Enviro C-10365 User manual

BY: SHERWOOD INDUSTRIES LTD
OWNER’S MANUAL
This appliance may be installed in an after market permanently
located, manufactured (mobile) home, where not prohibited by
local codes.
This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible for use with other
gases, unless a certied kit is used.
WHAT TO DO IF YOU SMELL GAS
• Open windows/Extinguish any open ame.
• Do not try to light any appliance.
• Do not touch any electrical switch or use any phone in your
building.
• Immediately call your gas supplier from a neighbour’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re
department.
WARNING
If the information in this manual is not followed exactly, a re or explosion may
result causing property damage, personal injury or loss of life. Installation and
service must be performed by a qualied installer, service agency or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other Flammable vapours and liquids in the vicinity of
this or any other appliance.
EG40-070
Massachusetts installations (Warning): This product must be installed by a licensed
plumber or gas tter when installed within the Commonwealth of Massachusetts. Other
Massachusetts code requirements:-Flexible connector must not be longer than 36
inches, shut off valve must be a “T” handle gas cock, only direct vent sealed combustion
products are approved for bedroom/bathrooms, replace dampers must be removed or
welded in the open position prior to the installation of a replace insert or gas log.
EG40 DV
SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER,
PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:
• All ENVIRO gas-red appliances must be installed
in accordance with their instructions. Carefully read all
the instructions in this manual rst. Consult the building
authority having jurisdiction to determine the need for
a permit prior to commencing the installation.
• NOTE: Failure to follow these instructions could
cause a malfunction of the replace, which could
result in death, serious bodily injury, and/or property
damage.
• Failure to follow these instructions may also void
your re insurance and/or warranty.
GENERAL
• Installation and repair should be done by a
qualied service person. The appliance should
be inspected before the rst use and, annually
thereafter by a qualied service person. More frequent
cleaning may be required due to excessive lint from
carpeting, bedding material, etc. It is imperative the
control compartments, burners and circulating air
passageways of the appliance be kept clean.
• Due to high temperatures, the appliance should
be located out of high trafc areas and away from
furniture and draperies.
Children and adults should be alerted to the
hazards of high surface temperatures and
should stay away to avoid burns or clothing
ignition.
Young children should be carefully supervised
when they are in the same room as the
appliance.
FOR YOUR SAFETY
• Installation and service must be performed by a
qualied installer, service agency or gas supplier.
• This installation must conform to local codes or, in
the absence of local codes, to the current CAN/CGA-
B149 installation code (Canada) or National Fuel Gas
Code ANSI Z223.1.2 (USA).
• To prevent injury, do not allow anyone who is
unfamiliar with the stove to operate it.
• To prevent injury, if the pilot or pilot and
burners have gone out on their own, open the
glass door and wait 5 minutes to air out before
attempting to re-light the stove.
• Always keep the area around this appliance clear
of combustible material, gasoline and other ammable
liquids and vapours.
• This appliance should not be used as a drying
rack for clothing or for hanging Christmas stockings/
decorations.
• Due to the paint curing on the stove, a faint odor
and slight smoking will likely be noticed when the
stove is rst used. Open a window until the smoking
stops.
Always connect this gas stove to a vent system and
vent to the outside of the building envelope. Never
vent to another room or inside the building. Make sure
the specied vent pipe is used; properly sized and of
adequate height to provide sufcient draft. Inspect
the venting system annually for blockage and signs of
deterioration.
WARNING: Failure to position the parts in accordance
with the diagrams in this booklet, or failure to use only
parts specically approved with this appliance may
result in property damage or personal injury.
WARNING: Do not operate with the glass front
removed, cracked or broken. Replacement of the
glass must be done by a licensed or qualied service
person.
• Never use solid fuels such as wood, paper,
cardboard, coal, or any ammable liquids, etc., in this
appliance.
• Do not use this heater if any part has been under
water. Immediately call a qualied service technician
to inspect the heater and to replace any part of the
control or gas control systems that have been under
water.
• Do not abuse the glass by striking it or slamming
the door shut.
Safety Precautions
2

