Epson Perfection V200 Photo User manual

Epson Perfection V200 Photo
7/07 Epson Perfection V200 Photo - 1
Scanner Parts
Scanner Specifications
General
Mechanical
a
c
b
b
a
c
e
d
c
a
b
P
Power/
]Start button
aScan to PDF
button
Status light
{Copy button
|Scan to E-mail button
Removable
Document mat
Document
table
Carriage
DC inlet
USB interface
connector
USB interface
connector
Scanner cover
a
Transparency
unit window
Scanner type Flatbed color
Photoelectric device Epson MatrixCCD®(12-line sensor)
Effective pixels 40,800 ×56,160 pixels at 4800 dpi
Document size Documents or photos:
8.5 ×11.7 inches (216 ×297 mm)
US letter or A4 size
Film or slides:
35mm film strips (6 frames at a time);
35mm slides (4 slides at a time)
Scanning resolution 4800 dpi (main scan)
9600 dpi with Micro Step Drive ™
(sub scan)
Output resolution 50 to 6400, 9600, and 12800 dpi
(50 to 6400 dpi in 1 dpi increments)
Image data 16 bits per pixel per color internal
16 bits per pixel per color external
Interface One USB 2.0 Hi-Speed port
(USB 1.1 compatible)
Light source White cold cathode fluorescent lamp
Dimensions Width: 16.9 inches (430 mm)
Depth: 11 inches (280 mm)
Height: 2.2 inches (57 mm)
Weight Approx. 5.7 lb (2.6 kg)
Film holder

Epson Perfection V200 Photo
2 - Epson Perfection V200 Photo 7/07
Electrical
Note:
Check the label on the AC adapter or on the back of the scanner for
voltage information.
Scanner
AC Adapter (A391UC)
Environmental
USB Interface
Standards and Approvals
Scanner
AC Adapter
Using the Scanner Buttons
Before using the scanner buttons, make sure you have installed
Epson Scan and the other software that came with the scanner.
For details on using the buttons, see the on-screen User’s Guide.
Placing Documents or Photos
Caution:
Do not place heavy objects on the document table glass and do not
press the glass with too much force.
1. Open the scanner cover.
Make sure the document mat is installed inside the cover. If
it is not installed, see page 6 for instructions.
Rated voltage DC 13.5 V
Rated current 1.5 A
Power consumption 16.5 W operating
14 W stand-by mode
3.6 W sleep mode
0.5 W power off
Rated input voltage AC 100 to 120 V
Rated input current 0.6 A
Ratedfrequency 50to60Hz
Rated output voltage DC 13.5 V
Rated output current 1.5 A
Temperature Operating 50 to 95 °F (10 to 35 °C)
Storage –13 to 140 °F (–25 to 60 °C)
Humidity Operating 10 to 80%, without condensation
Storage 10 to 85%, without condensation
Operating
conditions
Ordinary office or home
conditions. Avoid operating the
scanner in direct sunlight, near a
strong light source, or in extremely
dusty conditions.
Interface type Universal Serial Bus Specification Revision
2.0
Interface standard Full Speed mode (12 Mbits per second)
and Hi-Speed mode (480 Mbits per
second) of Universal Serial Bus
Specification Revision 2.0.
Connector type One Type B port
EMC FCC Part 15 Subpart B Class B
CAN/CSA-CEI/IEC CISPR 22
Safety UL60950-1
CAN/CSA-22.2 No. 60950-1-03
EMC FCC Part 15 Subpart B Class B
CAN/CSA-CEI/IEC CISPR 22 Class B
Button Function
PPower/]Start Turns the scanner on if pressed once while the
scanner is off.
Epson Scan starts if pressed once while the
scanner is on.
Turns the scanner off if held down for 3 seconds
while the scanner is on. (You cannot turn the
scanner off when the scanning software is
running.)
{Copy The Copy Utility starts.
|Scan to E-mail Epson Scan automatically scans, then the Send File
Via E-mail window appears.
aScan to PDF The Scan to PDF window appears.
a
document
mat

Epson Perfection V200 Photo
7/07 Epson Perfection V200 Photo - 3
2. Place your document or photo face-down on the document
table. Make sure the upper left corner of the document or
photo is against the front right corner of the scanner, next to
the arrow mark.
An area 0.12 inch (3 mm) from the horizontal and the
vertical sides of the scanner glass cannot be scanned. If you
place a document in the corner of the document table,
move it up and in slightly to avoid cropping.
3. If you are scanning multiple photos at once, position each
photo at least 0.8 inch (20 mm) apart from the others.
4. Close the scanner cover gently so that your original does not
move.
Note:
Always keep the document table clean.
Do not leave photos on the document table for an extended
period of time as they may stick to the glass.
Placing Large or Thick Documents
When you scan a large or thick document, you can open the
scanner cover all the way, so that it lies flat behind the scanner.
1. Open the scanner cover.
2. Pull the scanner cover straight up.
3. Lay the cover down flat behind the scanner.
Note:
When scanning with the scanner cover open, gently press down
on your document to flatten it.
4. When you are finished scanning, replace the scanner cover.
a
b
Maximum unreadable area of
0.12 inch (3 mm)
Maximum
unreadable area of
0.12 inch (3 mm)

