enware WaterMark CDF320DC User manual

Version: Nov 16
Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: 02 8536 4000 Fax: [phone]
CDF320DC
Barrier Free Hi-Lo Wall Mounted
Drinking Fountain with Chiller
CLEARANCE 305mm
MOUNTING FRAME
WIDTH 101.6mm
473
991
864
812
686
708
WASTE
729
SUPPLY
856
SUPPLY
835
WASTE
Product Code
CDF320DC Wall Mounted Hi-Lo Round Bowl Barrier Free
Drinking Fountain with Chiller
FEATURES
Drinking Fountain
• Polished chrome-plated brass
bubbler & push button
• Satin finish waste strainer
• Vandal-resistant bottom plate
• Special mounting plate
• Brushed Finish 18 gauge Type
304 Stainless Steel
• Removable lower panel for easy
installation
Chiller
• Provides up to 30l/hour of mains
pressure chilled water.
• Stainless steel storage tank and
pipework
• Louvered front ventilation panel
• Easy access for maintenance
• Environmentally friendly R134A
refrigerant
• Optional carbon filter available
A sophisticated stainless steel barrier-free split height drinking
fountain with stylish sculpted round bowls and under counter chiller
unit. Matching brushed finish back panel and vandal resistant
bottom plate.Bubbler and push button are polished chrome-plated
brass. Waste strainer has a satin finish.
Enware tapware must be installed in accordance with the provisions of AS/NZS3500 and any
relevant local regulations. Installations not complying with AS/NZS3500 may void the product
and performance warranty provisions.
Drinking Fountain
Inlet Connection ½” BSP Female
Minimum Supply Line Size ½”
Waste Water Outlet Connection 1-1/2” BSP (40mm) Male
Technical Information
Chiller
Flow Rate 30 lph
Refrigerant R134A
Power Supply 240V/50Hz
Power Connection 3 pin 7.5A Plug with 1.8m lead
Working Pressure Range 200 - 500 kPa
Dimensions 437H x 338W x 261D
This product is disability friendly, designed to the technical
requirements of the ADA (American Disability Act 2010
- Standards for Accessible Design), however it does not
comply in full with AS1428.2 1992
A
TS5200.105 WM-022628
IAPMO R&T OCEANA

Version: Nov 16
Call 1300 369 273
www.enware.com.au
Enware Australia Pty Limited
9 Endeavour Rd Caringbah NSW 2229 Australia
Ph: 02 8536 4000 Fax: [phone]
Barrier Free Hi-Lo Wall Mounted
Drinking Fountain with Chiller
NOTES
1. HOLD ROUGH-IN DIMENSIONS ±1/8” (3.2MM)
2. WHEN INSTALLING THIS UNIT. LOCAL STATE OR NATIONAL
CODES SHOULD BE ADHERED TO. FOR DIMENSIONS
(LOCATIONS), WASTE AND SUPPLY REQUIREMENTS OTHER
THAN SHOWN, DIMENSIONS MARKED * MUST BE ADHERED
TO ACCORDINGLY.
3. INSTALLER MUST PROVIDE TRAP FOR PROPER INSTALLATION
REFER TO 5874/VRK5874 OPERATION AND MAINTENANCE
MANUAL FOR PUSH BUTTON AND VALVE INSTALLATION/
MAINTENANCE INSTRUCTIONS.
INSERT 5/16”-18 PANEL INSERTS FROM OPPOSITE SIDE AT
LOCATIONS SHOWN BY DARKENED HOLES. COMBINATIONS
SHOWN ARE FOR USE WITH LOW FOUNTAIN ON THE RIGHT
AND THE HIGH FOUNTAIN ON THE LEFT. USE OPPOSITE HOLES
FOR HIGH ON RIGHTS AND LOW ON LEFT
COMBINATIONS SHOWN ARE FOR USE WITH LOW FOUNTAIN
ON THE RIGHT AND HIGH FOUNTAIN ON THE LEFT. USE
OPPOSITE HOLES FOR HIGH ON RIGHTS AND LOW ON LEFT
TO CHANGE FOUNTAIN MTG. SCREW LOCATIONS: FIRST
REMOVE SCREWS AND THEN SQUEEZE CLIPS ON NUT
RETAINER TO POP OUT. SNAP INTO NEW POSITIONS
AND REASSEMBLE SCREWS.
ALIGN HOLES IN CHILLER SUPPORT TRAY WITH HOLES IN
FRAME AND FASTEN WITH #10 SHEET METAL SCREWS
IMPORTANT: A L.H LOW (OPTIONAL) CONFIGURATION WILL
REQUIRE A DIFFERENT BACK PANEL AND THE WASTE AND
SUPPLY DIMENSIONS SHOWN (*) WILL BE REVERSED.