Table of Contents
3
Safety Precautions..........................................................................................2
Table of Contents...........................................................................................3
Codes And Approvals......................................................................................4
Specications.................................................................................................5
Dimensions........................................................................................5
Clearances to Combustibles.................................................................5
Preparation For Installation:................................................................5
Initial Installation...........................................................................................6
Vent Termination Restrictions..............................................................6
Vent Congurations.............................................................................7
Vent Restrictor Ring............................................................................7
Vent Parts..........................................................................................8
Planning Your Installation....................................................................9
Horizontal Installation.......................................................................10
Corner Installations...........................................................................12
Vertical Installation...........................................................................12
Cathedral Ceiling Installation.............................................................15
Freestanding Direct Vent Kit With Coupler...........................................15
Venting into a Class ‘A’ Chimney.........................................................18
Mobile Home Installation...................................................................18
Electrical Requirements.....................................................................19
Replacing The Blower........................................................................20
Adjusting The Venturies....................................................................20
Fuel Conversion................................................................................21
Gas Line Connection and Testing........................................................22
Secondary Installation...................................................................................23
Installation of Log Set and Embers.....................................................23
Operating Instructions..................................................................................25
Lighting Instructions.........................................................................25
Turning Gas Off To Appliance.............................................................25
Routine Maintenance and Service...................................................................26
Trouble Shooting..........................................................................................27
Parts List......................................................................................................28
Parts Diagram - Chassis................................................................................30
Parts Diagram - Gas Tray & Door..................................................................31
Warranty......................................................................................................32
Installation Data Sheet..................................................................................33

DIRECT VENT: This type is identied by the sufx DV. This appliance draws all of its air for
combustion from outside the dwelling, through a specially designed vent pipe system.
This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level.
In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas Association
guidelines which state: the sea level rated input of Gas Designed Appliances installed at elevations above 2000
feet (610 m) is to be reduced 4% for each 1000 feet (305 m) above sea level. Refer also to local authorities or
codes which have jurisdiction in your area regarding the de-rate guidelines.
In Canada: When the appliance is installed at elevations above 4500 feet (1372 m), the certied high altitude
rating shall be reduced at the rate of 4% for each additional 1000 feet (305 m).
• This appliance has been tested by INTERTEK (Warnock Hersey) and found to comply with the established
VENTED GAS FIREPLACE HEATER standards in CANADA and the USA as follows:
VENTED GAS FIREPLACE HEATER (EG40 DV NG/LPG)
TESTED TO: ANSI Z21.88a-2003/CSA 2.33a-2003 VENTED GAS FIREPLACE HEATERS
CAN/CGA 2.17-M91 GAS FIRED APPLIANCES FOR HIGH ALTITUDES
CSA P.4.1-02 TESTING METHOD FOR MEASURING ANNUAL FIREPLACE EFFICIENCY
This ENVIRO EG40 DV Fireplace:
• Has been certied for use with either natural or propane gases. (See rating label.)
• Is not for use with solid fuels.
• Is approved for bedroom or bed sitting room. (IN CANADA: must be installed with a listed wall thermostat. IN
USA: see current ANSI Z223.1 for installation instructions.)
• Must be installed in accordance with local codes. If none exist, use current installation code CAN/CGA B149 in
Canada or ANSI Z223.1/NFPA 54 in the USA.
• Must be properly connected to an approved venting system and not connected to a chimney ue serving a
separate solid-fuel burning appliance.
• Manufactured (mobile) home installation must be in accordance with the Manufactured
Home Construction and Safety Standard, UL 307B, Title 24 CFR, Part 3280 and/or
The Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A.
The unit must be bolted to the oor of the mobile home and must be electrically
grounded to the steel chassis.
• Are approved for installation on combustible materials (i.e. Wood, carpet or
linoleum).
• Is not approved for closet or recessed installations.
IMPORTANT NOTICE (Regarding rst re up): When the unit is turned on
for the rst time, it should be turned onto high without the fan on for the rst 4
hours. This will cure the paint, logs, gasket material and other products used in the
manufacturing process. It is advisable to open a window or door, as the unit will start
to smoke and can irritate some people. After the unit has gone through the rst burn
turn the unit off including the pilot, let the unit get cold then remove the glass door
and clean it with a good gas replace glass cleaner, available at your local ENVIRO
dealer.
4
Codes And Approvals

5
WARNING:
Operation of this heater when not connected to a properly installed and maintained venting system can result in
carbon monoxide (CO) poisoning and possible death.
Specifications
DIMENSIONS:

 

 
 
 

 
 
 
    
