select from "Open," "Delete," or "Delete All."
a. Press "Open" to view a message.
b. Press "Delete" to delete the selected message (after an additional prompt).
c. Press "Delete All" to delete all messages (after an additional prompt).
5. Once viewing a message, press the "OK" button to return to the "Messages" screen.
NOTE: The monitor can save up to 10 messages. Messages are saved in a "first-in, first-out"
method, meaning that the system automatically deletes the oldest message.
NOTE: Messages will not be saved if the indoor monitor is off.

ENFORCER Wireless Video Door Phone
10 SECO-LARM U.S.A., Inc.
Programming and Using the On-Screen Display (continued):
Programming the Advanced Settings:
Programming the time and date:
1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display.
2. Highlight the "Time" icon and press the "OK" button to enter the "Time" screen.
3. Use the "Up" and "Down" buttons to adjust the value. Use the "Menu/Unlock" button to move to
the next value.
4. Press the "OK" button when finished programming to go back to the on-screen display menu.
NOTE: The time is set in 24-hour time format.
Programming the ringer:
1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display.
2. Highlight the "Ring" icon and press the "OK" button to enter the "Ring" screen.
3. Use the "Up" and "Down" buttons to select one of four ring tones: Telephone (default), Doorbell,
Für Elise, or Jingle Bells.
4. Press the "OK" button when finished programming to go back to the on-screen display menu.
Programming the language:
1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display.
2. Highlight the "Language" icon and press the "OK" button to enter the "Language" screen.
3. Use the "Up" and "Down" buttons to select a language: English (default), German, Spanish,
French, Russian, or Chinese.
4. Press the "OK" button when finished programming to go back to the on-screen display menu.
1. While the monitor display is on, press the "Menu/Unlock" button to open the on-screen display.
2. Highlight the "Setup" icon and press the "OK" button to enter the "Setup" screen.
3. Use the "Up" and "Down" buttons to select the advanced settings menu.
4. Press the "OK" button to enter the selected advanced settings menu.
Motion detection:
1. Select "Motion detection" and press the "OK" button.
2. Select "Off" or "On" to turn the PIR function off or on and press the "OK" button.
NOTE: If multiple cameras are paired to the monitor then select the desired camera.
3. The monitor will connect to the desired camera.
4. Press the "OK" button to confirm.
NOTE: A single beep from the camera indicates motion detection has been turned OFF.
A triple beep indicates motion detection has been turned ON.
Backlight time:
1. Select "Backlight time" and press the "OK" button.
2. Use the "Up" or "Down" buttons to select a backlight time between 10~60 seconds.
3. Press the "OK" button to confirm.