Epson MF1466-01 User manual

MF1466-01
CMOS 8-BIT SINGLE CHIP MICROCOMPUTER
(Adapter Board for S1C8F360/8F361)
S5U1C8F360Z1 Manual

NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko
Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any
liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or
circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such
as medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there
is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright
infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic
products under the control of the Foreign Exchange and Foreign Trade Law of Japan and may require an export license from
the Ministry of International Trade and Industry or other approval from another government agency.
© SEIKO EPSON CORPORATION 2001 All rights reserved.

New configuration of product number
Starting April 1, 2001, the configuration of product number descriptions will be changed as listed
below. To order from April 1, 2001 please use these product numbers. For further information, please
contact Epson sales representative.
Devices
S1 C88104 F0A01
Packing specification
Package (D: die form; F: QFP)
Model number
Model name (C: microcomputer, digital products)
Product classification (S1: semiconductor)
Development tools
S5U1 C88348 D1 1
Packing specification
Version (1: Version 1)
Tool type (D1: Development Tool)
Corresponding model number (88348: for S1C88348)
Tool classification (C: microcomputer use)
Product classification
(S5U1: development tool for semiconductor products)
00
00

CONTENTS
S5U1C8F360Z1 MANUAL EPSON i
(ADAPTER BOARD FOR S1C8F360/8F361)
S5U1C8F360Z1 Manual (Adapter Board for S1C8F360/8F361)
This manual describes how to use the Adapter Board (S5U1C8F360Z1) that is a PROM writing and
evaluation tool for the 8-bit Single Chip Microcomputer S1C8F360/8F361.
Contents
CHAPTER 1INTRODUCTION ____________________________________________ 1
1.1 Outline of S1C8F360 Adapter Board (S5U1C8F360Z1) .............................1
1.2 Components of S1C8F360 Adapter Board (S5U1C8F360Z1) ..................... 1
CHAPTER 2PRECAUTIONS ____________________________________________ 2
2.1 Precautions for Operation ............................................................................ 2
2.2 Differences from the ICE88UR (S5U1C88000H5)
+ PRC88816 (S5U1C88816P) ..................................................................... 2
CHAPTER 3CONFIGURATION FOR THE S1C8F361 __________________________ 4
CHAPTER 4NAME AND FUNCTION OF EACH PART ___________________________ 5
CHAPTER 5SERIAL PROGRAMMING ______________________________________ 6
5.1 Setting the Jumpers ....................................................................................... 6
5.2 Connecting the Power Cable ........................................................................ 6
5.3 Pin Assignment of the CN4 Connector for Serial Programming .................6
CHAPTER 6CONNECTING WITH THE TARGET SYSTEM _________________________ 7
CHAPTER 7 S1C8F360 ADAPTER BOARD (S5U1C8F360Z1) SCHEMATIC DIAGRAM _9
CHAPTER 8PRODUCT SPECIFICATIONS ___________________________________ 10

CHAPTER 1: INTRODUCTION
S5U1C8F360Z1 MANUAL EPSON 1
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 1INTRODUCTION
1.1 Outline of S1C8F360 Adapter Board (S5U1C8F360Z1)
The S5U1C8F360Z1 board (hereafter Adapter Board) is a PROM writing tool for the 8-bit Single Chip
Microcomputers S1C8F360 and S1C8F361. The Adapter Board connected to the On Board Programming
Writer (S5U1C88000W3) allows writing user data to the Flash EEPROM built into the S1C8F360/8F361
(package model) placed on its IC socket using the On Board Programming Writer Control Software
(S5U1C8F360Y3).
The Adapter Board can also be used as a software evaluation board by mounting peripheral circuits on
the board.
S5U1C8F360Z1
1.2 Components of S1C8F360 Adapter Board (S5U1C8F360Z1)
After unpacking the S5U1C8F360Z1 package, check to see that all of the following components are
included.
(1) S5U1C8F360Z1 board................................................................ 1
(2) I/O cable (80-pin/40-pin ×2 flat type).................................. 2
(3) I/O cable (60-pin/30-pin ×2 flat type).................................. 1
(4) I/O connector for target system (40 pins)............................. 4
(5) I/O connector for target system (30 pins)............................. 2
(6) Power cable................................................................................. 1
(7) S5U1C8F360Z1 Manual (this manual) ................................... 1
(8) Warranty card............................................................................. 1
(9) User registration card ............................................................... 1
(10) Note for use ................................................................................ 1

