Sunnydaze Decor LZH-216 User manual

This fountain is intended for outdoor use only.
Place your fountain in a location where any water spills or splashing will not reach
any other electrical equipment or cause damage.
Choose an appropriate location before installing the fountain. DO NOT lift or push/drag the water
basin to relocate the fountain when it’s filled with water. Empty the water basin before lifting.
Excessive weight or pressure on any of the fountain sections may cause it to tip or fall over.
Keep pets and children away from any of the fountain sections.
Some splashing may occur. To avoid injury from electrical shock, observe basic safety precautions
and comply with the following instructions:
The pump on your fountain has no user serviceable parts. Only an authorized service representative .
should service the pump. Do not open the sealed pump housing as this may result in electrical shock
Refer to enclosed pump maintenance guide for cleaning.
3. An adult should supervise children when they are around the pump.
7. If any leakage occurs around the pump housing, turn off the circuit breaker immediately and have the pump serviced by
a registered technician.
remove the plug from the wall outlet until the circuit breaker is turned off.
NOTE: Allow the pump power cord to hang at a lower level than the wall outlet to form a “drip loop
”. This will help prevent water from dripping down the power cord and getting into the wall outlet.
(e.g. lights) from the outlet when not in use and before cleaning or replacing parts.
debris with a damp cloth if necessary.
TROUBLESHOOTING
1. If your FOUNTAIN PUMP fails to operate please check the following:
a) Make sure the pump is plugged into the socket properly.
b) Check the water level in the fountain. Running the pump without sufficient water can damage the pump.
c) Check the setting of the flow control on the pump. Check the pump outlet nozzle and the water tube for dirt and debris.
Clean if necessary.
d) Make sure the pump is connected to the water tube tightly. Check the fountain tubing for kinks and obstructions
e) The pump may be "air locked". Plug and unplug the pump several times to clear any air that may have been trapped.
2. If the water does not flow out of the fountain, it may be caused by kinked or loose water tubes, make sure water tubes
19" Solar Garden Water Fountain(LZH-216)
1. Install the fountain pump correctly before operating it.
2. DO NOT allow the pump to run dry.
13. Do not expose the pump to direct sunlight or to low temperatures for any period of time.
12. Periodically change the water. Clean the fountain water basin, the pump’s outlet nozzle and the water tube for dirt and
4. Use the proper power source as indicated on the pump label.
5. Equip the electrical power for the pump with a ground fault circuit interrupter (GFCI).
6. If the entire fountain falls into the water accidentally, turn off the circuit breaker immediately.
8. Do not operate the fountain if the pump has been dropped or has a damaged power cord or plug.
SAFETY PRECAUTIONS
14. Keep the power cord away from high temperatures or heat sources.
15. Use only a UL-approved extension cord of the correct rating to avoid overheating
9. If the plug or your wall receptacle gets wet due to water dripping down the power cord or for any other reason, do not
10. Always unplug the fountain pump and any other independent electrical accessories
11. Disconnect the power cord from the outlet by holding the plug, not by pulling on the power cord.

are connected properly.
ASSEMBLY PICTURES
ASSEMBLY INSTRUCTIONS
DO NOT allow the pump to run dry!
Be careful not to spill water onto the plug of the pump.
Fig 1
Fig 2
Step 1: Place the base on a level surface.pls refer to fig.1
Step 2: Insert the topper to the base.pls refer to fig.2
step 3:Lay the pump in the second base,connect the pump to the water tube,make sure the connection is tight,pls
refer to fig.3
step 4:Put the solar panel on the topper,make sure the wire of solar panel would throught the small hole of the
topper base,connect the solar panel wire to the wire of pump,make sure the connection is tight,pls refer to fig.4
Fig4
Fig 3