Hanil Supra R22 User manual

Quick Guide Supra R22 / Supra R12
Cat. No. : SU-R22 / SU-R12
Display & Control Panel
Pulse
PULSE
xg
VIEW
SETTINGS
Start Stop
Display Screen
Status of RPM / RCF / Time /
Temperature / Rotor ID /
ACC / DEC / Program
Setting Speed
Press once : Setting RPM
Press twice : Setting RCF
Setting Time
Up to < 100 hr
Continuous run (00:00)
Lid Open
Program Save / Call
Saving a program
(up to 100)
Calling up a program
Setting the Rotor ID manually
When rotor id is not identified
automatically, enter the rotor ID.
manually
Max. RPM : 22,000 rpm
Max. RCF : 57,358 xg
Max. RPM : 12,000 rpm
Max. RCF : 22,265 xg
Supra R12
Supra R22
Press the
Pulse button
Enter the desired speed
(See ‘Setting Run
Parameters’)
Serial No. Installation Date
Saving / Calling Up a Program
Press a parameter
to be changed
Press the
Enter button
Enter the desired values
on the keypad
Enter the desired
program number on
the keypad
Press the
Save or call button
Setting Run Parameters
(RPM / RCF / Time / Temperature / ACC / DEC)
Press the
Enter button
Press the
Temp. limit button
Press the
Enter button
Temperature range that stops operation when the temperature
is lower or higher than the set temperature.
Enter the desired
temperature range
on the keypad
Setting Temp. Limit
View Settings
Verifying the setting
parameters during
centrifugation
Pulse
After reaching the set
speed, the centrifugation
is decelated and stopped
Setting ACC / DEC Rate
ACC (0 ~ 9 steps, Max.9)
DEC (0 ~ 9 steps, Natural DEC.0)
Setting Temperature
Setting temperature ( -10℃ ~ 40℃)
Setting temp. limit
2 31
5 64
8 97
0
±

Connect the device to voltage
sources, which correspond to the
electrical requirements on the label
attached to the device.
Check the wall outlet is earth-
grounded, surge-protected and
can supply enough power.
Connect the power cable to the
distribution box, or install the plug
and socket that are packed with
the device.
Switch off the device after use.
Unplug the power plug before
cleaning or unused for a long
period of time.
Check the Line Voltage Grounded Outlet Power Connection Switch Off the Device
Quick Guide Supra R22 / Supra R12
Cat. No. : SU-R22 / SU-R12
Maintenance
Electrical safety
A2.0-36
A10-12
A15-12
A15c-12
A50-6
A50c-6
36 x 1.5/2.0 mL / Max. 18k
12 x 10 mL / Max. 22k
12x 15 mL / Max. 22k
12 x 15 mL conical / Max. 17k
6 x 50 mL / Max. 22k
6 x 50 mLconical / Max. 17k
6 x 250 mL / Max. 12k
6 x 500 mL / Max. 10k
4 x 1,000 mL / Max. 8k
6 x 1,000 mL / Max. 7k
A250-6
A500-6
A1000-4
A1000-6
Rotors
Allow a safety clearance of 30 cm
around the centrifuge during
operation.
Remove Dust Empty the Condensation WaterAllow a Safety Clearance of 30 cmEmergency Lid Open
30 cm
30 cm
30 cm
If the centrifuge lid cannot be opened, insert the
provided T-wrench into the emergency release
hole on the right side of the device and press it.
(Before activating emergency open, switch off
the device and wait for the rotor to stop.)
Remove any dust from the
ventilation slits on the right side
of the device.
Empty the condensation water
regularly by removing the drain cap
on the left side of the device.
8 x 50 mL / Max. 20k
6 x 85 mL / Max. 20k
6 x 250 mL / Max. 12k
6 x 500 mL / Max. 9k
4 x 1,000 mL / Max. 8k
A50-8
A85-6
A250-6
A500-6
A1000-4
Supra R22 Supra R12
Cautions for Use
Inspect the rotor, chamber,
rotor & accessories for foreign objects.
Check the Chamber & Accessories
Wipe up the moisture in the chamber with
a dry cloth after use. Keep the lid open
when not in use.
Clean the chamber and rotor
by wiping with a cloth soaked in mild
detergent and dry completely.
Keep the Chamber Dry
Cleaning
Load tubes symmetrically into the rotor
with identical amount.
Load Tubes Symmetrically
Check the rotor, buckets and tubes are free
of scratch and crack before operation.
Check the Accessories for Abnormalities
After relocating the device or loading the
rotor, balance them by using a leveler. If
necessary, level the device by adjusting the
‘Leveling foot’ on the bottom of the device.
Balancing the Centrifuge and Rotor
3.4KVA (Supra R22)
3.0KVA (Supra R12)
220~240V 50/60Hz
Rev.1
Proudly made by Jiyoung Shim, Hyewon Jeong
Order & Inquiry l [phone] l [email protected] l www.ihanil.com
Service l [phone] l [email protected]
Before Operation After Operation