CHAPTER 2: PRECAUTIONS
2EPSON S5U1C8F360Z1 MANUAL
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 2PRECAUTIONS
The connectors CN1, CN2 and CN3 have the same pin layout as the Peripheral Circuit Board for
S1C88816/8F360 (S5U1C88816P). This allows connection between the user target system for the
S5U1C88816P and the Adapter Board.
Take the following precautions when using the S1C8F360 Adapter Board (S5U1C8F360Z1):
2.1 Precautions for Operation
(1) Turn the power of all equipment off before connecting or disconnecting cables.
(2) Do not turn the power on while the input ports (K00–K03) are all set to low level. It may cause a
simultaneous key input reset.
2.2 Differences from the ICE88UR (S5U1C88000H5)
+ PRC88816 (S5U1C88816P)
The emulation system using the Adapter Board with an actual IC differs in terms of functionality and
characteristics from the S5U1C88816P emulation system, a fact which requires your attention. If these
differences are ignored, there is a possibility that your circuit will not operate properly on an actual IC
even though it might have performed well on the S5U1C88000H5 with the S5U1C88816P.
(1) Power supply differences
To operate the actual IC on the Adapter Board, an external power source voltage must be applied.
Refer to "Electrical Characteristics" chapter in the "S1C8F360 Technical Manual" for the supply
voltage.
(2) I/O differences
The output drive capability and pull up resistance are different.
The input setup time is different therefore, when a circuit requiring consideration of the input re-
sponse time, such as a key matrix, is used, the system and the software should be designed according
to the specifications for the actual IC.
(3) LCD differences
The output drive capability is different.
Since there will be differences with the actual IC even for the drive voltage, the system and the
software should be designed in order to adjust the characteristics.
(4) Analog comparator differences
The response time and characteristics of the analog comparator are different. Consequently, the
system and the software should be designed according to the specifications for the actual IC.
(5) Functional differences
<Oscillation circuit>
•The Adapter Board does not contain oscillator parts. Mount the parts according to the selected mask
option for the actual IC.
•The OSC3 oscillation stability time of the S5U1C88816P is shorter than that of the actual IC. There-
fore, the application program must take enough of interval (more than the oscillation stability time
in the actual IC) between starting the OSC3 oscillation and switching the system clock to OSC3.
•The logic level is different and it makes different oscillation timings such as the start and stop times.
•When switching the operating clock from OSC3 to OSC1, be sure to switch OSC3 oscillation off with
separate instructions. Using a single instruction to process simultaneously may cause a malfunction
of the CPU.

CHAPTER 2: PRECAUTIONS
S5U1C8F360Z1 MANUAL EPSON 3
(ADAPTER BOARD FOR S1C8F360/8F361)
•Do not turn the OSC3 oscillation circuit on in the low power mode.
Do not switch over the operating mode (normal mode ↔high speed mode) when the OSC3 oscilla-
tion circuit is on, as this will cause a malfunction.
<Internal power supply circuit>
The actual IC on the Adapter Board can change over the internal power voltage (set by VDC2, VDC1
and VDC0), but the S5U1C88816P cannot change the actual power voltage, because only the VDC2,
VDC1 and VDC0 values are changed.
For this reason, since the S5U1C88816P will operate, even if the stable time required for changeover is
not taken, be sure that the stable time is provided by the software.
Also, since the usable frequency of OSC1 and OSC3 depends on the internal power voltage, refer to
the technical manual for the S1C8F360 or S1C8F361 and take care so as not to operate it with an
inappropriate combination.
When turning the OSC3 oscillation circuit on after switching the operating voltage, the software must
take a voltage stabilization wait time of 5 msec.
<LCD drive power>
To drive an LCD using the Adapter Board, mount the parts required for VC1 to VC5 and CA to CE (CA
to CG in the S1C8F361) on the board or supply an external LCD power.
Note: The S1C8F360 Adapter Board supports the S1C8F361 as well.When using the board for the
S1C8F361, the AVDD and AVSS pins on the board must be changed to the CF and CG pins,
respectively, using the jumper and mount a capacitor to the holes indicated as C1.
<Reset circuit> ___________
Mount parts such as a switch and a capacitor at the RESET pin on the Adapter Board.

