Epson EB-585Wi User manual

Installation Guide

Using the Product Safely
1
Safety Instructions
For your safety, read all the instructionsin this guide before using this product. Incorrect handling that ignores
instructions in this guide could damage this product or could result in personal injury or property damage.
Keep this installation guide at hand for future reference.
Read the User'sGuide and SafetyInstructions for your projector and follow the instructions in these documents.
Safety indications
The documentation and this product use graphical symbols to show how to use this product safely.
The indications and their meaning are as follows. Make sure you understand them properly before reading
the guide.
Symbol Explanation
Warning This symbol indicates information that, if ignored, could possibly result in personal injury or
even death due to incorrect handling.
Caution This symbol indicates information that, if ignored, could possibly result in personal injury or
physical damage due to incorrect handling.
Explanation of Symbols
Symbols Explanation
Symbol indicating an action that must not be done
Symbol indicating an action that should be done
c
Symbol indicating related or useful information
Safety Precautions for Installation
Warning
The setting plate is exclusively for mounting the projector on a wall. If anything other than
a projector is mounted, the weight may result in damage.
If this product falls, it could cause death or personal injury.
The installation work (wall mounting) should be performed by specialists who have tech‐
nical knowledge and ability. Incomplete or incorrect installation could cause the product
to fall and cause personal injury or property damage.
Follow the instructions in this guide when installing this product.
If the instructions are not followed, this product may fall, resulting in personal injury or an accident.

Using the Product Safely
2
Warning
Handle the power cord carefully.
Incorrect handling may cause fire or electric shock. Observe the following precautions when han‐
dling:
•
Do not handle the power plug with wet hands.
•
Do not use a power cord that is damaged or modified.
•
Do not pull the power cord with too much force when routing the cable through the setting plate.
Do not install the setting plate in a place where it might be subjected to vibration or shock.
This could cause damage to the projector or mounting surface. If this product falls, it could cause
death or personal injury.
Install the setting plate so that it can sufficiently support the mass of the projector and
setting plate, and resist any horizontal vibration. Use M10 nuts and bolts.
Nuts and bolts smaller than M10 could cause the setting plate to fall. Epson accepts noresponsibility
for any damage or injury caused by lack of wall strength or inadequate installation.
The installation work should be performed by at least two qualified service personnel. If
you need to loosen any screws during installation, be careful not to drop this product.
If this product falls, it could cause death or personal injury.
When mounting this product on a wall, the wall requires enough strength to hold the
projector and the setting plate.
This product should be installed on a concrete wall. The maximum combined weight of the pro‐
jector and the setting plate is approximately 14 kg (not including cables). Ensure the strength of
the wall before mounting this product on the wall. If the wall is not strong enough, reinforce the
wall before installation.
Inspect the setting plate on a regular basis to ensure there are no broken parts or loose
screws.
If any parts are damaged, stop using the setting plate immediately. If this product falls, it could
cause death or personal injury.
Do not disassemble or remodel this product.
There are numerous high-voltage sections inside the product that could cause a fire, electric shock,
or an accident.
Do not hang on this product or hang a heavy object on this product.
If this product falls, it could cause death or personal injury.
Do not use adhesives, lubricants, or oils to install or adjust the setting plate.
If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on
the slide plate fixing part of the projector, the case may crack and cause the projector to fall,
resulting in personal injury or property damage.
Tighten all screws firmly after adjustment.
Otherwise, the product may fall and cause personal injury or property damage.
Never loosen the bolts and nuts after installation.
Confirm that the screws have not become loose on a regular basis. If you find any loose screws,
tighten them firmly. Otherwise, the product may falland cause personal injury or property damage.
Route the cables so that they do not interfere with the nuts and bolts.
Incorrect handling of the cables may cause fire or electric shock.

