Episode ES-AW-360-6-BRN User manual

INSTALLATION MANUAL
OUTDOOR360°SPEAKERS
ES-AW-360-6-BRN

page | 2
Support 866.838.5052
INTRODUCTION
Thank you for purchasing Episode® speakers. To complete installation,
follow these instructions. Visit our website for design recommendations
and speaker calculators.
PACKAGE CONTENTS
• ES-AW-360-6-BRN
• Weatherproof Wire Nuts
TOOLS REQUIRED
• Coin to adjust tap switch
• Wire Stripper
SETUP
Determining Speaker Locations
• Plan locations with no more than 25’-30’ spacing between speakers.
Using more speakers in an area allows for more even sound coverage.
The final volume of the speakers can be set using the 70 volt systems
wattage tap setting. See the FINE TUNE section on page 4.
• If using a stereo sound system, place left and right speakers evenly to
avoid uneven sound.
Mounting Considerations
The speakers will not be damaged by normal rainfall, however sprinkler
systems may cause damage to the internal audio components. Avoid
placing the speakers within direct sprinkler stream areas.
CONNECT
!
CAUTION: Do not supply power to the amplifier or connect the
speaker line until all other connections have been made.
NOTE: The silicone-filled weatherized wire nuts included with this kit are
specially designed to be used for direct burial installations. An equivalent
connector must be used for any wiring in the system that could be exposed
to water or weather.
1. Attach the mount to the speaker.
2. Carefully route the speaker cable into the speaker mount, to avoid
damage to the wire insulation.

page | 3
© 2015 Episode®
3. Strip the outer jacket of the cable by at least 2" to separate it from the
insulated wires inside. Cut the wire to make a splice point if a location
has a wire loop.
4. Strip the insulation on each conductor back approximately ½".
5. Twist the wires from the run in a
clockwise direction with the speaker
wires ensuring all – (negative) wires
and all + (positive) wires are bundled
together separately.
6. Insert each set of wires into a
waterproof wire nut and twist the
nut clockwise until it is firmly seated
and completely covering the bare
copper. A small amount of silicone
may press out of the wire nut as the
wires are inserted and should be left
on the wire for the most reliable connection.
7. Set the transformer switch to the correct tap setting per the Transformer
Tap Settings section before connecting an amplifier to the system.
NOTE: Use a coin to adjust tap switch
SECURE
Speaker Mounting and Angle Adjustments
Close or secure the connections and secure the speaker via the security
ring if desired.
FINE TUNE
Transformer Tap Settings
The 360 speakers have an adjustable tap
setting switch located under the removable rear
cover. To adjust, rotate the tap setting dial on the
rear of the speaker to the desired setting.
The 360 speakers used in 70/100 volt systems
can be set to different wattages for more or
less volume at one particular speaker. This makes it much easier to fine tune
a system for even listening volume.
!
CAUTION: The speaker tap must be set accordingly for the type of
amplifier in use (8Ω or 70/100volt). Setting the transformer incorrectly
for the amplifier used could damage the speakers or amplifier.
+−
From
Amp or
Previous
Speaker
To Next
Speaker
(if not Last
Speaker)
© 2015 Episode®

Connecting the Amplifier and Testing
1. After wiring each speaker into the run and setting the taps, attach
the speaker wires to the amplifier, making sure to mirror the wiring
pattern used in the speakers, + to + and – to ‒. Connect the amplifier
to a source and to power, then test the system.
2. Listen to the system from several locations in the audible area. If an
area is too loud or quiet, adjust speaker taps or the amplifier volume
accordingly until the volume and sound quality is optimized.
3. After optimizing the settings, check the total wattage again to be sure
the amp isn’t being overworked. It is a good idea to let the system
play for about a half hour after setup is done to ensure that the
system is reliable.
4. Once the system has been set and tested, the wiring or conduit can
be buried or hidden.
TROUBLESHOOTING
Episode®speakers are designed to function trouble-free. Most problems
that occur are due to simple issues. Refer to the list of fixes below, or
contact Customer Service at 1.866.838.5052 if problems persist.
No Sound
• Verify that there is audio coming from the selected source. Slect another
source if necessary.
• Ensure the audio source is turned on and properly connected.
WARRANTY
Lifetime Warranty
Episode® speakers have a Lifetime Warranty. This warranty includes parts
and labor repairs on all components found to be defective in material or
workmanship under normal conditions of use. This warranty shall not
apply to products which have been abused, modified or disassembled.
Products to be repaired under this warranty must be returned to a
designated service and an assigned Return Authorization (RA) number.
Contact technical support for an RA number.
CONTACTING TECHNICAL SUPPORT
Episodespeakers.com
866.838.5052
[email protected]
© 2015 Episode®
Rev: 151130-1600