CHAPTER 3: CONFIGURATION FOR THE S1C8F361
4EPSON S5U1C8F360Z1 MANUAL
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 3CONFIGURATION FOR THE S1C8F361
The S1C8F360 Adapter Board (S5U1C8F360Z1) supports the S1C8F361 as well as the S1C8F360. In this
case, the pins listed in the table below change their functions.
Table 3.1 Pin function for S1C8F361
Print
AV
DD
AV SS
S1C8F360
AV
DD
AV SS
S1C8F361
CF
CG
When using the S1C8F361, open the AVDD and AVSS jumpers and mount the booster capacitor for the CF
and CG at C1.
CF
AVDD
AVSS
CG
C1
Fig. 3.1 CF and CG for the S1C8F361

CHAPTER 4: NAME AND FUNCTION OF EACH PART
S5U1C8F360Z1 MANUAL EPSON 5
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 4NAME AND FUNCTION OF EACH PART
This chapter describes the name and function of each part of the S1C8F360 Adapter Board
(S5U1C8F360Z1).
Fig. 4.1 Top view of the S5U1C8F360Z1 board
(1) IC socket
Insert an actual IC. Align Pin 1 with the bottom left corner of the socket (in top view) and insert IC.
(2) Connectors for target system (CN1, CN2, CN3)
These connectors are used to connect the I/O and LCD. Connect the target system using the I/O
cables (80-pin/40-pin ×2 flat type and 60-pin/30-pin ×2 flat type).
The pin assignment is the same as the S5U1C88816P connectors.
Refer to Chapter 6, "Connecting with the Target System", for the pin assignment.
(3) Connector for serial programming (CN4)
This connector is used to connect the On Board Programming Writer (S5U1C88000W3). Use this
connector when writing user data to the Flash EEPROM built into the microcomputer on the IC slot.
Refer to Chapter 5, "Serial Programming", for the pin assignment. For how to use the On Board
Programming Writer, refer to the "S1C8F360 Technical Manual".
(4) Power connector (CN5)
This connector is used to supply power to the S1C8F360 Adapter Board.
Use the supplied power cable for connection.
(5) Power system jumpers and check pins
Set according to the power supply conditions.
(6) Through holes for oscillator, LCD drive power and LCD voltage booster
Use them to mount the parts such as oscillator parts, capacitors and resistors. Refer to "Basic External
Wiring Diagram" in the "S1C8F360 Technical Manual" for the basic parts to be mounted.
(7) IC socket pattern
Cannot be used.
(5) (4)
(3)
(2)
(2)
(2)
(7)
(1)
(6)

CHAPTER 5: SERIAL PROGRAMMING
6EPSON S5U1C8F360Z1 MANUAL
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 5SERIAL PROGRAMMING
The S1C8F360 Adapter Board (S5U1C8F360Z1) connected to the On Board Programming Writer
(S5U1C88000W3) allows writing user data to the Flash EEPROM built into the S1C8F360/8F361 (package
model) placed on its IC socket using the On Board Programming Writer Control Software
(S5U1C8F360Y3).
Refer to "Appendix PROM programming" in the "S1C8F360 Technical Manual" for the programming
procedure.
5.1 Setting the Jumpers
Before performing serial programming, set the jumpers for the power unit as shown in Table 5.1.1.
Note: Be aware that the configuration is different between the S1C8F360 and the S1C8F361.
Table 5.1.1 Jumper settings for serial programming
Jumper
V
DD
V SS
AV DD
AV SS
AV REF
S1C8F360
short
short
short
short
short
S1C8F361
short
short
open
open
short
5.2 Connecting the Power Cable
Serial programming needs external power to be supplied to the CN5 connector on the S1C8F360Adapter
Board (S5U1C8F360Z1) using the supplied power cable.
Table 5.2.1 Pin assignment of the CN5 power connector
CN5
1
2
Power cable
Red
Black
Power supply
V DD
V SS
5.3 Pin Assignment of the CN4 Connector for Serial Programming
The CN4 connector is used to connect the SIO cable from the On Board Programming Writer
(S5U1C88000W3).
Table 5.3.1 Pin assignment of the CN4 connector for serial programming
CN4
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Pin name
V
D1F
V DD
CLKW
V
SS
SCLK
V
SS
TXD
V
SS
RXD
V
SS
RESET
V
SS
SPRG
V
SS
N.C.
N.C.
Function
Programming power supply pin
Power supply pin
System clock output pin
GND pin
Serial I/F clock output pin
GND pin
Serial I/F data output pin
GND pin
Serial I/F data input pin
GND pin
Initial reset output pin
GND pin
Programming mode setup output pin
GND pin