Using the Product Safely
3
Warning
When turning on the projector, do not look into the projection window.
This could cause damage to eyesight due to the powerful light emitted. Take particular care when
there are children present. When turning on the projector at a distance using the remote control,
make sure there is no one looking into the projection window.
When using the projector, do not place any objects or put your hand near the projection
window.
This area is dangerous as it reaches a high temperatures due to the concentrated projection light.
Do not cover the projector's air intake vent or air exhaust vent. If either of the vents are
covered, the internal temperature could rise and cause a fire.
Avoid locations subject to high temperatures, such as close to heaters, and leave a gap of at least
20 cm between the wall and the air exhaust vent.
Do not use the projector in a location subject to combustible or explosive gas.
The projector may catch fire because of the high temperature of the lamp inside the projector.
If any abnormalities occur with this product, immediately disconnect the cables from the
product, and then contact your local dealer or the nearest Epson service call center.
Continuing to use the product in an abnormal condition could cause a fire, electric shock, or visual
impairment.
Caution
Do not install this product in a location where the operating temperature for your projector
model may be exceeded.
Such an environment may damage the projector.
Install this product in a place free from excessive dust and humidity to prevent the lens or
optical components from becoming dirty.
Do not use excessive force when adjusting this product.
This product may break, resulting in personal injury.
About This Installation Guide
This guide describes how to mount the short-throw projector EB-585Wi/EB-585W/EB-580/EB-575Wi/
EB-575W/EB-570 on a wall.

Using the Product Safely
4
Choosing an Installation Location
Projector installation location
•Carry out power supply wiring work for the installation location of the setting plate in advance.
•Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some kinds of
fluorescent lights could interfere with the remote control of the projector.
•It is recommended to keep connection cable length less than 20 meters to reduce external noise.
•We recommend using stick-on screens or board screens.
•Make sure the projector is installed under the following conditions.
•The projected image is a rectangular shape without any distortion.
•The projector is tilted at an angle of no more than ±3° vertically and horizontally in relation to the screen.
•When using keystone correction, the gradation for vertical and horizontal keystone correction is no more than ±6.
•When using the interactive function (Easy Interactive Function), install so that the projected image is within reach
(EB-585Wi/575Wi only).
•Do not install the projector or the screen in a location subject to direct sunlight. If the projector or the screen are
subject to direct sunlight, the interactive function may not operate correctly (EB-585Wi/575Wi only).

Contents
5
Using the Product Safely
SafetyInstructions .................... 1
Safetyindications .......................1
ExplanationofSymbols ................... 1
SafetyPrecautionsforInstallation ............ 1
AboutThisInstallationGuide ............... 3
ChoosinganInstallationLocation ...... 4
Projectorinstallationlocation ............... 4
Installation Guide
InstallationWorkFlow ................ 6
Package Contents . . ................... 7
Settingplate ........................... 7
Specifications . . . . . ................... 8
Settingplate ........................... 8
Wallplate ........................... 8
Verticalslideadjustmentrange ............ 9
Horizontalslideadjustmentrange .......... 9
Forward/backward slide adjustment range
................................... 9
ProjectionDistanceTable ............ 11
FiguresofInstallationDimensions ........... 11
Interactive whiteboard list (EB-585W/
580/575W/570only) ................... 12
When Projected Image is Smaller than 75 Inches
.................................... 13
EB-585Wi/585W/575Wi/575W (16:10
projectedimage) ..................... 14
EB-585Wi/585W/575Wi/575W (16:9
projectedimage) ..................... 14
EB-585Wi/585W/575Wi/575W (4:3
projectedimage) ..................... 15
EB-580/570(4:3projectedimage).........17
EB-580/570(16:9projectedimage)........17
EB-580/570(16:10projectedimage).......18
When Projected Image is Larger than 75 Inches
.................................... 19
EB-585Wi/585W/575Wi/575W (16:10
projectedimage) ..................... 20
EB-585Wi/585W/575Wi/575W (16:9
projectedimage) ..................... 21
EB-585Wi/585W/575Wi/575W (4:3
projectedimage) ..................... 22
EB-580/570(4:3projectedimage).........23
EB-580/570(16:9projectedimage)........23
EB-580/570(16:10projectedimage).......24
InstallingtheSettingPlate ........... 26
ConnectingDevices ..................... 26
Necessarycables ..................... 26
InstallationProcedure ................... 27
Disassembletheparts................. 27
Assembletheparts ...................27
Installthewallplateonthewall..........29
Determine the projection distance, and then
pass the cables through the setting plate . . . . 31
Attaching the setting plate to the wall plate
.................................. 33
Securing the projector to the setting plate
.................................. 35
AdjustingtheProjectedImage .............37
AdjustingtheProjectionPosition.........37
Fine-tuningtheFocus.................42
Calibrating the Pen (EB-585Wi/575Wi only)
.................................. 44
AttachingtheCovers .................... 48
Appendix
BatchSetupFunction ................ 50
SetupUsingaUSBflashdrive .............. 50
SavingsettingstotheUSBflashdrive......50
Reflecting saved settings to other projectors
.................................. 51
Setup by Connecting the Computer and
ProjectorwithaUSBCable ................ 52
Savingsettingstoacomputer ............ 53
Reflecting saved settings to other projectors
.................................. 53
WhenSetupFails ....................... 55
Using the Interactive Function when
Multiple Projectors are Installed . . . . . . 56
AttachingaSecurityCable ............ 57
GeneralNotice ...................... 58

