EPA VFD-L series User manual

VFD-L Series User Manual
115V 200W-400W
230V 200W-2HP
Simple General Purpose AC Drive
EP ANTRIEBSTECHNIK GmbH
Fliederstraße 8 Postfach 1333
63486 Bruchköbel 63480 Bruchköbel
Telefon [phone]
Telefax [phone]
e-mail: [e-mail]
www.epa-antriebe.de
Änderungen und Irrtümer vorbehalten. / We reserve the right to changes without further notice.

1
Preface
Thank you for choosing EPA’s VFD-L series AC Drive. The VFD-L series is manufactured using
high-quality components, material and incorporating the latest microprocessor technology available.
This manual will help in the installation, parameter setting, troubleshooting, and daily maintenance of
the AC motor drive. To guarantee safe operation of the equipment, read the following safety
guidelines before connecting power to the AC motor drive. Keep this operating manual handy and
distribute to all users for reference.
Important Notes:
 DANGER! AC input power must be disconnected before any maintenance. Do not connect or
disconnect wires while power is applied to the circuit. Only qualified technicians should perform
maintenance on the VFD-L.
 CAUTION! There are highly sensitive MOS components on the printed circuit boards. These
components are especially sensitive to static electricity. To avoid damaging these components,
do not touch the circuit boards with metal objects or your bare hands.
 DANGER! A charge may still remain in the DC-link capacitor with hazardous voltages even
after the power has been turned off. To avoid personal injury, do not remove the cover of the AC
drive until all “DISPLAY LED” lights on the digital keypad are off. Please note that there are live
components exposed when the AC drive is open,. Be careful to not touch these live parts.
 CAUTION! Ground the VFD-L using the ground terminal. The grounding method must
comply with the laws of the country where the AC drive is to be installed.
 DANGER! The AC drive may be destroyed beyond repair if power is misapplied to the
input/output terminals. Never connect the AC drive output terminals U/T1, V/T2, W/T3 directly
to the AC main circuit power supply.

2
Chapter 1 Receiving and Inspection
This VFD-L AC drive has gone through rigorous quality control tests at the factory before shipment.
Since many things may happen during shipping, please check for the following after receiving the
AC motor drive.
◎Inspect the unit to insure it was not damaged during shipment.
◎Make sure that the part number indicated on the nameplate corresponds with the part number of
your order.
Nameplate Information: Example of 1HP230V
MODE :VFD007L21A
INPUT :1PH/9.7A 3PH/5.1A 200-240V 50-60Hz
OUTPUT :3PH 0-240V 4.2A 1.6kVA 1HP
Freq. Range:1.0~400Hz
MADE INXXXXX
007L21AT101001
AC Drive Model
Input Spec.
Output Spec.
Output Freq. Range
Bar Code
Serial NO.
Model Explanation:
VFD 007 L 21
A
version
A standard
B including EMI
：
：
Filter
VFD-L series
Input voltage
002:0.2kW
004:0.4kW
007:0.75kW
015:1.5kW
Applicable motor capacity
Variable Frequency Drive
Series Number Explanation:
T 10 0013
Production number
Production week
Production year 2003
Production factory
(T: Taoyuan, W: Wujuang)
If there is any nameplate information not corresponding to your purchase order or any problem,
please contact your distributor.

3
Dimension
RARC+10V AVIM0 M1M2M3GND
STOP
RUN
FWD
REV
RUN
STOP
PROG
DATA
MODE
RESET
Do not connect AC power to output
WARNING
Read the user manual before operation.
Do not inspect components until LEDs
are turned off for at least 1min.
terminals (U,V,W).
MIN. MAX.
VFD-L
RS- 485
V
I
230V IPHASE
0.75KW