CLEARANCES TO COMBUSTIBLES:
A. Sidewall to unit 12 inches (30.5 cm)
B. Backwall to unit 4 inches (10.2 cm)
C. Corner to unit 2 inches (5.1 cm)
D. Combustibles to unit top 36 inches (91.4 cm)
E. Floor to unit 0 inches
F. Alcove maximum depth: 48 inches (121.9 cm)
• Locate a position where the ue system of the stove can
be properly installed without damaging the integrity of the
building; e.g. cutting a wall or ceiling joist.
• Check stove and ue system clearance requirements.
• Locate the stove where it can be accessed by a gas supply line.
• Locate the stove in a large and open room that is centrally located in the house. This will optimize heat circulation
and comfort.
• As the stove is equipped with a convection fan, ensure that an electrical outlet is within 6 feet. (1.8 m) of the
stove.
• The ow of combustion and ventilation air must not be obstructed.
CLEARANCES MUST BE SUFFICIENT TO ALLOW ACCESS FOR MAINTENANCE AND SERVICE.
PREPARATION FOR INSTALLATION:
• Remove the packaging from the appliance, and check to make sure there is no damage. If damage is found,
please report it to both the carrier and your dealer as soon as possible.
• Before beginning, carefully check the glass door and the log set
Figure 1: EG40 Exterior Dimensions.

 

 

 
Figure 2: Clearances to combustibles.

1 In accordance with the current CSA B149, Natural Gas and Propane Installation Code.
2 In accordance with the current ANSI Z223.1 NFPA 54, National Fuel Gas Code.
* These numbers are only estimates. Clearance in accordance with installation codes and the requirements of the gas supplier.
t A vent shall not terminate directly above a side walk or paved driveway that is located between two single family dwellings
and it serves both dwellings.
+ Permitted only if verandah, porch, deck, or balcony is fully open on a minimum of two sides beneath the oor.
NOTE: Venting terminals shall not be recessed into walls or siding.
Initial Installation
QUALIFIED INSTALLERS ONLY
VENT TERMINATION RESTRICTIONS:
A
A
DE
LB
C
F
B
B
B
JMK
G
H
I
Openable
Fixed
Closed
Openable Fixed
Closed
Termination Cap Air Supply Inlet Gas Meter
G
G
Restriction Zone
(Termination not allowed)
N
O
Figure 3: Exterior Vent Termination Locations, use in conjunction with Table 1.
Table 1: Exterior Vent Termination Locations, use in conjunction with Figure 3.
Letter Canadian Installation 1US Installation2Description
A 12 in (30 cm) Clearance above grade, verandah, porch, deck, or balcony.
B 12 in (30 cm) 9 in (23 cm) Clearance from window or door that may be opened.
C 12 in (30 cm)* Clearance from permanently closed window (to prevent
condensation).
D 24 in (60 cm)* Vertical clearance to ventilated soft located above the
terminal, within a horizontal distance of 2 ft (60 cm) from
center line of terminal.
E 18 in (45 cm)* Clearance to unventilated soft.
F 12 in (30 cm)* Clearance to outside corner.
G 12 in (30 cm)* Clearance to inside corner.
H 3 ft (91 cm) within a height of
15 ft (4.5 m) above the meter/
regulator assembly
3 ft (91 cm) within a height of
15 ft (4.5 m) above the meter/
regulator assembly*
Clearance to each side of center line extended above
meter/regulator assembly.
I 3 ft (91 cm) 3 ft (91 cm)* Radial clearance around service regulator vent outlet.
J 12 in (30 cm) 9 in (23 cm) Clearance to non-mechanical air supply inlet to building, or
the combustion air inlet to any other appliance.
K 6 ft (1.83 m) 3 ft (91 cm) above if within 10
ft (3 m) horizontally
Clearance to mechanical air supply inlet.
L 7 ft (2.13 m)t 7 ft (2.13 m)*t Clearance above paved sidewalk or paved driveway located
on public property.
M 12 in / 30 cm+12 in / 30 cm*+Clearance under verandah, porch, deck, or balcony.
N 12 in (30 cm)* Clearance horizontally to any surface (such as an exterior
wall) for vertical terminations.
O 12 in (30 cm) Clearance above roof line for vertical terminations.
6

