Epcom XMR Series User manual

User Manual for XMRCP4
For more information, please visit our website:www.syscom.mx
User Manual
XMRCP4
Multy Functions Control Panel

User Manual for XMRCP4
For more information, please visit our website:www. syscom.mx
1 Product Characteristic
1.1Overview
XMRCP4 is a control panel used for bus intelligent dispatch system. Adopted with 18 buttons, 7 inches
large screen display, it also integrates with features of SMS, reversing monitor and driver swipe card etc..
It is widely applied to domestic and overseas bus systems for its easy installation, powerful features and
convenient operation.
1.2Features
1.2.1 Control Panel
XMRCP4 controls MDVR via RS232 serial port and driver can setup MDVR on .
The function of XMRCP4 is similar to remote control. Besides, it also can setup the menu of XMRCP4.
1.2.2 Bus Station Announcer
It works with MDVR (supported only with firmware of bus station announcer version) to announce the
stations manually/ automatically.
1.2.3 Live View
Menu and video can be transmitted toXMRCP4 via pass through mode. XMRCP4 can setup the other functions
of MDVR, such as record and playback.
1.2.4 Reversing Live View
There is an AV aviation-din on XMRCP4, drivers can connect the camera with XMRCP4. It is not used for
or monitoring, but to view the reversing vehicle and other live view. Besides, there is a sensor
using to connect with I\O signal, which is to switch the pictures of camera.
1.2.5 Drivers Swipe Card
There is a built-in RFID module in XMRCP4, which is used for drivers to sign in and sign out. The information
will be uploaded to platform via MDVR network.
1.2.6 SMS and Voice Broadcast
Built-in 2 speakers(16Ω, 2w), they are used to broadcast messages and some prompts
1.2.7 Intercom
Connect with microphone and MDVR, it can realize the functions of speaking inside/outside of the
vehicle, IP connection and making calls.
XMRCP4
recording

1.3Product structure
1.3.1 Product appearance and size.
Front Panel of XMRCP4
Dimension of XMRCP4
1.3.2 Button Introduction
CP4 applies with 18 buttons, including 1-0 number buttons, 4 function buttons and 4 arrow buttons for
bus control andscheduling application.
a. When drivers press number
1-5
, it broadcasts the messages set before and if there is no message,
it would not broadcast anything. (Supported only with firmware of bus station announcer version)
Example : When drivers press 1, it broadcasts Please take care of your belongings.
b. When drivers press number6-0, it sends message set before, and if there is no message, it does
not send anything.
Example: When drivers press 9, it will send a message to request schedule. If it is done successfully,
the center will send a conformed message back and the bus station announcer will broadcasts it
automatically.
c. When drivers press Broadcast Again, the speaker will broadcast the the message again, or switch
the inside calling to outside calling, or interrupt outside calling.
Example : When it is live-view or menu interface, the screen will turn to the main interface after
drivers press Broadcast Again.
d. When drivers press Broadcast, the speaker will broadcast the next bus station information inside
andoutside of the vehicle.
User Manual for XMRCP4
For more information, please visit our website:www.syscom.mx

Example : If the speaker says we are arriving XX, and it will turn to we are leaving XX when
pressing Next Stop.
e. Press Enter to view system information and open the selected menu.
f. Press Exit to exit current interface and switch from the main interface to the live-view interface.
g. Press 【 】 to go left, exit the current status, switch the module, or interrupt the outside calling.
h. Press 【 】 and 【 】 to go up or down.
i. Press
【 】
to go right or stop the current broadcast.
1.3.3 Product Specification
Items Parameter Performance Index
Specifications of Screen
Size 7 Inches
Resolution 800*480
Aspect Ratio 16:9
Button and Screen Distribution Combined
Material
Panel Material 70%PC+30%ABS Engineering plastics
Button Material Silicone
Built-in Module
RFID Wipe Card Module 13.56 MHZ for driver to sign in and sign off.
Speaker Speaker(16Ω, 2W)x2
Interface
MDVR Interface Connects to Streamax MDVR
CAM Interface
Yellow 4PIN aviation-din connector, connects
to reversing camera
MIC Interface Connects to the driver microphone
SENSOR Interface
Yellow hanging line, reversing signal
detection port, high level effective. To monitor
control for reversing.
Button
Function Buttons
Restate / station announcer / Arrow Keys /
Confirmation / Exit
Number Buttons 0-9
Installation
Tile Installation Refer to mounting bracket.
Bracket Installation There are three brackets with hood.
Dimension 185mm×128mm×34.9mm
Operation Parameters Operating Voltage 12V
Performance
Parameters
Operating Current 200mA
Total Power Consumption 2.4W
Waterproof and Dustproof IP53
Operating Temperature -20~+70
Relative Humidity 8%~90%
User Manual for XMRCP4
For more information, please visit our website:www.syscom.mx

