ep MosicGo Series User manual

Projector
User’s
TM
MosicGO
Guide
MOVIES MUSIC POWER GO
SINCE 2017
Printed in Taiwan
www.eliteprojector.com
FBZZ-MG1Z002-01
Model: Sport MGFU-S
Lite MGFU-L
Electronic file link
www.eliteprojector.com/MGFU/manual
TM
MosicGO
M

1
Electronic file link
www.eliteprojector.com/MGFU/manual Printed in Taiwan
www.eliteprojector.com
FBZZ-MG1Z002-01
1. The ventilation ports prevent overheating. Never block these ports located on the sides and bottom of the projector.
(See page 12) Direct obstruction, confined spaces or placing on a cluttered surface restricts airflow, and ruins the projector.
2. To reduce risk of fire or electric shock, do not expose the projector to any liquids, rain, snow or airborne moisture.
3. Do not insta
4. Do not use the projector in direct sunlight.
5.
6. Do not use the projector in areas susceptible to excessive dust and dirt.
7. Turn off the product before cleaning.
8. Disconnect the power cord if the product is not being used for a long period of time.
9. Ensure that the ambient room temperature is within 0- 40°C (32-104°F).
10. Ensure that relative humidity is 5 - 35°C (41- 95°F), 80% (Max.), non-condensing.
11. Do not drop, throw or try to bend your product.
explosion.
13. Clean only with dry cloth.
14. Only use attachments/accessori
15. Do not use the unit if it has been physically damaged or abused. Physical damage/abuse would be (but not limited to):
Unit has been dropped.
Charger or plug has been damaged.
Liquid has been spilled on the projector.
Projector has been exposed to rain or moisture.
Something has fallen into the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers may expose you to dangerous voltages or other hazards. Please contact your
local reseller or service center before you send the unit for repair.
17. Follow all warnings and cautions in this manual and on the projector.
18. The unit should only be repaired by appropriate service personnel.
19. Projector lamps generate a lot of heat. This causes much of the projector's surface area to heat up. If the projector seems to be excessively hot,
turn it off so that it can cool down and then call customer service.
EYE SAFETY WARNINGS
IMPORTANT SAFETY INSTRUCTIONS
To avoid retinal damage, do not stare directly or indirectly into the projector's light beam.
Rather than stand in the projector's light beam to point on the screen, use a laser pointer or pointer stick instead.
Make sure that students and other viewers observe the eye safety warnings and stay out of the direct light beam.
Use window blinds and turn down interior light sources to reduce the washout glare of ambient light.
COPYRIGHT / TRADEMARK
© Copyright 2019. All rights reserved.
The manufacturer reserves the right to make technical changes. The manufacturer assumes no liability for damages incurred directly or indirectly from errors,
omissions, or discrepancies between the device and this documentation.
Other brands or logos are trademarks or registered trademarks of their respective companies.
CAUTION – RISK OF BATTERY EXPLOSION IF INCORRECT TYPE IS USED
MAKE SURE TO PROPERLY DISCARD USED BATTERIES ACCORDING TO
LOCAL REGULATIONS

2
DECLARATION OF CONFORMITY
TRADEMARKS
FCC WARNING
AGENCY APPROVALS
Apple, Macintosh, iPod, iPod nano, and iPhone are trademarks or registered trademarks of Apple Computer, Inc. IBM is a trademark or registered trademark
2014/30/EU
EN 301489-1
EN 301489-17
EN 55032
EN 55024
Low Voltage Directive : 2014/35/EU
Safety: EN 62368 , EN62133+Annex.M
Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered
trademarks of Adobe Systems Incorporated.
household waste in all EU member states. Please follow the guidance of your local environmental authority or ask the shop where you purchased
the product for collection or recycling options.
(2) this device must accept any interference received, including interference that may cause undesired operation.
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Changes or modifications not expressly approved may void authority to operate the equipment.
FCC, CE, and LVD
Other specific Country Approvals may apply. Please see product certification label.
Product offerings and specifications may be altered at any time without notice.
6.3
Electronic file link
www.eliteprojector.com/MGFU/manual Printed in Taiwan
www.eliteprojector.com
FBZZ-MG1Z002-01
FCC CAUTION
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment
The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.

