Enhanced Beverage Solutions Nitro Infuser-Dual User manual

© Enhanced Beverage Solutions | August 2019 | Revision 2.003 | Patent Pending
www.enhancedbeveragesolutions.com | @enhancedbeveragesolutions | #TapCulture
INSTALLATION INSTRUCTIONS
Continued...
-DUAL
Step 1: Preparation
If you are installing your Nitro Infuser in an existing system, the nitrogen gas must be shut o and the system depressurized,
including the kegs. Set the regulator to 0 psi. Open the tap faucet to release pressure.
Step 2: Identify Mounting Location for Nitro Infuser
The Nitro Infuser will be mounted within the kegerator, on the tap lines from the kegs to the tap faucets. Placement of your Nitro
Infuser on the inside wall of the kegerator near the top is ideal. For best performance, the Output lines to the faucet should be as
short as possible.
*Please note, infusing a beverage with nitrogen causes the liquid to freeze faster. To prevent freezing, install your infuser further
from the cooling mechanism (typically found near the back of the kegerator) and turn temperature up to approximately 33.5°F or
higher. Refer to your kegerator’s manual to ensure there is no electricity or cooling element behind selected location.
Thank you for purchasing a Nitro Infuser Dual!
Follow the instructions below to get started.
Installation videos and manuals may be found at:
www.enhancedbeveragesolutions.com/support
Beverage
Keg
Nitrogen
Gas
28 psi
Beverage
Keg B
Kegerator
Stout Faucet
Beverage
Keg A
T
To Faucet
To Faucet
T
Provided T Fitting
Provided T
Fitting
Gas B
Gas A
Beverage A
Beverage B
Output A
Output B
NCS
NCS
*Barbs on Nitro Infuser are permanently axed and not designed to be removed.
REMOVAL OF BARBS VOIDS WARRANTY

-DUAL
Step 4: Beverage Lines
4 a) Identify the Beverage A line from Keg A to the tap/faucet. Cut the line at a point that will t the Nitro Infuser mounting location.
4 b) Connect the Beverage A tap line from the faucet to the Nitro Infuser line labeled “Output A”. Secure with hose clamp.
4 c) Connect the Beverage A keg out line to the Nitro Infuser line labeled “Beverage A”. Secure with hose clamp.
4 d) Repeat steps 4 a) - 4 c) to connect Beverage B line to the Nitro Infuser.
Step 5: Mount Nitro Infuser to Keg System
5 a) Once all connections are complete, double-check connections to assure hose clamps have been tightened.
5 b) Attach Nitro Infuser to kegerator in desired location from Step 2.
Step 6: Pressurizing System
6 a) Keep tap faucet in the closed position.
6 b) Turn the nitrogen gas cylinder to a full open position.
6 c) Adjust gas regulator to 28 psi - please note that if the regulator is set to higher than 28 psi you will need to release pressure
from coee keg once regulator is adjusted to 28 psi.
6 d) You will hear nitrogen gas pressurizing the keg for a short time. Check every connection for any gas or leaks. It is important to
Step 7: Adjusting Your Nitro Infuser
7 a) Start with the Nitrogen Control System (NCS) valve all the way closed and pour a drink.
7 b) Open NCS valve one full turn. Pour and analyze infusion level. Adjust accordingly open or closed one quarter turn at a time.
7 c) Once the desired infusion level is found, lock in the NCS by tightening the hex nut against the NCS.
Step 3: Nitrogen Gas Lines
*It is important to make sure your gas system is turned o until the install is complete*
3 a) Using one of the provided T ttings, connect one side to the rst gas line coming from your dual regulator. Secure with hose
clamp.
3 b) Connect another side of the T to one of the provided hoses. Secure with hose clamp. Connect the other end of the hose to
the “gas in” connection on your keg. Secure with hose clamp.
3 c) Connect the last side of the T to the second provided hose. Secure with hose clamp. Connect the other end of the hose to
the Nitro Infuser, on one of the barbs labeled “Gas”. Secure with hose clamp.
3 d) Repeat steps 3 a) - c) with the second T tting, connecting the second gas line from the dual regulator to the second keg
and the Nitro Infuser.
© Enhanced Beverage Solutions | August 2019 | Revision 2.003 | Patent Pending
www.enhancedbeveragesolutions.com | @enhancedbeveragesolutions | #TapCulture
CLEANING
Cleaning your tap lines will clean the infusion system. It is recommended that you clean your tap lines every 1-2 weeks.
It is recommended to remove your stout nozzle and rinse daily.
If you are in need of service or support, contact the Enhanced Beverage Solutions team:
[phone] or [email protected]
Installation videos and manuals may be found at
www.enhancedbeveragesolutions.com/support
SUPPORT