Episode IC-6 User manual

INSTALLATION MANUAL
ARCHITECHTURAL SPEAKERS

page | 2
snapav.com Support 866.838.5052
INTRODUCTION
Thank you for purchasing Episode® speakers. Complete the Setup,
Connect, Secure, and Fine Tune sections in this manual to ensure proper
installation. Visit our website for design recommendations and speaker
calculators.
SETUP
New Construction Install
Episode speaker installations can be simplified by using Episode
pre-construction brackets (sold separately). Install them prior to drywall
to allow for precise placement of the speaker.
Secure the wiring within reach of the bracket for easy access.
Existing Construction Install
Make a cutout for the speaker using the supplied template. Allow space
for the bezel if installing near adjacent objects, or cut the hole in two steps
as shown below.
2. If there are no obstructions, cut the
drywall again, this time at a 90° angle.
3. Insert the speaker into the cutout.
1. Cut the drywall at a 45° angle so
that if the speaker is too close to an
obstruction, you can easily ‘plug’ the
hole.
OBSTRUCTION
PLUG

page | 3
© 2015 Episode®
Cutout Dimensions
Refer to the chart below to verify the correct dimensions prior to cutting
drywall.
Model Cutout Dimension Mounting Depth
No Enclosure
Mounting Depth
with Enclosure
IC-6* 8.3” 3.6” 6.2“
IC-8 9.7” 3.7” 6.6“
*For POINT-6 models, refer to IC-8 cutout dimensions
Model Cutout Dimension Mounting Depth
No Enclosure
Mounting Depth
with Enclosure
IW-6 11.7” x 7.6” 3.6” 3.8“
IW-8 13.7” x 9.0” 3.6” 3.8“
LCR 14.4” x 7.6” 3.6” 3.8“
© 2015 Episode®

page | 4
snapav.com Support 866.838.5052
CONNECT
Strip the insulation on each conductor approximately ¼” and insert
into the speaker terminals. Ensure no strands of wire protrude from the
connectors.
Observe proper polarity for each speaker to the amplifier (+to +and –to –).
Refer to the dual voice coil speaker wiring configuration image below
when wiring a dual voice coil speaker.
Amp
Amp (Left)
Amp (Right)
Visit SnapAV.com or contact customer support for help with impedance,
system design ideas, or wiring recommendations.
SECURE
Engage and Tighten
SINGLE VOICE COIL DUAL VOICE COIL
1. Insert the speaker into the opening and
turn the screw for each of the dogs one
quarter turn clockwise to engage the spring
mechanism.
2. The speaker is now held in place, freeing
up your hands so that you may continue to
tighten the dogs safely.
ENGAGED
PARKED
Dog
Dog
Spring
Spring
Carrier

page | 5
© 2015 Episode®
Disengage and Remove
!
IMPORTANT: The dogs must be engaged AND
tightened before attempting to remove the speaker.
The dogs will not retract into the parked position if not
fully engaged and tightened.
1. Turn each dog screw in a counter-clockwise
direction until the dog is in its original parked
position.
3. Tighten to send the carrier to retrieve the
dog until you feel resistance, but do not over
tighten. If using a drill, use a low-torque setting.
2. Once the dogs are disengaged, the speaker is
easily removed from the ceiling or wall.
© 2015 Episode®
PARKED
TIGHTENED
TIGHTENED
Dog
Dog
Dog
Carrier
Carrier
Spring
Spring
Spring

page | 6
snapav.com Support 866.838.5052
Tilt
12°±
BALL & SOCKET TWEETER
Tilt
15°±
PRECISION TWEETER
ROTATE ONLY TWEETER TILT ONLY TWEETER
FINE TUNE
Adjust the Tweeter
Pull up on the perforated hole to remove the
protective installation cover.
There are four different types of tweeter
mechanisms illustrated below that may be used
depending on the type of speaker. Tilt and/or rotate
to direct sound where you prefer.
!
IMPORTANT: Do not turn any tweeter past 360°. Over-rotating may
result in tweeter damage.
12°L
12°± 15°±
12°R
+180°
+180°+180°
-180°
-180°-180°
Tilt
Rotate
Rotate Rotate
Tilt Tilt

page | 7
© 2015 Episode®
Adjust the sound
Use the switch on the face of the speaker for sound adjustment. Switches
can vary by model.
Treble/Bass Switch: Select +or ‒
NOTE: The default setting is +1.5dB.
In furnished rooms, it is recommended to set to +to increase response by
+1.5dB.
In more open spaces, it is recommended to set to ‒ to decrease response
by -1.5dB.
Bipole/Dipole Switch (Surround Only): Select BI or DI
In spacious rooms with a balanced speaker arrangement, it is
recommended to set to BI for in-phase output, which produces more
direct sound.
In rooms with varied arrangement, it is recommended to set to DI for
out-of-phase output, which produces more reverberating sound.
NOTE: Preference subject to opinion.
Dialogue Enhancement Switch (LCR Only): Select ON or OFF
Select ON for enhanced dialogue and clear speech.
D
ON
OFF
B
BASS TREBLE DIALOGUE SURROUND
© 2015 Episode®

Rev: 150727-0955
WARRANTY
Lifetime Warranty
Episode® speakers have a Lifetime Warranty. This warranty includes
parts and labor repairs on all components found to be defective in
material or workmanship under normal conditions of use. This
warranty shall not apply to products which have been abused,
modified or disassembled. Products to be repaired under this warranty
must be returned to SnapAV or a designated service center with prior
notification and an assigned Return Authorization (RA) number.
CONTACTING TECHNICAL SUPPORT
As a thank you for purchasing Episode® speakers, direct technical
support services are available via phone or e-mail. We encourage you
to use this resource for any questions or concerns about our products.
Visit our website for more support documentation.
[phone]
[e-mail]
snapav.com