1.3.4 LCD Specification
LCD Parameters Performance Index Description
Screen Type LCD screen
Touch Type 4 wire resistor type
Size 7 inches
Resolution 800*480
Luminance 400cd/m2
Contrast Ratio 20.83402778
Under a suitable brightness
condition, the higher contrast, the
richer color levels
Response Time 10/15(Tr/Td) ms
The response time of the LCD to
the input signal
Visual Angle
70/70/50/70 (Typ.)(CR dot
10)(Left/Right/Up/Down)
Maximum Number of Display
Color
262K/16.7M(6bit/6bit+Dithe
ring)
Scale 16:9
Back-light Type White LED
1.3.5 Bracket Installation
XMRCP4 supports bracket installation, and there are three brackets to be chosen:
Suitable for relatively flat console Suitable for curved console
Suitable for hanging
User Manual for XMRCP4
For more information, please visit our website:www.syscom.mx

1.3.6 Interface
To ensure the waterproof, the external interface of XMRCP4 uses harness, which leads a bunch of buses
from XMRCP4, and then the joint distributes according to their functions, details are as following:
Definition：
Connector Name Function Definition
MDVR
Black 10PIN aviation-din male connector
connects to Streamax MDVR.
CAM
Yellow 4PIN aviation-din connector
connects to reversing camera.
MIC Connects to driver microphone.
SENSOR
Yellow hanging line, reversing signal
detection port, high level effective. For
reversing control.
User Manual for XMRCP4
For more information, please visit our website:www.syscom.mx

User Manual for CP4
For more information, please visit our website:www.en.streamaxtech.com
2 Product Performance
2.1Environmental Performance
Serial No. Experiment Items Test Methods
1 Low Temperature Operation
a. Test equipment applies to GB/T 2423.1—2008
b. Put into the cryogenic chamber at -20℃±2℃for 72
hours at 0.85 times rated voltage. During this time, cut
off the power for 1 hour and reconnect the power for 1
hour repeatedly until the end of the test.
2 Low Temperature Storage
a. Test equipment applies to GB/T 2423.1—2008
b. Put into the cryogenic chamber at -40℃±2℃for 8 hours
without power supply. Recover to normal temperature
after the test.
3 High Temperature Operation
a. Test equipment applies to GB/T 2423.2—2008
b. Put into the high temperature chamber at +70℃±2℃
for 72 hours at 1.25 times rated voltage. During this
time, cut off the power for 1 hour and reconnect the
power for 1 hour repeatedly until the end of the test.
4 High Temperature Storage
a. Test equipment applies to GB/T 2423.2—2008
b. Put into the high temperature chamber at +85℃±2℃
for 8 hours without power supply. Recover to normal
temperature after the test.
5 Temperature Shock
a. Test equipment applies to GB/T 2423.1—2008 and
GB/T 2423.2—2008
b. Test cycles with the following procedures without power
supply for 24 hours:
——Keep -40℃±2℃for 2 hours;
——Keep -40℃±2℃for 1 hour;
——Keep +85℃±2℃for 2 hours;
——Keep +85℃±2℃for 1 hour;
——Keep +23℃±5℃for 2 hours.
6 Steady Damp-Heat
Test equipment applies to GB/T 2423.3—2006
Keep for 24hours at +40℃±2℃, 90%～95%
non-condensing without power supply.

2.2 Mechanical Environmental Performance
Serial No. Experiment Items Test methods
1 Impact
a. Test equipmentand method apply to GB/T 2423.5—2008
b. Normal installation and without power supply, the peak
acceleration is 490 m/s² and pulse duration is 11 ms. Six sides
do these steps 3 times.
2 Vibration
a. Test equipmentand method apply to GB/T 2423.10—2008
b. Normal installation and without power supply, the vibration
frequency is 5 Hz ~ 300 Hz and scanning speed is 1 otc/min.
In 5 Hz ~ 11 Hz frequency range, the amplitude is 10 mm. In
11 Hz ~ 300 Hz frequency range, the vibration acceleration is
50 m/s². On X, Y, Z three mutually perpendicular axis, each
axial does it for 8 hours.
3 Crash
a. Test equipmentand method apply to GB/T 2423.6—1995
b. Without power supply and any external protections, Peak
acceleration is 150 m/s², rated pulse duration is 6 ms. Per
direction collision is100±5 times
4 Drop
a. Test equipmentand methods apply to GB/T 2423.8—1995
b. Without power supply and any external protections, it falls
from 500 mm height
User Manual for XMRCP4
For more information, please visit our website:www.syscom.mx