Installation Guide
6
Installation Work Flow
Follow the procedures below to mount the projector on a wall.
a
Installing the Setting Plate and the Projector (sp.26)
b
Adjusting the Projected Image (sp.37)
c
Calibrating the Interactive Pen (EB-585Wi/575Wi only) (sp.44)

Installation Guide
7
Package Contents
Setting plate
The following supplied items are necessary to mount the projector on a wall. Confirm that you have all items
before beginning.
Setting plate Hexagonal axis Wall plate
Wall plate cover 3-axis adjustment unit
*The slide plate (
ᵟ
) is secured dur‐
ing shipping.
Template sheet
(for installing the wall plate)
End cap Hexagon wrench (for M4) Open-ended spanner
13 mm (for M8 and M6),
6 mm (for hexagonal axis)
Shape Name Quan‐
tity
Application
M4 x 12 mm hexagon socket head cap bolt
with washer/spring washer
6Forwallplateassembly
4 For 3-axis adjustment unit/arm installation
4 For slide plate/projector installation
2 For slide plate/3-axis adjustment unit installa‐
tion (attached during shipping)
M6 x 20 mm hexagon shoulder head bolt
with washer/spring washer
1 For setting plate/wall plate installation
M6 x 20 mm cross recessed head shoulder
screws with plastic washers
3
•Use the bolts or screws supplied with this product to install it as directed in this guide. Do not substitute these bolts
with any other types.
•You need to use commercially available M10 x 60 mm anchors (at least 3) to attach the wall plate to the wall.
•Gather the tools and parts you need before you begin installation.

Installation Guide
8
Specifications
Setting plate
Item Specification Remark Reference
Page
Setting plate weight Approx. 8.1 kg Setting plate (3.0 kg), 3-axis adjustment unit
(1.2 kg), slide plate (0.8 kg), wall plate (2.7 kg),
wall plate cover and end cap (0.4 kg)
Maximum load capacity 7 kg
Forward/backward slide ad‐
justment range
0 to 360 mm Arm slide adjustment range: 0 to 273 mm
Adjustment for 3-axis adjustment unit instal‐
lation position: 87 mm
See the fig‐
ure below
Vertical slide adjustment range ±38 mm See the fig‐
ure below
Horizontal roll adjustment
range
±3° Fine adjustments possible with adjustment
dial
sp.37
Horizontal rotation adjustment
range
±8° Fine adjustments possible with adjustment
dial
sp.37
Vertical tilt adjustment range ±3° Fine adjustments possible with adjustment
dial
sp.37
Horizontal slide adjustment
range
±45 mm See the fig‐
ure below
Wall plate
The following figure shows three wall plates connected to form one plate (separate when shipped).
[Unit: mm]
*Offset value for the position of the center of the projected image and the center of the wall plate

Installation Guide
9
Cable routing holes
When routing cables to connect to the projector through a wall, use positions (
ᵟ
) and ( ) in the following
figure as the cable routing holes.
Vertical slide adjustment range
[Unit: mm]
Horizontal slide adjustment range
[Unit: mm]
Forward/backward slide adjustment range
Arm slide adjustment range
[Unit: mm]

Installation Guide
10
Adjustment range for 3-axis adjustment unit installation position
[Unit: mm]