4
Chapter 2 Wiring
Basic Wiring Diagram
Users must connect wiring according to the circuit diagram shown below. Please follow all National
and State wiring codes, when wiring the VFD-L.
U/T1
V/T2
W/T3
IM
3~
RS-485
61 ←
RA
RC 120VAC/28VDC 3A
010VDC
VR 3K 5K
〜
：〜Ω
AVI
GND
+10V 10mA(MAX)
3
2
1
VR
RJ-11 1:+EV
2:GND
3:SG-
4:SG+
R/L1
S/L2
T/L3
MCCB
+18V
+18V
+18V
M0
M1
M2
GND
+18V
4.7K Ω
M3
4.7K Ω
4.7K Ω
4.7K Ω
Factory default settings
Forward/Stop
Reverse/Stop
Reset
Multi-step 1
Common Signal
Power supply for Potentiometer
Master Freq. setting
Analog voltage
Analog current
Motor
Multi-function indication
output contacts
Factory default:
Fault Indication
Main circuit (power)
terminals
Control circuit terminals
Shielded leads
*If the AC Drive model is VFD002L11A/B, VFD004L11A/B, VFD002L21B, VFD004L21B
or VFD007L21B, please use power terminals R/L1 and S/L2.
*If the AC Drive model is VFD002L21A, VFD004L21A or VFD007L21A, 3 phase power
may be used on R/L1, S/L2, T/L3.
*If the AC Drive model is VFD015L23A, single phase power is not allowed.
NOTE: Do not plug in a Modem or telephone line to the RS-485 communication port,
permanent damage may result. Terminals 1 & 2 are the power source for the
optional copy keypad and should not be used while using RS-485
communication.
Main Circuit Power
Communication
port
+10V
R/L1
S/L2
T/L3

5
Main circuit wiring
Single phase models input from R/L1, S/L2
AC line input terminals
grounding
UP/DOWN
Function
Display key
Data
Confirmation key
RUN/STOP
RS485
communication
port
Grounding
Motor connections U/T1, V/T2, W/T3
Motor capacity
and input power
Frequency
setting knob
LED display
The signal selection
for AVI to input
DC0~+10V
or 4~20 mA
U/T1 V/T2 W/T3
R/L1 S/L2 T/L3
Control circuit wiring
RA RC +10V AVI M0 M1 M2 M3 GND
(120VAC/DC28V3A)
Relay
Wire Gauge:22-24AWG
Torque: 4Kgf-cm
Multi-functionindication
outputcontact
Powerforspeedsetting
AnalogVoltage,current
frequencycommand
Multi-functionassistantterminal
Commonsignal
Multi-functioninputselection1
Multi-functioninputselection2
Multi-functioninputselection3

6
Wiring Notes: PLEASE READ PRIOR TO INSTALLATION.
1. !CAUTION: Do not connect the AC input to any of the U/T1, V/T2, W/T3 terminals, as it will
damage the AC drive.
2. !WARNING: Ensure all screws are tightened to the proper torque rating.
3. During installation, follow all national and local electrical, construction, and safety codes for the
country the drive is to be installed in.
4. Ensure the appropriate protective devices (circuit breaker or fuses) are connected between the
power supply and AC drive.
5. Make sure that the leads are connected correctly and the AC drive is properly grounded. (Ground
resistance should not exceed 0.1Ω.)
6. Use ground leads that comply with AWG/MCM standards and keep them as short as possible.
7. Multiple VFD-L units can be installed in one location. All the units should be grounded directly to
a common ground terminal. The VFD-L ground terminals may also be connected in parallel, as
shown in the figure below. Ensure there are no ground loops.
Forward
running
8. When the AC drive output terminals U/T1, V/T2, and W/T3 are connected to the motor terminals
U, V, and W, respectively, the motor will rotate counterclockwise (as viewed from the shaft ends
of the motor) when a forward operation command is received. To reverse the direction of motor
rotation, switch over any of the two motor leads.
9. Make sure that the power is capable of supplying the correct voltage and required current to the
AC drive.
10.Do not attach or remove wiring when power is applied to the AC drive.
11.Do not monitor the signals on the circuit board while the AC drive is in operation.
12.Route the power and control wires separately, or orthogonal to each other.
13.If a filter is required for reducing EMI (Electro-Magnetic Interference), install it as close as
possible to AC drive. EMI can also be reduced by lowering the Carrier Frequency.
14.If the AC drive is installed in the place where a load reactor is needed, install the filter close to
U/T1, V/T2, W/T3 side of AC drive. Do not use a Capacitor or L-C Filter (Inductance-Capacitance)
or R-C Filter (Resistance-Capacitance).
15.When using a GFCI (Ground Fault Circuit Interrupt), select current sensor with minimum current
200mA, and minimum detection time 0.1-second to avoid nuisance tripping.