CHAPTER 6: CONNECTING WITH THE TARGET SYSTEM
S5U1C8F360Z1 MANUAL EPSON 7
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 6C ONNECTING WITH THE T ARGET S YSTEM
The Adapter Board (S5U1C8F360Z1) can be used as an evaluation board by connecting it with the user
target board.
(1) To operate the microcomputer on the Adapter Board, the user must provide the peripheral circuits.
Refer to "Basic External Wiring Diagram" in the "S1C8F360 Technical Manual" for the required circuits.
(2) Use the supplied I/O cables (80-pin/40-pin ×2 flat type and 60-pin/30-pin ×2 flat type) for connect-
ing between the S1C8F360 Adapter Board (S5U1C8F360Z1) and the target system.
(3) Be sure to turn the power off before connecting the target system because the I/O cable includes a
power line (VDD).
CN1-1
(40 pins)
CN1-2
(40 pins)
I/O cables
To target board
CN2-1
(40 pins)
CN2-2
(40 pins)
CN3-1
(30 pins)
CN3
CN2
CN1
CN3-2
(30 pins)
mark
Fig. 6.1 Connecting with the target system

CHAPTER 6: CONNECTING WITH THE TARGET SYSTEM
8EPSON S5U1C8F360Z1 MANUAL
(ADAPTER BOARD FOR S1C8F360/8F361)
Table 6.1 Pin assignment of the I/O connectors
40-pin CN1-1
CN1
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Pin name
VDD
VDD
VSS
VSS
K00
K01
K02
K03
K04
K05
K06
K07
K10
K11
P00
P01
P02
P03
P04
P05
P06
P07
P10
P11
P12
P13
P14
P15
P16
P17
R00
R01
R02
R03
R04
R05
R06
R07
R10
R11
40-pin CN1-2
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Pin name
R12
R13
R14
R15
R16
R17
R20
R21
R22
R23
R24
R25
R26
R27
R30
R31
R32
R33
R34
R35
R36
R37
R50
R51
COM0
COM1
COM2
COM3
COM4
COM5
COM6
COM7
COM8
COM9
COM10
COM11
COM12
COM13
COM14
COM15
40-pin CN2-1
CN2
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Pin name
VDD
VDD
VSS
VSS
RESET
MCU/MPU
OSC1
OSC3
VC1
VC2
VC3
VC4
VC5
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
40-pin CN2-2
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
Pin name
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
SEG41
SEG42
SEG43
SEG44
SEG45
SEG46
SEG47
SEG48
SEG49
SEG50
COM31
COM30
COM29
COM28
COM27
COM26
COM25
COM24
COM23
COM22
COM21
COM20
COM19
COM18
COM17
COM16
30-pin CN3-1
CN3
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Pin name
SEG51
SEG52
SEG53
SEG54
SEG55
SEG56
SEG57
SEG58
SEG59
SEG60
SEG61
SEG62
SEG63
SEG64
SEG65
SEG66
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
30-pin CN3-2
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Pin name
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.