Installation Guide
11
Projection Distance Table
Figures of Installation Dimensions
To find the appropriate screen size, see the following figures when installing. The values are only rough
estimates.
The recommended range for the projection distance (a) is 62 to 311 mm.
The offset value for the position of the center of the projected image and the center of the wall plate is 70.5
mm.
When the projected image size (S) is 75 inches or more, the scale on the arm slide (b) is equal to the projection
distance (a).
The numbers for (a) and (b) differ if the projected image size (S) is less than 75 inches.
[Unit: mm]
:Projected image size :Wall plate
:Minimum projection distance (Wide: maxi‐
mum zoom)
to maximum (Tele: minimum zoom)
:Screen
:Numbers on the arm slide scale
:Distance from projected image to wall plate
:Height of projected image
:Distance from surface of screen to wall (100
mm or less)
Aspect ratio for standard projected image (EB-585Wi/585W/575Wi/575W)

Installation Guide
12
Aspect ratio for standard projected image (EB-580/570)
Interactive whiteboard list (EB-585W/580/575W/570 only)
When you have already installed an interactive board, check the size of the whiteboards below, and then
refer to the projection distance table.
Projected Im‐
age Size
16:10 4:3 16:9
57" - PolyVision TS410 -
60" - Hitachi
®
Cambridge board60
RM Classboard2 60
INTERWRITE BOARD 1060
INTERWRITE Dual board 1260
-
63" - Hitachi
®
Starboard FX- 63 -
64" - SMART Board 660
Promethean ActivBoard 164
-
66" - TeamBoard RT
TMWM5422CL/EM
-
71" - - INTERWRITE BOARD 1071
75" PolyVision
®
eno2650 - -
77" - HitachiCambridge board77
Hitachi Starboard FX DUO 77
SMART Board680
SMART BoardX880
INTERWRITE
®
BOARD 1077
TeamBoard RT TMWM6250CL/
EM
INTERWRITE Dual board 1277
77.5" - RM Classboard2 77.5 -
78" PolyVision TS 600/ TS620 /
TSL620
PolyVisionTS610
Promethean ActivBoard 178 /
378
-

Installation Guide
13
Projected Im‐
age Size
16:10 4:3 16:9
79" - INTERWRITE Dual board 1279 -
80" - - RM Classboard 85
82" - - Hitachi Starboard FX-82Wide
85" TeamBoard RT TMWM7450EM - INTERWRITE BOARD 1085
INTERWRITE Dual board 1285
87" SMART Board
™
685
SMART BoardX 885
Promethean ActivBoard 387
Promethean ActivBoard 587
pro
--
88" Hitachi Starboard FX DUO-88W - -
89" - INTERWRITE Dual board 1289 -
93" - - PolyVision ENO 2810
94" - - SMART Board 690
95" - - INTERWRITE BOARD 1095
INTERWRITE Dual Board 1295
Promethean ActivBoard 395
Promethean ActivBoard 595
pro
When Projected Image is Smaller than 75 Inches
Mount the 3-axis adjustment unit at the position marked with a stamp (
ᵟ
).
The projection distance table provides the figures when mounting the 3-axis adjustment unit at the position
marked with a stamp (
ᵟ
). The numbers on the arm slide scale (b) differ from the projection distance (a).
The distance (c) from the projected image to the wall plate is the number given when the vertical slide is set
to the standard position ( ).
Match the notch on the setting plate to the position of the stamp on the wall plate.