7
Chapter 3 Summary of Parameters
Group 0: User Parameters
aThe parameter may be set during operation.
Parameters Functions Settings Factory
Setting
0-00 Identity code of drive
(Read only)
1: 40W
2: 100W
3: 200W
4: 400W
5: 750W
6: 1.5KW
0-01 Rated current display
(Read only)
40W: 0.4A
100W: 0.8A
200W: 1.6A
400W: 2.5A
750W: 4.2A
1.5K: 7.0A
0-02 Parameter reset 10: Reset Parameters to Factory Setting 0
a0-03 Start-up display of AC
drive
0: F (Frequency command)
1: H (output frequency)
2: U (user-defined unit)
3: A (output current)
0
a0-04 User-defined Unit 0: Display User-Defined Unit (u)
1: Display Counter Value (C)
2: Display Process Operation (1=tt)
3: Display DC-BUS voltage (U)
4: Display output voltage (E)
0
a0-05 User-defined coefficient K 0.1 ~ 160 1.0
0-06 Software version Read only #.#
0-07 Password input 0 ~ 999 0
0-08 Password configuration 0 ~ 999 0
Group 1: Basic Parameters
Parameters Functions Settings Factory
Setting
1-00 Maximum operation Freq. 50.0 ~ 400Hz 60.0
1-01 Maximum setting Freq. 10.0 ~ 400Hz 60.0
1-02 Maximum output voltage 2.0 ~ 255V 220
1-03 Mid-point freq. 1.0 ~ 400Hz 1.0
1-04 Mid-point voltage 2.0 ~ 255V 12.0
1-05 Minimum output freq. 1.0 ~ 60.0Hz 1.0
1-06 Minimum output voltage 2.0 ~ 255V 12.0
1-07 Upper bound of freq. 1 ~ 110% 100
1-08 Lower bound of freq. 0 ~ 100% 0.0
a1-09 Accel time 1 (Tacc1) 0.1 ~ 600 Sec 10.0
a1-10 Decel time 1 (Tdec1) 0.1 ~ 600 Sec 10.0
a1-11 Accel time 2 0.1 ~ 600 Sec 10.0

8
Parameters Functions Settings Factory
Setting
a1-12 Decel time 2 0.1 ~ 600 Sec 10.0
a1-13 JOG Accel time 0.1 ~ 600 Sec 10.0
a1-14 JOG Decel time 0.0 ~ 600 Sec 10.0
a1-15 JOG frequency 1.0Hz~400Hz 6.0
1-16 Auto-accel/decel 0: Linear Accel/Decel
1: Auto accel, linear decel
2: Linear accel, auto decel,
3: Auto Accel/Decel
4: Linear accel. Auto decel, stall prevention
during deceleration
5: Auto accel. Auto decel, stall prevention
during deceleration
0
1-17
S-curve setting in
acceleration 0 ~ 7 0
1-18
S-curve setting in
deceleration 0 ~ 7 0
Group 2: Operation Method Parameters
Parameters Functions Settings Factory
Setting
2-00 Source of frequency
command
0: Digital keypad
1: 0 ~ 10V from AVI
2: 4 ~ 20mA from AVI
3: Controlled by V.R on drive
4: RS-485 communication interface
0
2-01 Source of operation
command
0: By digital keypad
1: By external terminals, keypad STOP
enable
2: By external terminals, keypad STOP
disable
3: By RS-485 communication interface, keypad
STOP enable
4: By RS-485 communication interface, keypad
STOP disable
0
2-02 Stop method 0: Ramp stop
1: Coast stop
0
2-03 Carrier freq. 3 ~10K Hz 10
2-04 Reverse operation inhibit 0: Enable reverse
1: Disable reverse
2: Disable forward
0
2-05 ACI (4 ~ 20mA)
input loss detection 0: Decel to 0Hz
1: Stop immediately, display EF
2: Run with the last freq.
0
2-06 Line Start Lockout 0: Enable
1: Disable
0

