Envertech EVT300 User manual

Envertech EVT300 & EVT360 + EVB300 Quick Installation Guide
Please read and follow the safety and installation
instructions below. You can find and download the
instructions or other technical documents on our
website: www.envertec.com .
Components
Microinverter
Monitoring Device
Monitoring APP
EVT300 & EVT360 EnverBridge EnverView
PV
Module 60-cell / 72-cell module
AC
Extension
Cable
(Optional)
To connect the AC side
to the grid.
Three-wire cable:
AWG12 or above.
AC End
Cap To seal the end of unused AC cable.
Note: EnverView App version should be 2.6 and above and EVB300 firmware
version should be EVB300-E-N-001-14 and above.
Envertech EVT300 & EVT360 Microinverter Installation
1. Mount microinverters onto the rack
Mark out the estimated center of each PV module on the rack to facilitate locating
microinverters..
Mount all microinvertes under modules to avoid rain and sun, with the trademark
facing downward.
Please make sure that there are less than 20 units of EVT300, or 16 units of
EVT360 in each branch(12AWG).
2. Grounding
Microinverters and modules must be connected to the grounding conductor in
accordance with national standards.
Fix the grounding wire with screws to the microinverter’s grounding hole, so that
the grounding of microinverters can be realized.
3. Connect microinverter AC cables serially
Connect the AC connectors on both sides of microinverters in a hand-in-hand way.
4. Fastern AC cables
Fasten AC cables and grounding cables to the rack with cable ties.
5. Seal the unused connector of AC cable
Insert the end cap directly into the connector on the unused end, and check if it is
inserted in place.
6. Connect AC cable to the junction box
Connect AC cable to the input of the junction box.
7. Mount EnverBridge
Take out the power cord and connect it to the EVB300, Screw on the antenna. Wait 3
minutes till the EVB300 green light blink, you can start the operation after booting
EVB300.
1) Installation
Option 1: Ethernet Mode
Fix EVB300 at proper position in or
close to the distribution box;
2. Run the RJ45 cable and connect the
EVB300 to your router;
3. Put the EVB300 plug into the socket.
Option 2: Wireless mode
Fix EVB300
at proper position in or
close to the distribution box within the
range Wi-Fi signal.
Turn off the air switch and connect
EVB300’ s power cable to the air switch.
2) Wi-Fi configuration setting
a) Connect network whose name is as same as your monitor’s SN in your
cellphone.
b) Open EnverView and click Wi-Fi Setting.
Installation could only be implemented when the system is
disconnected from the grid, and the solar panel has been covered
or disconnected.

c) Click the magnifying glass icon.
Select the Wi-Fi monitor need to connect.
Enter the password, then click the OK button.
8. Prepare AC extension cable
1）Remove the skin of the two ends of the extension cable by y=40mm and
remove the skin of internal wires by x=14mm. Set the metal terminals onto
the open parts and clamp them to tighten the connection;
2）Connect one side of the extension cable to the junction box;
3）Connect the other side of the extension cable to the air switch.
9. Connect PV modules to microinverters
Mount the PV modules on top of microinverters;
Connect each PV module with the DC input cables of the microinverter.
10. Switch on the PV system
Ensure all connection is completed and then turn on the air switch.
11. Monitoring through EnverPortal
1) Register a new account. Visit www.envertecportal.com.Click Sign Up. Fill in
the account information to finish registration.
2) Add MI
Option 1. Use EnverView app to bind MI(In the account)
Step 1: Login your account on your mobile phone. Then go to“Settings”.
Step 2: Under “Device Management”, click “Add” and enter MI SN manually or click the QR
code icon on the right to scan the MI SN automatically.
Step 3: Click “Confirm”to finish adding the MI.
Note:
a. Please ensure that both EVB300 and your phone are in same router network.
b. There is one serial number in EVT300 or EVT360, please make sure both serial
numbers are added.
Option 2. Use EnverView app to bind MI (Local model)
Note: Please ensure that both EVB300 and your phone are in same router network.
Step 1: Launch EnverView app, enter Local Mode. Connect your EVB300.
Step 2: On EVB Overview page, enter Settings. Click Add MI you could choose enter MI
SN manually or click the grid icon to scan the MI SN automatically.
Y=40mmR
Y=14mmR

5
7
4
6
1
2
1
2
1
2
1
2
3
length 780 mm length 1025 mm length 1025 mm length 245 mm
6
7
4
5
8
1
2
1
2
1
2
1
2
3
length 780 mm length 1025 mm length 1025 mm length 245 mm
1
2
1
2
1
2
1
2
3
length 780 mm length 1025 mm length 1025 mm length 245 mm
1
2
1
2
1
2
1
2
3
length 780 mm length 1025 mm length 1025 mm length 245 mm
8
5
6
7
4
1
2
1
2
1
2
1
2
3
length 780 mm length 1025 mm length 1025 mm length 245 mm
1
2
1
2
1
2
1
2
3
length 780 mm length 1025 mm length 1025 mm length 245 mm
Or you can scan the bar code.
Step 3: Click confirm to finishAdding MI.
Option 3. Use Envertecportal to add MI
Step 1: Login www.envertecportal.com with the newly-registered account, go to”
Settings—Management”.
Step 2 : Click Add, then enter the SN of Monitor, click OK to finish adding monitor. :
Click “ + ” button behind the Monitor SN, then enter the SN of microinverter, click OK to
finish binding.
12. Attachment:
1) Single Phase installation
2) Three Phase installation
Unscrew the front cover with the complimentary hex screwdriver, then plug wires on each
phase into the corresponding connector of EVB300.