Installation Guide
14
EB-585Wi/585W/575Wi/575W (16:10 projected image)
[Unit: cm]
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
60" 129.2x80.8 6.2 - 19.3 14.9 - 28.0 17.4 80.8
61" 131.4x82.1 6.9 - 20.1 15.6 - 28.8 17.7 82.1
62" 133.5x83.5 7.5 - 20.9 16.2 - 29.6 17.9 83.5
63" 135.7x84.8 8.1 - 21.8 16.8 - 30.5 18.2 84.8
64" 137.9x86.2 8.7 - 22.6 17.4 - 31.3 18.5 86.2
65" 140.0x87.5 9.3 - 23.5 18.0 - 32.2 18.7 87.5
66" 142.2x88.8 10.0 - 24.3 18.7 - 33.0 19.0 88.8
67" 144.3x90.2 10.6 - 25.1 19.3 - 33.8 19.3 90.2
68" 146.5x91.5 11.2 - 26.0 19.9 - 34.7 19.5 91.5
69" 148.6x92.9 11.8 - 26.8 20.5 - 35.5 19.8 92.9
70" 150.8x94.2 12.4 - 27.6 21.1 - 36.3 20.1 94.2
71" 152.9x95.6 13.1 - 28.5 21.8 - 37.2 20.3 95.6
72" 155.1x96.9 13.7 - 29.3 22.4 - 38.0 20.6 96.9
73" 157.2x98.3 14.3 - 30.2 23.0 - 38.9 20.9 98.3
74" 159.4x99.6 14.9 - 31.0 23.6 - 39.7 21.1 99.6
Images smaller than 60 inches are not projected correctly.
EB-585Wi/585W/575Wi/575W (16:9 projected image)
[Unit: cm]
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
59" 130.6x73.5 6.6 - 19.8 15.3 - 28.5 21.7 73.5
60" 132.8x74.7 7.3 - 20.7 16.0 - 29.4 22.0 74.7
61" 135.0x76.0 7.9 - 21.5 16.6 - 30.2 22.3 76.0
62" 137.3x77.2 8.6 - 22.4 17.3 - 31.1 22.7 77.2
63" 139.5x78.5 9.2 - 23.3 17.9 - 32.0 23.0 78.5
64" 141.7x79.7 9.8 - 24.1 18.5 - 32.8 23.4 79.7
65" 143.9x80.9 10.5 - 25.0 19.2 - 33.7 23.7 80.9
66" 146.1x82.2 11.1 - 25.8 19.8 - 34.5 24.1 82.2

Installation Guide
15
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
67" 148.3x83.4 11.7 - 26.7 20.4 - 35.4 24.4 83.4
68" 150.5x84.7 12.4 - 27.6 21.1 - 36.3 24.8 84.7
69" 152.8x85.9 13.0 - 28.4 21.7 - 37.1 25.1 85.9
70" 155.0x87.2 13.7 - 29.3 22.4 - 38.0 25.4 87.2
71" 157.2x88.4 14.3 - 30.1 23.0 - 38.8 25.8 88.4
72" 159.4x89.7 14.9 - 31.0 23.6 - 39.7 26.1 89.7
73" 161.6x90.9 15.6 - 31.1 24.3 - 39.8 26.5 90.9
74" 163.8x92.1 16.2 - 31.1 24.9 - 39.8 26.8 92.1
Images smaller than 59 inches are not projected correctly.
EB-585Wi/585W/575Wi/575W (4:3 projected image)
[Unit: cm]
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
53" 107.7x80.8 6.2 - 19.3 14.9 - 28.0 17.4 80.8
54" 109.7x82.3 6.9 - 20.2 15.6 - 28.9 17.7 82.3
55" 111.8x83.8 7.6 - 21.2 16.3 - 29.9 18.0 83.8
56" 113.8x85.3 8.3 - 22.1 17.0 - 30.8 18.3 85.3
57" 115.8x86.9 9.1 - 23.1 17.8 - 31.8 18.6 86.9
58" 117.9x88.4 9.8 - 24.0 18.5 - 32.7 18.9 88.4
59" 119.9x89.9 10.5 - 25.0 19.2 - 33.7 19.2 89.9
60" 121.9x91.4 11.2 - 25.9 19.9 - 34.6 19.5 91.4
61" 124.0x93.0 11.9 - 26.9 20.6 - 35.6 19.8 93.0
62" 126.0x94.5 12.6 - 27.8 21.3 - 36.5 20.1 94.5
63" 128.0x96.0 13.3 - 28.8 22.0 - 37.5 20.4 96.0
64" 130.0x97.5 14.0 - 29.7 22.7 - 38.4 20.7 97.5
65" 132.1x99.1 14.7 - 30.7 23.4 - 39.4 21.0 99.1
66" 134.1x100.6 15.4 - 31.1 24.1 - 39.8 21.3 100.6
67" 136.1x102.1 16.1 - 31.1 24.8 - 39.8 21.6 102.1
68" 138.2x103.6 16.8 - 31.1 25.5 - 39.8 21.9 103.6
69" 140.2x105.2 17.5 - 31.1 26.2 - 39.8 22.2 105.2
70" 142.2x106.7 18.2 - 31.1 26.9 - 39.8 22.5 106.7

