Epson Stylus C80WN User manual

1Take everything out of the box.
2Remove all the tape and packing material from the printer, as shown.
3Insert the paper support.
4Plug in the printer and turn it on. The green power light flashes.
5Lower the output tray and open the cover.
6Shake each ink cartridge, then unwrap it.
7Insert each cartridge into its holder until the cartridge clicks
into place.
8Press the ink button and close the printer cover.
Wait while the ink charges.
9Load paper and pull out the output tray extensions.
To check the printer, first turn it off. Then hold down the
paper button as you press and release the power button to
turn it back on. The test page prints.
If the test page doesn’t print, see the Problem Solving
chapter in Printer Basics.
2Connect the Print Server
1Slide the print server into the base and press firmly.
2Turn off the printer. Then connect the parallel cable
to the printer and print server.
3Connect the power supply to the print server and
plug in the AC adapter. Both the green and yellow
lights come on and then go out.
4Turn on the printer.
5To test the connection, press the test
button for one second and release it.
The status page prints.
If the status page doesn’t print,
see page 41 in Setup and Installation.
Quick Start
1Unpack and Set Up the Printer
EPSON Stylus®C80WN
Quick Start
Turn over
Make sure you follow all the
Safety Instructions in Printer Basics
and Setup and Installation.
Keep ink cartridges out of the reach of children.
If ink gets on your skin, wash the area thoroughly
with soap and water. If ink gets in your eyes, flush
them immediately with water.
Don’t remove the cartridge labels, or ink may leak.
3Install the Software
1Make sure the wireless mode for your computer
is set to Infrastructure and WEP encryption is disabled.
For instructions, see the documentation for your
wireless adapter.
2Note your computer’s IP address. You can view the
address by running ipconfig (Windows XP/2000/NT)
or winipcfg (Windows Me/98/95). If you need
instructions, see page 52 in Setup and Installation.
3Insert your printer CD-ROM.
4Double-click Install EPSON Stylus C80WN Printer
Driver and follow the instructions on the screen.
5When you see this window, click Stop searching.
Then follow the instructions on the screen
to register your printer.
6Double-click Install C80WN Utilities on the
EPSON Installation Program screen.
7If you see a message about installing the Java
Runtime Environment click Continue and
follow the instructions on the screen.
8When you see this window, click Next.
Then follow the instructions on the back
of this sheet.
Follow these instructions if you’re an advanced Windows user and your network has a wireless access
point without WEP encryption. This includes wired networks that have wireless access points. For
more detailed instructions and other types of networks (including Macintosh®) see your Setup and
Installation book.
test button
paper support
printer
ink cartridges
print server
power supply printer power cord
parallel cable
print server base
print server Printer Basics
printer software
CD-ROM
Setup and
Installation

1Do one of the following:
In Windows XP: click Start > Control Panel >
Printers and Other Hardware > Printers and Faxes.
In Windows 2000: click Start > Settings > Printers.
2Right-click your printer icon, then click Properties.
3On the Ports tab, select your printer (if necessary),
and click Add Port.
4Select Standard TCP/IP Port and click New Port.
5When you see the Add Standard TCP/IP
Printer Port Wizard, click Next.
6Enter your print server’s IP address or server name
and click Next.
7Follow the instructions on the screen to complete
the wizard.
8Click Close to close the Printer Ports window,
then click Apply on the Properties window.
9To test the connection, select the General tab and click Print Test Page.
If the test page prints, click OK to close the Properties window.
If it doesn’t print, try the solutions on page 30 in Setup and Installation.
After the files are installed, you see the Wireless Server
Search window:
1Click START. You see server information
like this:
It may take up to 2 minutes for the
server information to appear.
If WP-Admin doesn’t pick up a signal from
the print server, check the solutions beginning
on page 41 in Setup and Installation.
2When you see server information on the screen,
click STOP. Then click CONFIGURE.
3When you see a message asking for
a password, click OK. You see the
Wireless Server Configuration screen.
4For Boot Method, select STATIC.
5Enter an IP address that conforms to the
IP addressing scheme for your network.
For example, if you have two computers
on your network whose IP addresses are
192.189.207.3 and 192.189.207.4, the print
server’s IP address should begin with
192.189.207. The last part of the address
can be any number between 2 and 254
except 3 or 4.
If your network supports DHCP, change
only the last segment of the IP address,
and make sure it is out of the range of
DHCP assignments.
For example, if the last segment of assigned
addresses is between 100 and 200, choose
a number below 100 or above 200. Make
sure you don’t use the same IP address as
another node on your network.
6Make any other changes you want and
click OK. When you see the Wireless
Server Search window again, click QUIT.
7When you see this screen, click Finish.
8If you’re running Windows Me, 98, or 95,
double-click Install EpsonNet Direct Print
Utility on the EPSON Installation Program
screen. Follow the on-screen instructions to
install the utility and restart your computer.
9Continue with the instructions in the
next section.
EPSON and EPSON Stylus are registered trademarks of SEIKO EPSON CORPORATION.
General Notice: Other product names used herein are for identification purposes only and
may be trademarks of their respective owners. EPSON disclaims any and all rights in those marks.
Copyright © 2002 by Epson America, Inc. Printed on recycled paper. 3/02
Printed in USA
CPD-13805
5Set Up a Network Port
4Configure the Print Server
For descriptions of all the settings
on the Wireless Server Configuration
screen, see Appendix A in Setup
and Installation.
Before you begin, run WP-Admin and note the IP address of your print server. Then follow the
instructions in one of the sections below, depending on which version of Windows you’re using.
Windows XP or 2000
1Click Start > Settings > Printers.
2Right-click your printer icon, then click Properties.
Click the Details tab.
3Click Add Port.
4Make sure Network is selected, then click Browse.
5Click to expand the network path, then click
the + next to Epson-Ipr and select your printer.
6Click OK, then click OK again. Click Apply
on the Details tab.
7To test the connection, click the General tab
and click Print Test Page.
If the test page prints, click Yes, then
click OK to close the Properties window.
If it doesn’t print, try the suggestions
on page 33 in Setup and Installation.
Congratulations! You’re ready for wireless printing.
See Printer Basics for more information.
Windows Me, 98, or 95
Before you set up the port, you need to install the
EpsonNet Direct Print Utility (if you haven’t already
done so). Double-click Install EpsonNet Direct Print
Utility on the EPSON Installation Program screen,
then follow the on-screen instructions to install
the utility and restart your computer.
For Mac OS X sypport,
go to the EPSON web site
at support.epson.com.