Figure 5: Vent restrictor ring.
Initial Installation
QUALIFIED INSTALLERS ONLY
Figure 4. Possible Vent Congurations; Vertical
and Horizontal Terminations.
VENT CONFIGURATIONS:
Figures 4 shows the range of venting options, it shows
possible vent congurations if the unit is top vented,
for vertical and horizontal terminations, any layout that
remains within the shaded area is acceptable. Having the
fewest number of elbows is ideal, as they tend to disrupt
air movement. Using 45˚ elbows is preferable to using 90˚
elbows. Also, a shorter vent system will perform better than
a longer one.
NOTE: The total length of the vent pipes can not exceed
33 feet (10.1 m). Any combination of rise and run can be
used as long as it lays within the shaded area (a total of
three (3) 90° elbows or six (6) 45° elbows can be used).
In addition to what is shown, if a 90° elbow is used in the
horizontal plane, 3 feet (91.4 cm) must be subtracted from
the allowable horizontal run (for each 45° elbow, 1 feet
must be subtracted from the allowable horizontal run).
VENT RESTRICTOR RING:
A vent restrictor ring is supplied with each direct vent replace. This
restrictor ring is to be installed when the vertical chimney installation
is over 6 feet (1.83 m). Before the chimney is placed onto the stove,
place this vent restrictor ring into the 4 inch (10.2 cm) ue pipe (as
shown), once the vent restrictor ring has been installed, the vertical
sections of chimney can be installed.
7

8
VENT PARTS:
This replace have been tested and certied for use with SIMPSON DURAVENT TYPE GS PIPE FOR GAS STOVES.
SELKIRK DIRECT-TEMP SYSTEM SECURITY CHIMNEY’S “SECURE VENT DIRECT VENT SYSTEM” and SELKIRK
“DIRECT TEMP VENT SYSTEM” kits are available for horizontal venting. When using Simpson Duravent, it is
recommended that, before installation, a bead of RTV High Temperature Silicone should be applied to each outer
vent joint, and Mil-Pac to each inner joint. When planning an installation, it will be necessary to select the proper
length of vent pipe for the particular requirements.
A MINIMUM VERTICAL LENGTH OF 24” (61 cm) TO THE FIRST 90° ELBOW IS REQUIRED. WITH THIS
MINIMUM VERTICAL RISE, HORIZONTAL RUNS OF FROM 1 FOOT (30.5 cm) to 3 FEET (91.5 cm) ARE PERMITTED
TO REACH THE OUTSIDE VENT TERMINATION.
BEFORE BEGINNING THE INSTALLATION TAKE CARE TO ENSURE AN APPROPRIATE OUTSIDE LOCATION FOR THE
VENT TERMINATION CAN BE ACCOMMODATED. FOLLOW THE VENT LENGTH DIAGRAM PRECISELY.
VENTING TERMINALS CANNOT BE RECESSED INTO A WALL OR SIDING.
Simpson Duravent (SD), Selkirk (SEL), and Security Chimneys (SC), must state if galvanized or black wanted, PART NUMBERS:
SD SEL SC Description SD SEL SC Description
908 4DT-6 SV4L6 6” pipe length 911 11” to 14 5/8” pipe, adjustable
907 4DT-9 9” pipe length 4DT-AJ 4” to 10” pipe , adjustable
906 4DT-12 SV4L12 12” pipe length SV4LA12 1” to 12” pipe , adjustable
904 4DT-24 SV4L24 24” pipe length 943 4DT-AF6 Flashing, 0/12 to 6/12 roof pitch
903 4DT-36 SV4L36 36” pipe length 943S 4DT-AF12 Flashing, 7/12 to 12/12 roof pitch
902 4DT-48 SV4L48 48” pipe length SV4FA Flashing, 1/12 to 7/12 roof pitch
945 4DT-EL45 SV4EBR45 45° elbow, black SV4FB Flashing, 8/12 to 12/12 roof pitch
990 4DT-EL90 SV4EBR90 90° elbow, black 943F SV4F Flat ashing
950 4DT-VS SV4VS Vinyl siding standoff/sheild 980 4DT-VC SV4CGV Vertical termination
942 4DT-WT SV4RSN Wall thimble 991 4DT-HVC High wind vertical termination
941 4DT-CSS SV4CSB Cathedral Support Box 984 4DT-HC SV4CHC Horizontal square termination
981 4DT-ST36 SV4STC36 36” Snorkel Termination 985 4DT-HHC High wind horizontal termination
953 4DT-SC SV4FC Storm collar 978 4DT-VKC SV0FAK Vertical termination kit
963 4DT-FS SV4BF Fire stop 970 4DT-HKA SV0SHK Horizontal termination kit
SD: Basic Kit, SEL: Kit A, SC: Standard Kit
988 4DT-WS/B SV4BM Wall strap/support/band
971 4DT-HKB SV0SHK2 Horizontal termination kit
SD: Kit A, SEL: Kit B, SC: Kit
Initial Installation
QUALIFIED INSTALLERS ONLY
Table 2: Vent Pipe Types with Part Numbers.
For horizontal venting installations Sherwood Industries Ltd.’s DV Kit with Coupler (part# EC-061) can be used, refer
to “Initial Installation - Freestanding Direct Vent Kit with Coupler.”