Installation Guide
16
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
71" 144.3x108.2 18.9 - 31.1 27.6 - 39.8 22.8 108.2
72" 146.3x109.7 19.6 - 31.1 28.3 - 39.8 23.2 109.7
73" 148.3x111.3 20.3 - 31.1 29.0 - 39.8 23.5 111.3
74" 150.4x112.8 21.0 - 31.1 29.7 - 39.8 23.8 112.8
Images smaller than 53 inches are not projected correctly.

Installation Guide
17
EB-580/570 (4:3 projected image)
[Unit: cm]
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
56" 113.8x85.3 6.3 - 19.3 15.0 - 28.0 15.2 85.3
57" 115.8x86.9 6.9 - 20.2 15.6 - 28.9 15.4 86.9
58" 117.9x88.4 7.6 - 21.1 16.3 - 29.8 15.6 88.4
59" 119.9x89.9 8.3 - 22.0 17.0 - 30.7 15.9 89.9
60" 121.9x91.4 8.9 - 22.9 17.6 - 31.6 16.1 91.4
61" 124.0x93.0 9.6 - 23.8 18.3 - 32.5 16.4 93.0
62" 126.0x94.5 10.3 - 24.7 19.0 - 33.4 16.6 94.5
63" 128.0x96.0 10.9 - 25.6 19.6 - 34.3 16.9 96.0
64" 130.0x97.5 11.6 - 26.5 20.3 - 35.2 17.1 97.5
65" 132.1x99.1 12.2 - 27.4 20.9 - 36.1 17.4 99.1
66" 134.1x100.6 12.9 - 28.3 21.6 - 37.0 17.6 100.6
67" 136.1x102.1 13.6 - 29.2 22.3 - 37.9 17.9 102.1
68" 138.2x103.6 14.2 - 30.1 22.9 - 38.8 18.1 103.6
69" 140.2x105.2 14.9 - 31.0 23.6 - 39.7 18.3 105.2
70" 142.2x106.7 15.6 - 31.1 24.3 - 39.8 18.6 106.7
71" 144.3x108.2 16.2 - 31.1 24.9 - 39.8 18.8 108.2
72" 146.3x109.7 16.9 - 31.1 25.6 - 39.8 19.1 109.7
73" 148.3x111.3 17.6 - 31.1 26.3 - 39.8 19.3 111.3
74" 150.4x112.8 18.2 - 31.1 26.9 - 39.8 19.6 112.8
Images smaller than 56 inches are not projected correctly.
EB-580/570 (16:9 projected image)
[Unit: cm]
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
52" 115.1x64.8 6.7 - 19.9 15.4 - 28.6 26.1 64.8
53" 117.3x66.0 7.4 - 20.9 16.1 - 29.6 26.6 66.0
54" 119.5x67.2 8.1 - 21.8 16.8 - 30.5 27.1 67.2
55" 121.8x68.5 8.9 - 22.8 17.6 - 31.5 27.5 68.5