CHAPTER 7: S1C8F360 ADAPTER BOARD (S5U1C8F360Z1) SCHEMATIC DIAGRAM
S5U1C8F360Z1 MANUAL EPSON 9
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 7 S1C8F360 ADAPTER BOARD
(S5U1C8F360Z1) SCHEMATIC DIAGRAM
1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
D D C C B B A A
CA CA
CB CC
CDCE
SEG1 COM6 COM0 R34
R10
R04
VDD
VDD XSPRG COM27
SEG31
SEG28
SEG26
SEG25
R25 R16
AVREF
P14
SEG14
SEG11
COM8 COM7
R03
P03
COM18 COM28
SEG10
SEG4
R37 R31 R23 R14
AVDD/CF
K00
COM19
SEG42
SEG12
SEG2
COM14
R01
P05
P16
K03
COM17 COM20
SEG39
COM10 COM9 VSS R32
K05
K07
COM21 COM29
SEG37
SEG34
SEG29
SEG27
R21 R12
P11
K11
XRESET
COM22 COM30
SEG32
SEG30
SEG19
SEG9
SEG8
SEG0 COM12 COM11
R07
R06
P00
P07
COM23
SEG18
SEG6
R51 R30 R17
P13
COM31
SEG5
COM13
P02
P17
COM24
SEG44
SEG41
SEG3
COM1 R36 R35 R24
K02
SEG47 SEG46
SEG36
R15
R02
AVSS/CG
P15
K01
K04
SEG50
SEG33
SEG24
SEG22
SEG21
COM3 COM2 R26
P04
K06
K10
VD1 COM25
SEG23
SEG17
SEG16
SEG7
MCU/MPU
R27 R22 R13
R05
P10
XTEST
VD1F SEG49
COM15 COM4 R11
R00
P06
OSC1
RXD COM26
SEG13
COM5 R50 R33 R20
VEPEXT COM16 SEG48
SEG43
SEG40
SEG15
P01
P12
SCLK CLKW
SEG38
SEG35
SEG20
VSS VOSC OSC3 VC2 VC3
VC2 VC4
VC3 VC5 VC5 VC4 CD
CA
CB CB CC CC
OSC2OSC2
CE CD
TXD CE
GND
GND
VOSC
VD1
VC1 CA
OSC3 VC1 VEPEXT
OSC4 OSC4
VD1F
VDD
VSS
VSS
AVREF
AVDD/CF
AVSS/CG
VDD
OSC1
COM21 COM24COM7
COM8 R16
SEG13 SEG25
SEG34 SEG33 COM20
SEG59P04
P16 K04 VDD
COM2 R25
COM31 SEG66
P22 P23
COM4 R22
SEG21 OSC1
COM27 SEG35 SEG30 SEG36 COM16
P12 K00 K03
R35 R36 R12
SEG4 MCU/MPU SEG2
VDD
R50 R26
SEG1 SEG11
SEG47
SEG54
P15
R30 R21
SEG14 SEG20 SEG8
SEG41 SEG49
SEG51
P00
R15
SEG22
SEG37
P02
COM6
COM23
P27 COM17 K05
COM15
SEG44 COM18COM13
SEG57
P25 P17 P24 VSS
SEG5
COM19 SEG29 SEG45
K06
R27
SEG6 VSS
P14
SEG7
SEG39 SEG31
VDD SEG15
P20
COM1
COM28 SEG38
K10
R17
VC4 SEG16 VC2 VC3
COM29 COM22
SEG60 SEG53
P07
SEG58
R37
SEG18
SEG40 SEG55
SEG52
K11
SEG19
COM10
XRESET
P03
COM11 R20
P10
COM9 R31 R32
SEG32
SEG62
K01
SEG0
R10
VDD
COM26
P01
SEG61
P26
SEG42
COM0
SEG56
VSS
OSC3
SEG50
P21 K02
SEG23
P11
COM25
SEG12
COM14 R33 SEG43
SEG27
R13
VC5 VC1
SEG48
R14
SEG63
P06 R11 SEG26
VSS
K07
SEG46
R51
P05
SEG9 SEG64 SEG17
R23
SEG28
P13 COM30 SEG65
COM12 R24
SEG24
COM3 COM5 R34
SEG3 SEG10
XRESET GND VDD VD1F TXD RXD XSPRG GND GND SCLK GND GND CLKW GND
VCC
VCC
VCC
VCC GND
XRESET
XSPRG
XTEST
K00
K01
K02
K03
K04
K05
K06
K07
K10
K11
MCU/MPU
U1 S1C8F360
SEG2 1
SEG3 2
SEG4 3
SEG5 4
SEG6 5
SEG7 6
SEG8 7
SEG9 8
SEG10 9
SEG11 10
SEG12 11
SEG13 12
SEG14 13
SEG15 14
SEG16 15
SEG17 16
SEG18 17
SEG19 18
SEG20 19
SEG21 20
SEG22 21
SEG23 22
SEG24 23
SEG25 24
SEG26 25
SEG27 26
SEG28 27
SEG29 28
SEG30 29
SEG31 30
SEG32 31
SEG33 32
SEG34 33
SEG35 34
SEG36 35
SEG37 36
SEG38 37
SEG39 38
SEG40 39
SEG41 40
SEG42 41
SEG43 42
SEG44 43
SEG45 44
SEG46 45 SEG47 46 SEG48 47 SEG49 48 SEG50 49
COM32 50 COM30 51 COM29 52 COM28 53 COM27 54 COM26 55 COM25 56 COM24 57 COM23 58 COM22 59 COM21 60 COM20 61 COM19 62 COM18 63 COM17 64 COM16 65