PRODUCT OVERVIEW
Kensington Lock Slot
Ventilation Port
USB POWER OUT
USB
12V Trigger Out
DC IN 19V
Power On/O Switch
USB Type C Display Port
(DP)
HDMI 2
HDMI 1
Earphone Jack
Touch
Focus
Ventilation Port
Tripod Mount Hole
Bluetooth
Projector
Bluetooth On /O Button
20.
Projector On /O Button
Battery / Power Status
3
1
25
7
8
13
12
9
10
11
16 17 18
6
4
14 15
19 20
*Note:
Follow the steps to open I/O cover.
(Battery indicator only for
MGFU-S model)
3
Electronic file link
www.eliteprojector.com/MGFU/manual Printed in Taiwan
www.eliteprojector.com
FBZZ-MG1Z002-01

1 2
DP
Remote Control
Menu
1. Bluetooth On/O
2. Projector On/O Brightness Adjustment (Note)
3.
Up (adjust keystone up)
4.
Left
5.
OK/Enter
6.
Right
7.
Down (adjust keystone down)
8.
Home
HDMI1
9. HDMI2
10. DP
Menu
11. Mute
12. Volume down
13. Volume up
14.
15. Video Source Search
16.
1. Up (adjust keystone up)
4. Left
3.
2. Down (adjust keystone down)
OK/Enter5.
Input Source Selection
6.
Home
7.
Right
Mute
8.
9.
Touch Keypad
PRODUCT OVERVIEW
6
1
4
1
3
6
8
11
12
14
7
4
2
5
7
2
5
10
9
13
15
16
3
8
9
4
Electronic file link
www.eliteprojector.com/MGFU/manual Printed in Taiwan
www.eliteprojector.com
FBZZ-MG1Z002-01
*Note:
When projector is off, short press PJ button on remote control to turn on projector.
When projector is ON, short pressing the PJ button on the remote control will cycle through
the following brightness modes: MAX, ECO, and MIN.
When projector is on, long press PJ button on remote control over 1 second , after prompt message
and then short press PJ button again to turn off projector.
When Bluetooth is off, short press BT button on remote control to turn on Bluetooth.
When Bluetooth is on, long press BT button on remote control over 1 second to turns off Bluetooth.

5
Connect the power cord to the
DC input jack.
Insert the plug into power
outlet.
1-A AC Adapt r
1-B Power Cord
1
3
2
4
5
7
6
3.
HDMI Cable x2
4.
USB Type C Cable
MGFU-S only
(*Note: only apply for
Sport MGFU-S model)
(*Note: Only Sport MGFU-S model has a battery pack)
4-A Remote Control
4-B Battery (AAAx2)
5.
6. 6-A HDMI SPLITTER
6-B 5V Power Cable
7. Carrying bag
User’s Guide (with Warranty Card)
PRODUCT ACCESSORIES LIST
POWER ON/OFF
1-A 1-B
4-B4-A
6-A 6-B
or
4.Press the Power On/Off Switch. The OK icon on the touch keypad will illuminate.
MosicGOTM has an internal battery pack.
Please fully charge the battery before using the projector.
3 .
Electronic file link
www.eliteprojector.com/MGFU/manual Printed in Taiwan
www.eliteprojector.com
FBZZ-MG1Z002-01
POWER
DC5V INPUT
OUTPOT2OUTPOT1
MOSICGO
SOURCES
TOUSB PORT
TOHDMI
Projector
User’s
TM
MosicGO
Guide
MOVIESMUSIC POWER GO
SINCE2017
PrintedinTaiw a n
www.eliteprojector.com
FBZZ-MG1Z002-01
Model:SportMGFU-S
LiteMGFU-L
Electronicfilelink
www.eliteprojector.com/MGFU/manual
TM
MosicGO
M
MOVIES MUSIC POWER GO
TM
MosicGO

BT SPEAKER / PROJECTOR ON/OFF
6
Electronic file link
www.eliteprojector.com/MGFU/manual Printed in Taiwan
www.eliteprojector.com
FBZZ-MG1Z002-01
BT SPEAKER / PROJECTOR ON/OFFBT SPEAKER / PROJECTOR ON/OFF
*Note:
Press the Bluetooth button / PJ button to turn off Bluetooth / projector before press power off switch.
Avoid press power off switch directly when projector / Bluetooth still on
18
19
7
7
*Note:
An audible tone sounds when the Bluetooth powers on/off,
or when the projector connects/disconnects to a device.
Press the Bluetooth button to activate this
feature.It’s blue LED lamp will flash when the
Bluetooth is in pairing mode. Check “MosicGOTM”
on your device to connect to MosicGOTM Bluetooth
. When device is connected successfully, the blue
LED lamp will light persistently.To turn off the
Bluetooth, press down and hold the BT button for
over 1 second.When both projector and Bluetooth
are ON, short pressing the Bluetooth button on
the remote control will switch audio source
between projector and Bluetooth.
Press the PJ button to turn the projector on and
the status LED indicator will light up. To turn off
the projector, press and hold the PJ button for
over 1 second. After seeing prompt message,
short press PJ button again to confirm. The
MosicGOTM logo will show briefly before the device
powers off.The status LED indicator light will be
flashing as the projector powers down.When
projector is ON, short pressing the PJ button on
the remote control will cycle through the following
brightness modes: MAX, ECO, and MIN.
1.
2.