Installation Guide
18
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
56" 124.0x69.7 9.6 - 23.8 18.3 - 32.5 28.0 69.7
57" 126.2x71.0 10.3 - 24.8 19.0 - 33.5 28.5 71.0
58" 128.4x72.2 11.0 - 25.8 19.7 - 34.5 29.0 72.2
59" 130.6x73.5 11.8 - 26.7 20.5 - 35.4 29.4 73.5
60" 132.8x74.7 12.5 - 27.7 21.2 - 36.4 29.9 74.7
61" 135.0x76.0 13.2 - 28.7 21.9 - 37.4 30.4 76.0
62" 137.3x77.2 13.9 - 29.7 22.6 - 38.4 30.9 77.2
63" 139.5x78.5 14.7 - 30.6 23.4 - 39.3 31.3 78.5
64" 141.7x79.7 15.4 - 31.1 24.1 - 39.8 31.8 79.7
65" 143.9x80.9 16.1 - 31.1 24.8 - 39.8 32.3 80.9
66" 146.1x82.2 16.8 - 31.1 25.5 - 39.8 32.8 82.2
67" 148.3x83.4 17.6 - 31.1 26.3 - 39.8 33.2 83.4
68" 150.5x84.7 18.3 - 31.1 27.0 - 39.8 33.7 84.7
69" 152.8x85.9 19.0 - 31.1 27.7 - 39.8 34.2 85.9
70" 155.0x87.2 19.7 - 31.1 28.4 - 39.8 34.7 87.2
71" 157.2x88.4 20.5 - 31.1 29.2 - 39.8 35.1 88.4
72" 159.4x89.7 21.2 - 31.1 29.9 - 39.8 35.6 89.7
73" 161.6x90.9 21.9 - 31.1 30.6 - 39.8 36.1 90.9
74" 163.8x92.1 22.6 - 31.1 31.3 - 39.8 36.6 92.1
Images smaller than 52 inches are not projected correctly.
EB-580/570 (16:10 projected image)
[Unit: cm]
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
53" 114.2x71.3 6.4 - 19.5 15.1 - 28.2 22.3 71.3
54" 116.3x72.7 7.1 - 20.4 15.8 - 29.1 22.7 72.7
55" 118.5x74.0 7.8 - 21.4 16.5 - 30.1 23.1 74.0
56" 120.6x75.4 8.5 - 22.3 17.2 - 31.0 23.5 75.4
57" 122.8x76.7 9.2 - 23.3 17.9 - 32.0 23.9 76.7
58" 124.9x78.1 9.9 - 24.2 18.6 - 32.9 24.3 78.1
59" 127.1x79.4 10.6 - 25.2 19.3 - 33.9 24.7 79.4

Installation Guide
19
S
Projected image size
a
Projection Dis‐
tance
Minimum (Wide)
to Maximum
(Tele)
b
Numbers on the
arm slide scale
c
Distance from
projected image
to wall plate
h
Height of projec‐
ted image
60" 129.2x80.8 11.3 - 26.1 20.0 - 34.8 25.1 80.8
61" 131.4x82.1 12.0 - 27.1 20.7 - 35.8 25.5 82.1
62" 133.5x83.5 12.7 - 28.0 21.4 - 36.7 25.9 83.5
63" 135.7x84.8 13.4 - 29.0 22.1 - 37.7 26.3 84.8
64" 137.9x86.2 14.1 - 29.9 22.8 - 38.6 26.7 86.2
65" 140.0x87.5 14.8 - 30.9 23.5 - 39.6 27.1 87.5
66" 142.2x88.8 15.5 - 31.1 24.2 - 39.8 27.5 88.8
67" 144.3x90.2 16.3 - 31.1 25.0 - 39.8 27.9 90.2
68" 146.5x91.5 17.0 - 31.1 25.7 - 39.8 28.3 91.5
69" 148.6x92.9 17.7 - 31.1 26.4 - 39.8 28.7 92.9
70" 150.8x94.2 18.4 - 31.1 27.1 - 39.8 29.1 94.2
71" 152.9x95.6 19.1 - 31.1 27.8 - 39.8 29.4 95.6
72" 155.1x96.9 19.8 - 31.1 28.5 - 39.8 29.8 96.9
73" 157.2x98.3 20.5 - 31.1 29.2 - 39.8 30.2 98.3
74" 159.4x99.6 21.2 - 31.1 29.9 - 39.8 30.6 99.6
Images smaller than 53 inches are not projected correctly.
c
•The values are only rough estimates. The value may differ depending on the location where you place
the projector.
•When projecting in Tele, the quality of the projected images may decrease.
•When using EB-585Wi/585W/575Wi/575W to project images at 4:3, the images are resized
automatically and the quality of the projected images may decrease.
When Projected Image is Larger than 75 Inches
Mount the 3-axis adjustment unit at the position marked with a stamp (
ᵟ
).
The projection distance table provides the figures when mounting the 3-axis adjustment unit at the position
marked with a stamp (
ᵟ
). The numbers on the arm slide scale (b) is the same as the projection
distance (a).
The distance (c) from the projected image to the wall plate is the number given when the vertical slide is set
to the standard position ( ).