Epson TM-P60II User manual

One Blue Hill Plaza, 16th Floor, PO Box 1546
Pearl River, NY 10965
1-800-PC-AMERICA, 1-800-722-6374
(Voice) 845-920-0800 (Fax) 845-920-0880
1 | P a g e
EPSON TM-P60II Receipt Printer
Installation for Windows 7 (32/64BIT)

2 | P a g e
Table of Contents
TM-P60 Wireless Thermal Printer Information/Requirements
Setting Up the Wireless Printer
Resetting the Printer to Factory Default
Installing the Epson Ethernet Configuration Utility
Configuring the TM-P60 using the EpsonNet Config utility
Installing the Epson Printer Driver
Configuration in CRE/RPE

3 | P a g e
TM-P60II Wireless Thermal Printer Information/Requirements
Requirements:
1. An available wireless network:
This network must be setup and configured prior to any configuration from pcAmerica.
The following network types are supported with the use of the TM-P60II Thermal
Receipt Printer:
oWPA Encryption (TKIP)
2. Information on the wireless network which you will be connecting the printer to:
SSID (or network name)
Wireless Password
Subnet mask of the network
IP Address of the router (Default Gateway)
3. A laptop or PC for configuration of the device.

4 | P a g e
Setting Up the Wireless Printer
1. On the right side of the printer we will need to
locate the battery door.
2. Press the lever and open the door.
3. Insert the battery into the compartment.

5 | P a g e
4. Plug the power cable into the power brick and the
other end of the power cable into a power source
(wall outlet).

6 | P a g e
5. Plug the other end of the cable into the port on
the left side of the printer.

7 | P a g e
6. Loosen the cover (trident symbol) of the mini USB
port located on the top left of the printer.
7. Locate the Mini USB to USB-A cable.

8 | P a g e
8. Attach the Mini USB connector to the
corresponding port on the receipt printer.
9. Attach the USB-A connector (other end of the
cable) to an available USB port on your computer.
Note: The USB connection is used to configure the
TM-P60II wireless connection. The TM-P60II can
only be used with CRE/RPE through your WiFi
network.

9 | P a g e
Resetting the Printer to Factory Default
Before doing any configuration on the device we must first reset it back to factory defaults.
1. Press the button on the top right of the printer, to
release the paper roll cover.
2. Press and hold the FEED button and press the
POWER button, to power on the printer.
3. When the printer has powered on, press the FEED
button 6 times, then close the paper roll cover.
Note: When closing the paper cover, make sure the
paper is in between the guides so that it can be ejected
properly.

10 | P a g e
4. The SELF-TEST page will then be printed.
5. To initialize the printer, open the paper roll cover,
press the FEED button 1 time, then close the paper
roll cover.
6. Initialize will then print on the receipt paper and the
paper roll will then be cut. This will start the factory
reset process.
7. The printer will restart after initialization has
completed.

11 | P a g e
Installing the Epson Ethernet Configuration Utility
Download the Epson Ethernet configuration utility from the following link:
http://download2.pcamerica.com/drivers/EpsonNetConfig_v443.zip
1. Extract the downloaded zip file. Right click or hold
down the extracted file EpsonNetConfig_v433.exe
and select Run as administrator. (If you are using
Windows XP, simply double click on the file.)
Note: depending on your Windows settings, the .exe
extension may not be visible
2. Follow the installation steps which will install the
EpsonNet Config V4. Select English, then Next.
3. Select Next.

12 | P a g e
4. Select I accept the terms of the license agreement.
5. Select Next.
6. Select Next.

13 | P a g e
7. Select Install.
8. Select Finish.

14 | P a g e
Configuring the Epson TM-P60 II using the EpsonNet Config utility
NOTE: Only one printer should be configured at a time, as all printers have the same settings
configured from the factory (i.e. default IP 192.168.192.168).
Power on the printer and connect cable to the computer via (mini USB to USB-A Cable).
1. Select Start, point to All Programs, point EpsonNet; then
select EpsonNet Config.
2. Select the printer that you want to set the IP address for
(its default IP when reset is 192.168.192.168), and then
select the Configuration button.

15 | P a g e
3. Select Basic under the TCP/IP tab.
4. Select Manual for Method for Specifying IP Address.
5. Assign the IP address, the Subnet mask, and the Default
gateway (this information can be obtained by typing
ipconfig in a Windows command prompt):
IP Address - Enter an IP Address that is in the scope
of your routers DHCP settings, in our example we
will use 192.168.1.104. DO NOT use the same IP
Address of any other PCs or devices on the network.
Subnet Mask - Enter the Subnet Mask for the
network. (Usually it is 255.255.255.0)
Default Gateway - Enter the IP Address of the router
or DHCP server. (Usually this can be left blank)
If you are not sure, ask your network administrator for the IP
address, Subnet Mask and the Default gateway to be set.
6. Select OK.
7. Select Basic (Wireless) under the Network tab.
8. Select Infrastructure for the Communication Mode.
9. For SSID, enter the SSID for your wireless network (in
our example we connected to a network called
PCAMobile).
10. Under Security Level select the network security type as
WPA-PSK (TKIP).
11. For PSK (Pre-shared Key): Enter the password you use to
access your wireless network. Re-enter your password in
the box beneath.
12. Select Transmit.

16 | P a g e
13. Select OK.
14. Select OK.

17 | P a g e
Installing the Epson Printer Driver
The printer driver for the device can be downloaded from:
http://download2.pcamerica.com/drivers/APD_455dE.zip
1. Extract the downloaded file. Locate and right click on the
file named APD_455dE and select Run as administrator.
2. Select Next.
3. Select I accept the terms of the license agreement.
4. Select Next.

18 | P a g e
5. Select Standard.
6. Select Next.
7. Select Add.

19 | P a g e
8. Use the dropdown next to Select Driver to select the
EPSON TM-P60II Receipt.
9. Optionally enter a Printer name.
10. Use the dropdown next to Port Type to select Create an
Ethernet port.
11. Optionally select Set as Default Printer.
12. Select Next.
13. Enter the IP Address that was setup for the printer in our
example we used 192.168.1.104.
14. Select Next.

20 | P a g e
15. Select Next.
16. Select Next.