9
Group 3: Output Function Parameters
Parameters Functions Settings Factory
Setting
3-00 Desired freq. attained 1.0 ~ 400 Hz 1.0
3-01 Terminal count value 0 ~ 999 0
3-02 Preliminary count value 0 ~ 999 0
3-03 Multi-function (relay
output)
0: not used
1: AC drive operational
2: Max. Output Freq. Attained
3: Zero Speed
4: Over Torque
5: Base-Block (B.B.)
6: Low Voltage Detection
7: AC Drive Operation Mode
8: Fault Indication
9: Desired Freq. Attained
10: PLC Program Running
11: PLC Program Step Complete
12: PLC Program Complete
13: PLC Program Operation Pause
14: Terminal Count Value Attained
15: Preliminary Count Value Attained
16: Ready State Indicator
8
Group 4: Input Function Parameters
Parameters Functions Settings Factory
setting
a4-00 Potentiometer bias freq. 0.0〜350Hz 0.0
a4-01 Potentiometer bias
polarity 0: positive bias 1: negative bias 0
a4-02 Potentiometer freq. gain 1〜200％100
4-03 Potentiometer 0: not used
reverse motion 1: reverse motion enable 0
enable 2: forward motion only
4-04
Multi-function input
terminal1 (M1)
(d 0〜d 20)
1
4-05
Multi-function input
terminal 2(M2) 6
4-06
Multi-function input
terminal 3(M3) 7
(d 0, d 4〜d 20)
0: not used
1: M0: FWD/STOP, M1: REV/STOP
2: M0: RUN/STOP, M1: FWD/REV
3: M0, M1, M2: 3-wire operation control mode
4: External fault, normally open (N.O.)
5: External fault, normally closed (N.C.)
6: RESET
7: multi-step speed command 1
8: multi-step speed command 2
9: jog operation
10: accel/decel speed inhibit
11: first or second accel/decel time selection
12: base-block (B.B.),normally open (N.O.)
13: base-block (B.B.),normally closed (N.C)

10
Parameters Functions Settings Factory
setting
4-06 Multi-function input 7
terminal 3(M3)
(d 0, d 4〜d 20)
14: increase master freq.
15: decrease master freq.
16: run PLC program
17: pause PLC
18: counter trigger signal
19: counter reset
20: select ACI/deselect AVI
Group 5: Multi-step Speed and PLC Parameters
Parameters Functions Settings Factory
Setting
5-00 1st step speed freq. 0.0 ~ 400Hz 0.0
5-01 2nd step speed freq. 0.0 ~ 400Hz 0.0
5-02 3rd step speed freq. 0.0 ~ 400Hz 0.0
5-03 PLC mode 0: Disable PLC operation
1: Execute one program cycle
2: Continuously execute program cycles
3: Execute one program cycle step by step
(separate by STOP)
4: Continuously execute one program cycle step by
step (separate by STOP)
0
5-04 PLC forward/reverse
motion
0 ~ 15 (0: Forward 1: Reverse) 0
5-05 Time duration step 0 0 ~ 65500 Sec 0
5-06 Time duration step 1 0 ~ 65500 Sec 0
5-07 Time duration step 2 0 ~ 65500 Sec 0
5-08 Time duration step 3 0 ~ 65500 Sec 0
Group 6: Protection Parameters
Parameters Functions Settings Factory
Setting
6-00
Over-Voltage
Prevention Level
0:disable
350~410V 390
6-01 Over-current
Prevention Level
0: disable
20~200%
170
6-02 Over-torque
detection
0:disable
1:enable during constant speed operation and
continues until the continuous limit is reached.
2:enabled during constant speed operation and
halted after detection.
3:enabled during accel and continues before
continuous output time limit is reached.
4:enabled during accel and halted after over-torque
detection.
0
6-03
Over-torque
detection level 30 ~ 200% 150

