Elkay 4400BF User manual

PAGE 1
4400BF_FTN_A LK4400BF_FTN_A
1000003952 (Rev. B - 03/20)
Owners Manual
Model 4400BF
Floor Mount Tubular Bottle Filler Fountain
INSTALLER
4400BF Fountains are among the easiest to install Fountains on the market today.
To assure you install these models easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER
APPLICABLE CODES. After installation, leave these instructions with the Fountain for
future reference.

PAGE 2
4400BF_FTN_A LK4400BF_FTN_A
1000003952 (Rev. B - 03/20)
1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure. NOTE: Mounting
structure must be capable of supporting 300 lb. load on fountain.
2. Refer to rough-in for plumbing.
3. Install shut-o󰀨 valve on water supply. (Valve not furnished)
4. Locate and install fountain using 3/8" minimum fasteners. (Fasteners not furnished).
5. Prior to installing the Bottle Filler to the fountain, insert drain tube (Item # 4) by positioning the short end of drain pipe
through the mounting plate of bottle ller. Next, place the aesthetic collar (item # 15) onto the center mounting position of
the fountain ensuring the vertical edge of the collar is upright and the curved edge sits below the mounting surface. Mount
bottle ller to fountain with collar centered between the two pieces. Secure with supplied hardware.
6. Connect water supply and fountain drain. Water connection and drain must comply with local codes.
7. Turn on water supply and check all connections for leaks.
CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the
inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line
8. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/4" IPS. Contractor to supply waste trap and service stop valve in
accordance with local code.
9. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before being
connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor, color,
or sediment problems.
10. Connect fountain to supply line with a shut-o󰀨 valve and install a 3/8" unplated copper water line between the valve and
the fountain. Remove any burrs from outside of water line. Push the tubes straight into the ttings until they reach a positive
stop, approximately 3/4" (See Fig. 2). DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE
O-RINGS MAY RESULT.
INSTALLATION INSTRUCTIONS
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICALFEEDBACK INTOAFOUNTAIN, CREATINGAN ELECTROLYSIS
WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION
IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY
THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE
BUILDING PLUMBING SYSTEM.

PAGE 3
4400BF_FTN_A LK4400BF_FTN_A
1000003952 (Rev. B - 03/20)
LEGEND A = 3/8" O.D. UNPLATED COPPER TUBE CONNECT - SHUT OFF VALVE BY OTHERS B = ACCESS PANEL ( 8" X 10" )
B
B
A
O
14" 356mm
6 - Ø .500 HOLES EQUALLY SPACED ON A 12.00 B.C.
10" 254mm
O
3" 76mm
29 9/16" 750mm
64 1/16" 1627mm
44 1/16" 1119mm
14 9/16" 371mm
8" 203mm
30" 762mm
O
12" 305mm B.C.

PAGE 4
4400BF_FTN_A LK4400BF_FTN_A
1000003952 (Rev. B - 03/20)
ITEM
NO.
PART NO.
ITEMIZED PARTS LIST
DESCRIPTION
8
3
12
6, 14
1000003814*
45931C
1000003812*
66815C
75724C
98685C
98686C
98678C
98679C
98680C
98681C
1000003692
1000003693
98682C
1000003694
1000003695
98683C
97247C
1000005456
55996C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
NS
Cover - Round Plate
Outdoor Bottle Filler Drain Plug
Access Panel
Tube - Drain
Screw - 1/4"x20 x 3/4" LG. Pinned Torx
Kit - Hardware/Bolts/Nuts/Wshrs/Torx Screws
Kit - (BF) Waterway/Nipple/Gasket/Tubes/Ftgs
Kit - 1.0 GPM Regulator (BF Only)
Kit - Nozzle/Aerator/Gasket/Pin/Key
Kit - Aerator/Key
Kit - Blank Bottle Filler Trim
Kit - LK4400BF Bottle Filler Trim
Kit - 4400BF Bottle Filler Trim
Kit - Push Button w/Blank Nameplate
Kit - Push Button w/LK4400BF Nameplate
Kit - Push Button w/4400BF Nameplate
Kit - Drain Adapter/Gasket/Nut/Washer
Kit - VR Torx Screws/Bit
Aesthetic Collar
In-Line Strainer
3
FIG. 1 FIG. 2
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816
1333, BUTTERFIELD ROAD, DOWNERS GROVE, ILLINOIS 60515
*select color option to complete part number
*FINISH COLOR OPTIONS – Choose color option to
complete your model number, add as sux example:
4400BFEVG
Matte nish: Evergreen = EVG
Gloss nish:
Beige = BGE Gray = GRY Terracotta = TER
Black = BLK Orange = ORN White = WHT
Blue = BLU Purple = PUR Yellow = YLW
Brown = BRN Red = RED
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C
1/4” O.D. TUBE
WATER INLET
TO COOLER
3/8” O.D. TUBE CONNECT
COLD WATER SUPPLY
BUILDING WATER
INLET
NOTE: WATERFLOW
DIRECTION
SERVICE STOP
(NOT FURNISHED)
TROUBLESHOOTING AND MAINTENANCE
ACTUATION OF QUICK CONNECT WATER FITTINGS:
Fountain is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the tting, relieve
water pressure, push in on the gray collar while pulling on the tubing. (see Fig.2) To insert tubing, push tube straight into
tting until it reaches a positive stop, approximately 3/4".
6, 14
NS = Not Shown
REV. DESCRIPTION
MATERIAL:
SCALE: CH. BY: APPROVED BY:
DR. BY:
REL. ECN: DATE:
B
6400 PENN AVENUE SAVANNA, ILLINOIS 61074
MANUFACTURING CO.
TOLERANCES UNLESS OTHERWISE SPECIFIED:
This Print is the Property of ELKAY MANUFACTURING CO. and is
loaned subject to return upon demand and upon the express condition
that it is not to be used directly or indirectly without our permission for
purposes other than those for which it was furnished.
2 PLACE DECIMAL ± .03 1 PLACE METRIC ± .8 MM
3 PLACE DECIMAL ± .005 2 PLACE METRIC ± .1 MM
ANGLES ±.50°
FOR REVISIONS
SEE SHEET 1 OF 10
SHEET 5 OF 10
SEE SHEET 1 OF 10
4420BFDB TUBULAR BI-LEVEL FOUNTAIN
1 : 8
CGK
CGK
D
21
27
38
62
31
21
11 24
22
27
13
10
42
62
49
30
10
13
42
62
61
28
63
20
29
6 SEE NOTE 13
58
78SEE NOTE 11
20
28
3748
21
16 59
10
13
1659
52 OR
33
25
43
43
43
61
16
3SEE NOTE 5
34
32 45
33 45
63
29 22 24
24
11
11
37
3748
48
52 OR
22
20
29
28
63
61
45
8SEE NOTE 13
NCR-02488
RDZ
5/1/17
ASY99052C
61
62
61
62
61
62
61
59
5, 6
7
71
6
7
10
6
4
13
2
15
9
11