VD1F 66
XSPRG 67
CLKW 68
VEPEXT 69
RXD 70
SCLK 71
TXD 72
CE 73
CD 74 CC 75
CB 76 CA 77
VC5 78 VC4 79 VC3 80 VC2 81 VC1 82
OSC3 83 OSC4 84
VD1 85
VDD 86
VSS 87
VOSC 88
OSC1
89
OSC2
90
/TEST
91
/RESET
92
K11
94
K10
95
K07
96
K06
97
K05
98
K04
99
K03
100
K02
101
K01
102
K00
103
P17
104
P16
105
P15
106
P14
107
P13
108
P12
109
P11
110
P10
111
AVDD
112
AVSS
113
AVREF
114
VDD
115
P07
116
P06
117
P05
118
P04
119
P03
120
P02
121
P01
122
P00
123
R00
124
R01
125
R02
126
R03
127
R04
128
R05
129
R06
130
R07
131
R10
132
R11
133
R12
134
R13
135
R14
136
R15
137
R16
138
R17
139
R20
140
R21
141
R22
142
R23
143
R24
144
R25
145
R26
146
R27
147
R30
148
R31
149
R32
150
R33
151
R34
152
R35
153
R36
154
R37
155
VSS
156
R50
157
R51
158
COM0
159
COM1
160
COM2
161
COM3
162
COM4
163
COM5
164
COM6
165
COM7
166
COM8
167
COM9
168
COM10
169
COM11
170
COM12
171
COM13
172
COM14
173
COM15
174
SEG0
175
SEG1
176
MCU/MPU
93
Cp
Rf
CD2 CG2
R1
VC5 VC1 VC3 VC4 VC2
XTAL1
XTAL2
CG1
JP1
VDD
JP2
VSS
JP3
AVDD/CF AVSS/CG
JP4 JP5
AVREF VOSC VD1 VD1F
VOSC VD1
VEPEXT
CN1
1-1
1
1-2
2
1-3
3
1-4
4
1-5
5
1-6
6
1-7
7
1-8
8
1-9
9
1-10
10
1-11
11
1-12
12
1-13
13
1-14
14
1-15
15
1-16
16
1-17
17
1-18
18
1-19
19
1-20
20
1-21
21
1-22
22
1-23
23
1-24
24
1-25
25
1-26
26
1-27
27
1-28
28
1-29
29
1-30
30
1-31
31
1-32
32
1-33
33
1-34
34
1-35
35
1-36
36
1-37
37
1-38
38
1-39
39
1-40
40
2-1 41 2-2 42 2-3 43 2-4 44 2-5 45 2-6 46 2-7 47 2-8 48 2-9 49
2-10 50 2-11 51 2-12 52 2-13 53 2-14 54 2-15 55 2-16 56 2-17 57 2-18 58 2-19 59 2-20 60 2-21 61 2-22 62 2-23 63 2-24 64 2-25 65 2-26 66 2-27 67 2-28 68 2-29 69 2-30 70 2-31 71 2-32 72 2-33 73 2-34 74 2-35 75 2-36 76 2-37 77 2-38 78 2-39 79 2-40 80
CN3
1-1
1
1-2
2
1-3
3
1-4
4
1-5
5
1-6
6
1-7
7
1-8
8
1-9
9
1-10
10
1-11
11
1-12
12
1-13
13
1-14
14
1-15
15
1-16
16
1-17
17
1-18
18
1-19
19
1-20
20
1-21
21
1-22
22
1-23
23
1-24
24
1-25
25
1-26
26
1-27
27
1-28
28
1-29
29
1-30
30
2-1 31 2-2 32 2-3 33 2-4 34 2-5 35 2-6 36 2-7 37 2-8 38 2-9 39
2-10 40 2-11 41 2-12 42 2-13 43 2-14 44 2-15 45 2-16 46 2-17 47 2-18 48 2-19 49 2-20 50 2-21 51 2-22 52 2-23 53 2-24 54 2-25 55 2-26 56 2-27 57 2-28 58 2-29 59 2-30 60
CN2
1-1
1
1-2
2
1-3
3
1-4
4
1-5
5
1-6
6
1-7
7
1-8
8
1-9
9
1-10
10
1-11
11
1-12
12
1-13
13
1-14
14
1-15
15
1-16
16
1-17
17
1-18
18
1-19
19
1-20
20
1-21
21
1-22
22
1-23
23
1-24
24
1-25
25
1-26
26
1-27
27
1-28
28
1-29
29
1-30
30
1-31
31
1-32
32
1-33
33
1-34
34
1-35
35
1-36
36
1-37
37
1-38
38
1-39
39
1-40
40
2-1 41 2-2 42 2-3 43 2-4 44 2-5 45 2-6 46 2-7 47 2-8 48 2-9 49
2-10 50 2-11 51 2-12 52 2-13 53 2-14 54 2-15 55 2-16 56 2-17 57 2-18 58 2-19 59 2-20 60 2-21 61 2-22 62 2-23 63 2-24 64 2-25 65 2-26 66 2-27 67 2-28 68 2-29 69 2-30 70 2-31 71 2-32 72 2-33 73 2-34 74 2-35 75 2-36 76 2-37 77 2-38 78 2-39 79 2-40 80
CN4
1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16
CN5
1 2
1 2
C1
XRESET
XSPRG
XTESTK00K01K02K03K04K05K06K07K10K11
MCU/MPU