11
Parameters Functions Settings Factory
Setting
6-04
Over-torque
detection time 0.1 ~ 10.0 Sec 0.1
6-05 Electronic thermal
overload relay
0: Not used
1: Act with standard motor
2: Act with special motor
0
6-06
Electronic thermal
characteristic 30~600 Sec 60
6-07 Present fault record
6-08
Second most recent
fault record
6-09
Third most recent
fault record
6-10
Forth most recent
fault record
6-11
Fifth most recent
fault record
6-12
Sixth most recent
fault record
0: No fault occurred
1: oc (over current)
2: ov (over voltage)
3: oH (over heat)
4: oL (over load)
5: oL1 (electronic thermal)
6: EF (external fault)
7: Reserved
8: Reserved
9: ocA (current exceed during acceleration)
10: ocd (current exceed during deceleration)
11: ocn (current exceed during steady state)
0
Group 7: Motor Parameters
Parameters Functions Settings Factory
Setting
a7-00 Motor rated current 30~120 % 85
a7-01 Motor no-load current 0 ~ 90 % 50
a7-02 Torque
compensation 0 ~ 10 1
a7-03 Slip compensation 0.0 ~ 10.0 0.0
Group 8: Special Parameters
Parameters Functions Settings Factory
Setting
8-00 DC braking voltage level 0 ~ 30% 0
8-01
DC braking time during
start-up 0.0 ~ 60.0 Sec 0.0
8-02
DC braking time during
stopping 0.0 ~ 60.0 Sec 0.0
8-03 Start-point for DC braking 0.0 ~ 400.0 Sec 0.0
8-04 Momentary power loss 0: Stop operation after momentary power
loss.
1: Continues after momentary power loss,
speed search starts with master freq.
2: Continues after momentary power loss,
speed search starts with min. output
freq.
0

12
Parameters Functions Settings Factory
Setting
8-05
Max. allowable power loss
time 0.3 ~ 5.0 Sec 2.0
8-06 B.B. time for speed search 0.3~5.0 Sec 0.5
8-07
Max. speed search current
level 30~200% 150
8-08 Skip freq. 1 upper bound 0.0~400 Hz 0.0
8-09 Skip freq. 1 lower bound 0.0~400 Hz 0.0
8-10 Skip freq. 2 upper bound 0.0~400 Hz 0.0
8-11 Skip freq. 2 lower bound 0.0~400 Hz 0.0
8-12 Skip freq. 3 upper bound 0.0~400 Hz 0.0
8-13 Skip freq. 3 lower bound 0.0~400 Hz 0.0
8-14 Auto restart after fault 0~10 0
8-15 AVR function 0: AVR function enable
1: AVR function disable
2: AVR function disable when decel
2
8-16 Dynamic braking voltage 350 ~ 450V 380
8-17 DC braking lower bound limit 0.0 ~ 400 Hz 0.0
Group 9: Communication Parameters
Parameters Functions Settings Factory
Setting
a9-00 Communication address 1 ~ 247 1
a9-01 Transmission speed 0: Baud rate 4800
1: Baud rate 9600
2: Baud rate 19200
1
a9-02 Transmission fault
treatment
0: Warn and continue running
1: Warn and ramp to stop
2: Warn and coasting stop
3: No warn and keep running
0
a9-03
Modbus communication
watchdog timer
0: Disable
1~20: 1 ~ 20 Sec
0
ASCII
mode
0: 7,N,2
1: 7,E,1
2: 7,O,1
3: 8,N,2
4: 8,E,1
5: 8,O,1
a9-04 Communication
protocol
RTU
mode
6: 8,N,2
7: 8,E,1
8: 8,O,1
0