Initial Installation
QUALIFIED INSTALLERS ONLY
Vertical
Termination
Storm Collar
Flashing
Round Support
Box/Wall Thimble
Ceiling Firestop
Pipelength
Pipelength
Cathedral Ceiling
Support Box
Pipelength
Round Support
Box/Wall Thimble
Pipelength
Horizontal
Termination
90° Elbow
PLANNING YOUR INSTALLATION:
When planning your installation, it will be necessary to select the proper length of vent pipe for your particular
requirements. It is important to note when passing through a wall, the maximum allowable wall thickness is
10 inches (25.4 cm), 1 inches (3.8 cm) clearance to combustibles must be maintained. Select the amount of
vertical rise desired for “vertical-to-horizontal” type installations. To determine the length of vent pipe required for
vertical installations, measure the distance from the appliance ue outlet to the ceiling, the ceiling thickness, the
vertical rise through the attic or second story, and allow for sufcient vent height above the roof line. For two story
applications, a re stop is required at each oor level. If an offset is needed in the attic, additional pipe and elbows
will be required. To connect the venting system to the appliance ue outlet, a twist-lock adapter is built into the
appliance at the factory. Refer to ‘Vent Conguration and Restrictor Settings’ for venting parameters.
Your total vent pipe length must be within the shaded area of Figure 4. If a 90° elbow is used in the horizontal
plane, 36” (91.4 cm) must be subtracted from the allowable horizontal run.
There are three (3) basic types of Direct Vent System installations. The two (2) types of installations are:
Figure 6: Common Horizontal Installation.
Figure 7: Common Vertical Installation.
9

10
HORIZONTAL INSTALLATION:
STEP 1. Set the appliance in the desired location. Check to determine if wall studs or roof rafters are in the way
when the venting system is attached. If this is the case, you may want to adjust the location of the
appliance.
STEP 2. Direct vent pipe and ttings are designed with special twist-lock connections. Assemble the desired
combination of black pipe and elbows to the appliance adapter with pipe seams oriented towards the wall
or oor, as much out of view as possible.
Place a bead of Mil-Pac on the
outer edge of the inner exhaust
pipe (non-ared end). Place a bead
of high temperature silicone on the
male edge of the outer pipe. Push
the pipe sections completely together,
then twist-lock one section clockwise
approximately  turn, until the two
sections are fully locked. The female
locking lugs will not be visible from the
outside, on black pipe. They may be
located by examining the inside of the
female ends as shown in Figure 8.
Notes:
(1) Twist-lock procedure: four indentations, located on the female end of the pipes and ttings, are designed to
slide straight onto the male ends of adjacent pipes and ttings, by orienting the four pipe indentations so they
match and slide into the four entry slots on the male end.
(2) Horizontal runs of vent pipe must be supported every three feet. Wall straps are available for this purpose, also
when running horizontal pipe minimum clearances to combustibles must be maintained; 2 inches (5.1 cm) at
top, 1 inches (3.8 cm) at sides, 1 inches (3.8 cm) at bottom.
STEP 3. With the pipe attached to the stove in the correct location, mark the wall for a 10” (25.4 cm) x 10” (25.4
cm) square hole (refer to Figure 9). The center of the square hole should match the center line of the
horizontal pipe. Cut and frame the 10” (25.4 cm) x 10” (25.4 cm) hole in the exterior wall where the
vent will be terminated. Refer to Figure 8. If the wall being penetrated is constructed of non-combustible
material i.e. masonry or concrete, a 7 inches (17.8 cm) hole is acceptable.
Sealant
Female
Locking
Lugs
Male
Locking
Lugs
Figure 8: Twist-Lock Connection
Initial Installation
QUALIFIED INSTALLERS ONLY
Woodscrews
Wall Thimble
Strap
Sheet metal
screws
Fold strap
here
11/4"
(3.2cm)
Figure 10: Installing Decorative Wall Thimble.




Figure 9: Wall Framing Hole for
Horizontal Installation.