CHAPTER 8: PRODUCT SPECIFICATIONS
10 EPSON S5U1C8F360Z1 MANUAL
(ADAPTER BOARD FOR S1C8F360/8F361)
CHAPTER 8PRODUCT SPECIFICATIONS
The component specifications of the S1C8F360 Adapter Board (S5U1C8F360Z1) are listed below.
S5U1C8F360Z1
Dimensions:
183 mm (L) ×154 mm (W) ×48 mm (H)
Power supply:
Within the operating voltage range of the microcomputer
I/O cable (80-pin/40-pin ×2, 2 sets)
S5U1C8F360Z1 connector:
KEL 8830-80-170L or equivalent
Cable connector (80-pin):
KEL 8822E-080-171 ×1/1 set
Cable connector (40-pin):
3M 7940-6500SC ×2/1 set
Cable: 40-pin flat cable ×2/1 set
Length:
Approx. 40 cm (both cables are the same length)
I/O connection cable (60-pin/30-pin ×2, 1 set)
S5U1C8F360Z1 connector:
KEL 8830-60-170
Cable connector (60-pin):
KEL 8822E-060-171 ×1/1 set
Cable connector (30-pin):
3M 7930-6500SC ×2/1 set
Cable: 30-pin flat cable ×2/1 set
Length:
Approx. 40 cm
Power cable
S5U1C8F360Z1 connector:
J.S.T. Mfg Co., Ltd B2B-XH-A
Cable connector:
J.S.T. Mfg Co., Ltd XHP-2
Contacts:
J.S.T. Mfg Co., Ltd SXH-001T-P0.6
Length:
Approx. 35 cm
Accessories
I/O connectors for the target system
(40-pin): 3M 3432-6002LCSC ×4
(30-pin): 3M 3440-6002LCSC ×2