13
CHAPTER 4 Troubleshooting and Fault Information
The VFD-L AC drive has a comprehensive fault diagnostic system that includes several different
alarms and fault messages. Once a fault is detected, the corresponding protective functions will be
activated. The following faults are displayed on the AC drive digital keypad. The six most recent
faults can be read on the digital keypad display by viewing Pr.6-07 to Pr.6-12.
NOTE: faults can be cleared by pressing the Reset key on the keypad or Input Terminal.
Common Problems and Solutions:
Fault
Name Fault Descriptions Corrective Actions
The AC drive detects an abnormal
increase in current.
1. Check whether the motors horsepower
corresponds to the AC drive output power.
2. Check the wiring connections between the
AC drive and motor for possible short circuits.
3. Increase the Acceleration time (Pr.1-09,
Pr.1-11).
4. Check for possible excessive loading
conditions at the motor.
5. If there are any abnormal conditions when
operating the AC drive after the short-circuit
is removed, the drive should be sent back to
manufacturer.
The AC drive detects that the DC bus
voltage has exceeded its maximum
allowable value.
1. Check whether the input voltage falls within
the rated AC drive input voltage.
2. Check for possible voltage transients.
3. Bus over-voltage may also be caused by
motor regeneration. Increase the decel time.
The AC drive temperature sensor
detects excessive heat.
1. Ensure that the ambient temperature falls
within the specified temperature range.
2. Make sure that the ventilation holes are not
obstructed.
3. Remove any foreign objects on the heat sink
and check for possible dirty heat-sink fins.
4. Provide enough spacing for adequate
ventilation.
The AC drive detects that the DC bus
voltage has fallen below its minimum
value.
Check whether the input voltage falls within the
rated AC drive’s input voltage.
Internal electronic overload trip
1. Check for possible motor overload.
2. Check electronic thermal overload setting.
3. Increase motor capacity.
4. Reduce the current level so that the drive
output current does not exceed the value set
by the Motor Rated Current Pr.7-00.
The external terminal EF-GND goes
from OFF to ON.
When external terminal EF-GND is closed, the
output will be turned off. (under N.O.E.F.)
Motor overload. Check the
parameter settings ( Pr.6-03 to
Pr.6-05)
1. Reduce the motor load.
2. Adjust the over-torque detection setting to an
appropriate setting.

14
Fault
Name Fault Descriptions Corrective Actions
Over-current during acceleration:
1. Short-circuit at motor output.
2. Torque boost too high.
3. Acceleration time too short.
4. AC drive output capacity is too
small.
1. Check for possible poor insulation at the
output line.
2. Decrease the torque boost setting in Pr.7-02.
3. Increase the acceleration time.
4. Replace with the AC drive with one that has a
higher output capacity (next HP size).
Over-current during deceleration:
1. Short-circuit at motor output.
2. Deceleration time too short.
3. AC drive output capacity is too
small.
1. Check for possible poor insulation at the
output line.
2. Increase the deceleration time.
3. Replace with the AC drive with one that has a
higher output capacity (next HP size).
Over-current during steady state
operation:
1. Short-circuit at motor output.
2
. Sudden increase in motor loading.
3. AC drive output capacity is too
small.
1. Check for possible poor insulation at the
output line.
2. Check for possible motor stall.
3. Replace with the AC drive with one that has a
higher output capacity (next HP size).
Internal memory IC can not be
programmed.
1. Switch off power supply.
2. Check whether the input voltage falls within
the rated AC drive input voltage.
3. Switch the AC drive back on.
Internal memory IC can not be read.
1. Check the connections between the main
control board and the power board.
2. Reset drive to factory defaults.
Drive’s internal circuitry abnormal.
1. Switch off power supply.
2. Check whether the input voltage falls within
the rated AC drive input voltage. Switch on
the AC drive.
Hardware protection failure Return to the factory.
Software protection failure Return to the factory.
Auto accel/decel failure Don’t use the function of auto acceleration/
deceleration.
Communication Error
1. Check the connection between the AC drive
and computer for loose wires.
2. Check if the communication protocol is
properly set.
External Base Block.
AC drive output is turned off.
1. When the external input terminal (B.B) is
active, the AC drive output will be turned off.
2. Disable this connection and the AC drive will
begin to work again.
The AC drive detects excessive drive
output current.
1. Check whether the motor is overloaded.
2. Reduce torque compensation setting as set in
Pr.7-02.
3. Increase the AC drive’s output capacity.
4. Note: The AC drive can withstand up to 150%
of the rated current for a maximum of 60
seconds.

