enware BLUELINE BUB205NC User manual

Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: [phone] [e-mail]
I00285_Sep 18
BUB205NC
TYPE 45 UPRIGHT BUBBLER
BUB205NCBF
TYPE 45 UPRIGHT BUBBLER WITH BOTTLE FILLER
BUB224NC
TYPE 63 UPRIGHT BUBBLER
BUB224NCBF
TYPE 63 UPRIGHT BUBBLER WITH BOTTLE FILLER
BLUELINE™ BUBBLER
Installation Instructions
BUB219NC
T100 WALL MOUNTED BUBBLER
BUB219NCBF
T100 WALL MOUNTED BUBBLER WITH BOTTLE FILLER
FOR USE WITH POTABLE WATER ONLY

2 Call 1300 369 273 www.enware.com.au
technical information
installation instructions
BEFORE PROCEEDING WITH INSTALLATION
Ensure all supply lines are ushed thoroughly to remove
debris prior to the installaon of this product as per
AS/NZS 3500.1. Strainers (40 mesh) are recommended if
debris is an ongoing problem.
1. Ensure water lines have been thoroughly ushed and
are free of debris.
2. Fit the dress ring to the bubbler and engage the
an-rotaon pins in the pin-holes.
3. Screw the bubbler to the desired posion on the ½”
MI thread without sealant or thread tape and mark the
countersunk holes.
4. Remove the bubbler and drill holes to accept a suitable
countersunk screw or xing.
Note: the holes are oset to allow easy access of a
screwdriver
5. Seal thread using thread tape (or other approved
means) and screw the bubbler into posion with the
dress ring ed and an-rotaon pins engaged.
6. Turn water on and acvate the bubbler and bole ller
to bleed any air that may be trapped in the bubbler.
Check the connecon point for leaks. Fit screws to
secure the bubbler in place.
7. Acvate the bubbler and bole ller a number of
mes, the bubbler ow stream will sele to a height
50-100mm above the mouthguard and is now ready to
use.
57.5
10
100
26
130
200
180
110
85
22
33
16 55
10
5TYP
DEPTH)
SPACE FOR
CIRCUIT BOARD
(REQUIRES 30mm
COVER PLATE
OUTLINE
IMAGE 2
Bubbler Inlet Connecon 15mm (1/2" BSP)
Spring Loaded SBA (Spindle) 5/8” BSP
Recommended Working Pressure
Range
100 – 500 kPa
(Max. 500 kPa – AS3500)
Flow Rate (Drinking Fountain)
2 – 2.5 L/min approx.
with ow stream set
50mm above guard top
Recommended Operang
Temperature Range for Drinking
Fountains
5 – 30 °C
COMPLIANCE
Enware products must be installed in
accordance with the Plumbing Code of
Australia (PCA), AS/NZS3500 and the
manufacturer’s instrucons. Installaons
not complying with PCA, AS/NZS 3500 and
the manufacturer’s instrucons may void
the product and performance warranty
provisions.
This product must be installed and
commissioned by a qualied plumber.
57.5
10
100
26
130
200
180
110
85
22
33
16 55
10
5TYP
DEPTH)
SPACE FOR
CIRCUIT BOARD
(REQUIRES 30mm
COVER PLATE
OUTLINE
IMAGE 1

3 Call 1300 369 273 www.enware.com.au
components
spare parts
Handle Cap and Screw - Bubbler BUB378NC
Handle Cap and Screw - Bubbler and Bole Filler BUB378NCBF
Cartridge - Bubbler BUB260NC
Cartridge - Bubbler and Bole Filler BUB260NCBF
Mouth Guard BUB734NC
Spout Insert BUB258
Cap and Screw BUB400
22
Hob/Wall Penetration

4 Call 1300 369 273 www.enware.com.au
trouble shooting
PROBLEM CAUSE RECTIFICATION
Flow stream is unsteady or
too low
Water supply condions have
changed or are uctuang
Incorrect ow adjustment
Check that water pressure is between
100kPa and 500kPa.
Remove the bubbler outlet and/or bole
ller by removing the securing grubscrew
and pulling free.
Flush the bubbler thoroughly.
Disassemble the bubbler outlet and clean
any debris from the ow control, check
valve or gauze. Any damaged parts should
be replaced. Reassemble and test.
cleaning
Enware product should be cleaned with a so damp cloth using only mild liquid detergent or soap and water.
Do not use cleaning agents containing a corrosive acid, sourcing agent or solvent chemicals. Do not use cream
cleaners, as they are abrasive. Damage caused this way will not be covered by warranty.

product warranty for Australia Eecve 1 September 2014
Enware Australia Pty Limited (ACN 003 988 314)
(“we” or “us”) warrants that this product (also referred
to as “our goods”) will be free from all defects in
materials and workmanship for 24 months* from the
date of purchase. Our liability under this warranty is
limited at our opon to the repair or replacement of
the defecve product or part, the cost of repair of the
defecve product or part or the supply of an equivalent
product or part, in each case if we are sased the
loss or damage was due to a defect in the materials or
workmanship of the product or part. All products must
be installed in accordance with the manufacturer’s
instrucons, the PCA, and AS/NZS3500 including any
other applicable regulatory requirements.
exceptions
This warranty does not apply in respect of any damage
or loss due to or arising from:
a) Failure by you or any other person to follow any
instrucons for use (including instrucons and direcons
relang to the handling, storage, installaon, ng,
connecon, adjustment or repair of the product)
published or provided by us;
b) Failure by you or any other person responsible for the
ng, installaon or other work on the product to follow
or conform to applicable laws, standards and codes
(including the AS/NZ 3500 set of Standards, all applicable
State and Territory Plumbing Codes, the Plumbing Code
of Australia and direcons and requirements of local and
other statutory authories); or
c) Any act or circumstance beyond our control including
faulty installaon or connecon, accident, abnormal use,
acts of God, damage to buildings, other structures or
infrastructure and loss or damage during product transit
or transportaon.
making a claim
To make a claim under this warranty you must
nofy us in wring within 7 days of any alleged defect
in the product coming to your aenon and provide
us with proof of your purchase of the product and
completed the Online Product Service and Warranty
form at www.enware.com.au/product-service-enquiry
All nocaons and accompanying forms must be
sent to Enware Australia Pty Limited, 9 Endeavour Rd,
Caringbah NSW 2229. Contact can also be made by
calling 1300 369 273 or email ([e-mail]).
Your costs in making a claim under this warranty,
including all freight, collecon and delivery costs, are
to be borne and paid by you. We also reserve the right
at our cost to inspect any alleged defect in the product
wherever it is located or installed or on our premises.
*Condional warranty: Jumper Valve Tapware - 2 Years:
1 year parts and labour on the complete assembly then
a further 1 year parts only warranty is applicable
Ceramic Disc Cartridge Tapware - 10 Years: 10 Year
ceramic disc cartridges – parts only; 1 Year parts and
labour on complete assembly
Outlets - 1 Year parts & labour on complete assembly
other conditions
Except as provided or referred to in this document, we
accept no other or further liability for any damages
or loss (including indirect, consequenal or economic
loss) and whether arising in contract, tort or otherwise.
Any benets available to you under this warranty are in
addion to any non-excludable rights or remedies you
may have under applicable legislaon, including as a
“consumer” under the Australian Consumer Law. To that
extent you need to be aware that: Our goods come with
guarantees that cannot be excluded under the Australian
Consumer Law. You are entled to a replacement or
refund for a major failure and for compensaon for any
other reasonably foreseeable loss or damage. You are
also entled to have the goods repaired or replaced if
the goods fail to be of acceptable quality and the failure
does not amount to a major failure.