AMERICA
EPSON ELECTRONICS AMERICA, INC.
- HEADQUARTERS -
150 River Oaks Parkway
San Jose, CA 95134, U.S.A.
Phone: [phone] Fax: [phone]
- SALES OFFICES -
West
1960 E. Grand Avenue
EI Segundo, CA 90245, U.S.A.
Phone: [phone] Fax: [phone]
Central
101 Virginia Street, Suite 290
Crystal Lake, IL 60014, U.S.A.
Phone: [phone] Fax: [phone]
Northeast
301 Edgewater Place, Suite 120
Wakefield, MA 01880, U.S.A.
Phone: [phone] Fax: [phone]
Southeast
3010 Royal Blvd. South, Suite 170
Alpharetta, GA 30005, U.S.A.
Phone: +1-877-EEA-0020 Fax: [phone]
EUROPE
EPSON EUROPE ELECTRONICS GmbH
- HEADQUARTERS -
Riesstrasse 15
80992 Munich, GERMANY
Phone: [phone] Fax: [phone]
SALES OFFICE
Altstadtstrasse 176
51379 Leverkusen, GERMANY
Phone: [phone] Fax: [phone]
UK BRANCH OFFICE
Unit 2.4, Doncastle House, Doncastle Road
Bracknell, Berkshire RG12 8PE, ENGLAND
Phone: [phone] Fax: [phone]
FRENCH BRANCH OFFICE
1 Avenue de l' Atlantique, LP 915 Les Conquerants
Z.A. de Courtaboeuf 2, F-91976 Les Ulis Cedex, FRANCE
Phone: [phone] Fax: [phone]
BARCELONA BRANCH OFFICE
Barcelona Design Center
Edificio Testa, Avda. Alcalde Barrils num. 64-68
E-08190 Sant Cugat del Vallès, SPAIN
Phone: [phone] Fax: [phone]
ASIA
EPSON (CHINA) CO., LTD.
23F, Beijing Silver Tower 2# North RD DongSanHuan
ChaoYang District, Beijing, CHINA
Phone: [phone] Fax: [phone]
SHANGHAI BRANCH
4F, Bldg., 27, No. 69, Gui Jing Road
Caohejing, Shanghai, CHINA
Phone: [phone] Fax: [phone]
EPSON HONG KONG LTD.
20/F., Harbour Centre, 25 Harbour Road
Wanchai, Hong Kong
Phone: [phone] Fax: [phone]
Telex: 65542 EPSCO HX
EPSON TAIWAN TECHNOLOGY & TRADING LTD.
10F, No. 287, Nanking East Road, Sec. 3
Taipei
Phone: [phone] Fax: [phone]
Telex: 24444 EPSONTB
HSINCHU OFFICE
13F-3, No. 295, Kuang-Fu Road, Sec. 2
HsinChu 300
Phone: [phone] Fax: [phone]
EPSON SINGAPORE PTE., LTD.
No. 1 Temasek Avenue, #36-00
Millenia Tower, SINGAPORE 039192
Phone: [phone] Fax: [phone]
SEIKO EPSON CORPORATION KOREA OFFICE
50F, KLI 63 Bldg., 60 Yoido-dong
Youngdeungpo-Ku, Seoul, 150-763, KOREA
Phone: [phone] Fax: [phone]
SEIKO EPSON CORPORATION
ELECTRONIC DEVICES MARKETING DIVISION
Electronic Device Marketing Department
IC Marketing & Engineering Group
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] Fax: [phone]
ED International Marketing Department Europe & U.S.A.
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] Fax: [phone]
ED International Marketing Department Asia
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] Fax: [phone]
International Sales Operations

In pursuit of “Saving”Technology, Epson electronic devices.
Our lineup of semiconductors, liquid crystal displays and quartz devices
assists in creating the products of our customers’ dreams.
Epson IS energy savings.

http://www.epson.co.jp/device/
(Adapter Board for S1C8F360/8F361)
S5U1C8F360Z1 Manual
EPSON Electronic Devices Website
ELECTRONIC DEVICES MARKETING DIVISION
Issue July, 2001
Printed in Japan A
L