15
Standard Specifications
Voltage Class 115V 230V
Model Number VFD-LA/B 002 004 002 004 007 015
Applicable Motor Output (kW) 0.2 0.4 0.2 0.4 0.7 1.5
Rated Output Capacity (KVA) 0.6 1.0 0.6 1.0 1.6 2.7
Rated Output Current (A) 1.6 2.5 1.6 2.5 4.2 7.0
Max. Output Voltage (V)
3-phase corresponds
to double input
voltage
Three-phase corresponds to input voltage
Output Rating
Rated Frequency (Hz) 1.0~400Hz
Rated Input Current (A) 6 9 4.9/1.9 6.5/2.7 9.7/5.1 Ì/9
Input voltage Tolerance Single phase
90~132V 50/60Hz
Single / 3-phase
180~264V 50/60Hz
3-phase
180~264V
50/60Hz
Power
Frequency tolerance ±5%
Control system SVPWM (Sinusoidal Pulse Width Modulation, carried frequency 3kHz~10kHz)
Output Frequency Resolution 0.1Hz
Torque Characteristics Including the auto-torque, auto-slip compensation, starting torque can be 150% at
5 Hz
Overload Endurance 150% of rated current for 1 minute
Accel/Decel Time 0.1~600Sec. (can be set individually)
V/F pattern V/F pattern adjustable
Control
Characteristics
Stall Prevention Level 20~200%, setting of Rated Current
Keypad Setting by ▲▼ keys or V.R
Frequency
Setting External Signal
Potentiometer-5KΩ/0.5W, DC 0 ~ +10V (input impedance 47KΩ), 4~20mA (output
impedance 250Ω), multi-function inputs1 to 3 (3steps, JOG, UP/DOWN
command), communication setting
Operation
Setting Keypad Setting by RUN//STOP keys
Signal External Signal M0,M1,M2,M3 can be combined to offer various modes of operation, RS-485
communication
p
ort
Multi-function Input Signal Multi-step selection 0 to 3, Jog, accel/decel inhibit, first/second accel/decel switch,
counter, PLC Operation, external Base Block (NC,NO) selection
Operating Characteristics
Multi-function Output Signal AC Drive Operating, Frequency Attained, Non-zero speed, Base Block, Fault
Indication, Local/Remote indication, PLC Operation indication.
Other Function
AVR, S-curve, Over-Voltage Stall Prevention, DC Braking, Fault Records,
Adjustable Carried Frequency, Starting Frequency Setting of DC Braking ,
Over-Current Stall Prevention, Momentary Power Loss restart, Reverse Inhibition,
Frequency Limits, Parameter Lock/Reset
Protection Over Voltage, Over Current, Under Voltage, Overload, Electronic thermal,
Overheating, Self-testing
Other Including EMI Filter
Cooling Forced air-cooling
Installation Location Altitude 1,000 m or below, keep from corrosive gasses, liquid and dust
Ambient Temperature -10℃-40℃(Non-Condensing and not frozen)
Storage Temperature -20℃to 60℃
Ambient Humidity Below 90%RH (non-condensing)
Environment
Vibration 9.80665m/s2(1G) less than 20Hz, 5.88m/s2 (0.6Gat) 20 to 50Hz