EPSOM E7102 User manual

Job No …………..
E7102 –2 DRAWER BEDSIDE
Congratulations on your purchase of your EPSOM 2 DRAWER BEDSIDE. The EPSOM Collection is
made in New Zealand from 100% New Zealand made MDF –an environmentally sound renewable
resource.
If you require any parts or assembly advice or have any questions please go to
www.warehousefurniture.co.nz or call us on 0800 100 858.
WHERE TO ASSEMBLE YOUR BEDSIDE
Assemble your Bedside on a clean and smooth surface, free of anything which may damage the
laminate surface. A carpeted floor is ideal. If assembling on a workbench or table we suggest you
cover it with the carton the Bedside was packaged in.
Warning! Never leave hardware parts where children can reach them. Small parts may be a choking
hazard!
PARTS LIST
Please check you have all the parts before beginning to assembling your Bedside. The measurements
will help you identify each part. If any parts are missing or damaged please contact us directly. Do not
call the store you bought the cabinet from as they will be unable to help you. Note: You will find two
pieces of board fitted across the ends of the package. These are for packing purposes only and
are not part of the cabinet.
QTY
PART
MEASUREMENTS
NOTES
1
Top
465 x 396 x 25mm
Black laminate on one side.
1
LH End
517 x 372 x 15mm
Black laminate on both sides.
1
RH End
517 x 372 x 15mm
Black laminate on both sides.
1
Top Drawer Front
413 x 195 x 15mm
Black laminate on one side.
1
Bottom Drawer Front
413 x 235 x 15mm
Black laminate on one side.
1
Front Toeboard
419 x 80 x 15mm
Black laminate on front side only.
1
Rear Toeboard
419 x 80 x 15mm
Plain
2
LH Drawer Sides
340 x 160 x 12mm
Plain
2
RH Drawer Sides
340 x 160 x 12mm
Plain
2
Drawer Backs
369 x 155 x 12mm
Plain
2
Drawer Bottoms
379 x 339 x 4mm
Plain
1
Back Panel
462 x 439 x 4mm
Plain
EPSOM
collection

EPSOM –E7102 2
For assembly advice or parts go to www.warehousefurniture.co.nz or call 0800 100 858
HARDWARE LIST
QTY
PART
CODE
12
Connecting Bolts
H1
8
15mm Metal Cams.
H2
4
12mm Metal Cams.
H3
8
Drawer Slide Screws
H4
8
Small Woodscrews
H6
8
31mm Wood screws
H9
12
Large Dowels
H15
2
Metal drawer slides sets
H21
4
Nail on Glides
H37
1
Bag of small Nails
H27
2
Handles
H43
COLOUR CODING
To help identify the parts, the main components are colour coded with a pen mark on the back edge of
the panel. (The edge without any laminate on it.)
RED Right Hand Parts. (E.g. RH End, RH Division, RH Drawer Side.)
GREEN Left Hand Parts. (E.g. LH End, LH Division, LH Drawer Side.)
BLUE Tops
PURPLE Bases

EPSOM –E7102 3
For assembly advice or parts go to www.warehousefurniture.co.nz or call 0800 100 858
5 YEAR WARRANTY.
This furniture carries a 5 year warranty against defective material or workmanship, excluding
misuse and normal wear and tear. Obviously, as this unit is customer-assembled we cannot guarantee
cabinet failure or damage from incorrect assembly. All claims need proof of purchase –to ensure
this register @ www.warehousefurniture.co.nz.
Follow the assembly instructions carefully and take note of the precautions below.
■Avoid direct sunlight wherever possible.
■Keep cabinet in a dry place.
■Wipe off spilt liquids immediately.
■Avoid placing hot items directly on the surface.
■Clean with a soft cloth and a mild polish.
■Do not allow nail polish, removers, deodorant etc. to come into contact with the
surface.
CAM INSTALLATION & OPERATION

EPSOM –E7102 4
For assembly advice or parts go to www.warehousefurniture.co.nz or call 0800 100 858
DRAWER SLIDES
Your pack will contain two sets of Metal Drawer Slides. These are bundled together with adhesive
tape. Each set comprises of 4 components. Undo the tape on one set at a time and separate the parts.
LEFT HAND PART (DL)RIGHT HAND PART (DR)
The Drawer Slide components shown above are attached to the drawers. They have the letters DR or
DL stamped on them to indicate left hand or right hand components. Put these parts aside for
attaching to the drawers later on.
LEFT HAND PART (CL) RIGHT HAND PART (CR)
The Drawer Slide components shown above are to be attached to the cabinet. They have letters CR or
CL stamped on them to indicate left hand or right hand components.
H4 Drawer Slide Screw
Use these holes

EPSOM –E7102 5
For assembly advice or parts go to www.warehousefurniture.co.nz or call 0800 100 858
INSTALL THE HARDWARE
STEP 1
Take the LH End and lay it on a clean, clear surface with the holes facing upwards.
Take the two LH cabinet drawer slide (CL) and screw it to the LH End using the H4 Drawer Slide
Screws. Use the holes as indicated in the diagram on the previous
step.
Insert two H2 15mm Cams as indicated. Make sure the arrow on top of the cam points towards the
top edge of the End.
Push two H15 Dowels into the top edge of the End.
Screw two H1 Connecting Bolts into the holes as indicated below.
STEP 2
Repeat previous step with the right hand End. Use the CR Cabinet Drawer Slides.