Epson Perfection V200 Photo
4 - Epson Perfection V200 Photo 7/07
Placing Film or Slides
Removing the Document Mat
To scan film strips or slides, you need to remove the document
mat from the scanner cover. This uncovers the transparency
unit window so your scanner can use it to scan your film or
slides.
1. Open the scanner cover and gently slide up the document
mat to remove it.
2. Use a soft microfiber cloth to wipe the transparency unit
window and the document table before placing your film or
slides.
To place film for scanning, see the next section.
To place slides for scanning, see page 5.
Placing Film in the Holder
1. Open the cover of the 35mm film strip holder.
2. Slide your film strip all the way into the film holder with the
shiny base side facing down. Your images and any wording
on the film strip should appear backwards on the side that
faces up. You can scan up to 6 standard 35mm images per
film strip.
Note:
Hold the edge of the film gently when touching the film;
otherwise you may damage the film.
Make sure the white stickers on the back of the film holder and
the areas around them are not scratched, dusty, or covered in
any way. If the areas are obscured, the scanner may have trouble
recognizing your film.
Do not cover the small holes or slots in the film holder.
3. Close the cover and press it down until you hear a click.
Make sure the cover is properly seated and closed all the
way.
a
Transparency
unit window

Epson Perfection V200 Photo
7/07 Epson Perfection V200 Photo - 5
4. Make sure the film strip is placed as shown.
5. Place the film holder on the document table so that it is
aligned as shown. Make sure the tab with the film icon on
the film holder fits into the area with the same icon on the
scanner.
6. Make sure you removed the document mat. See page 4.
7. Close the scanner cover.
When you are finished scanning film, be sure to replace the
document mat before scanning documents or photos. See
page 6.
Placing Slides in the Holder
You can scan up to four 35mm slides at a time using the slide
portion of the film holder.
Note:
Make sure the white stickers on the back of the film holder and the
areas around them are not scratched, dusty, or covered in any way. If
the areas are obscured, the scanner may have trouble recognizing
your slides.
Do not cover the small holes or slots in the film holder.
1. Place the film holder on the document table so that it is
aligned as shown. Make sure the tab with the slide icon on
the film holder fits into the area with the same icon on the
scanner.
2. Place up to four slides in the film holder with the shiny base
side facing down. Your images should appear backwards on
the side that faces up. Your images should be oriented as
shown.
Note:
Make sure you place the long edge of the slide in the film holder
as shown above, for both landscape and portrait-oriented photos.
3. Make sure you removed the document mat. See page 4.
4. Close the scanner cover.
When you are finished scanning slides, be sure to replace
the document mat before scanning documents or photos.
See page 6.

Epson Perfection V200 Photo
6 - Epson Perfection V200 Photo 7/07
Storing the Film Holder
When you are not using the film holder, you can store it inside
the scanner cover.
1. Open the scanner cover and remove the document mat. For
instructions, see page 4.
2. Slide the film holder into the scanner cover.
3. Replace the document mat. See the next section for
instructions.
Replacing the Document Mat
Replace the document mat by sliding it into the notches in the
scanner cover. Make sure the white surface faces outwards.
Scanning and Restoring Photos
Using the Color Restoration feature in Epson Scan, you can
transform old, faded, or badly exposed photos into ones with
true-to-life color. You can restore printed photos, negative film,
or slides automatically as you scan them.
You can use Color Restoration in Epson Scan’s Full Auto,
Home, or Professional Mode. For detailed steps, see the
on-screen User’s Guide.
Full Auto Mode
Home Mode Professional Mode

Epson Perfection V200 Photo
7/07 Epson Perfection V200 Photo - 7
Removing Dust From Photos, Film, or
Slides
Using the Dust Removal feature in Epson Scan’s Full Auto,
Home, or Professional Mode, you can virtually “clean” the dust
marks from printed photos, film, or slides as you scan them. For
detailed steps, see the on-screen User’s Guide.
Fixing Backlit Photos
Using the Backlight Correction feature in Epson Scan’s Home
or Professional Mode, you can remove shadows from photos
that have too much background light. You can fix printed
photos, film, or slides automatically as you scan them. For
detailed steps, see the on-screen User’s Guide.
Note:
Backlight Correction is not available in Full Auto Mode.
Reading the Status Light
If an error occurs, the scanner stops operating and the status
light flashes red. This indicates the scanner is not connected to
your computer properly or your software is not fully installed.
See the Start Here sheet that came with your scanner for
instructions on installing the scanner software and connecting
the scanner to your computer.
If the suggestions above don’t help, press the PPower button
for 3 seconds to turn off the scanner, then turn it on again.
If the Status light is still flashing:
❏The scanner may be malfunctioning.
❏The scanner lamp may need to be replaced.
Contact Epson. See the on-screen User’s Guide for details.
Full Auto Mode
Home Mode Professional Mode
Home Mode Professional Mode

Epson Perfection V200 Photo
8 - Epson Perfection V200 Photo 7/07
Transporting the Scanner
Before you transport the scanner for a long distance or store it
for an extended period of time, the scanner’s carriage needs to
be in the center position to prevent damage.
1. If the carriage is not in the center position of the scanner,
follow these steps.
❏If the scanner is turned on and connected to your
computer, press and hold the |Scan to E-mail and
{Copy buttons simultaneously until the carriage moves
to the center of the scanner.
❏If the scanner is turned off, press the PPower button to
turn on the scanner, connect it to your computer, and
wait about 15 seconds for the computer to recognize the
scanner. Then press and hold the |Scan to E-mail and
{Copy buttons simultaneously until the carriage moves
to the center of the scanner.
2. Press the PPower button for 3 seconds to turn off the
scanner, then unplug the AC adapter.
3. Disconnect the USB cable from the scanner.
4. Attach the packing materials that came with the scanner,
then repack the scanner in its original box or a similar box
that fits the scanner snugly.
Related Documentation
Note:
The availability of manuals varies by location.
CPD-23664 Epson Perfection V200 Photo
Start Here sheet (English)
CPD-23667 Epson Perfection V200 Photo
Start Here sheet (English/French/Spanish)
CPD-23666 Epson Perfection V200 Photo
Notices booklet (English)
CPD-23669 Epson Perfection V200 Photo
Notices booklet (English/French/Spanish)
CPD-23665 Epson Perfection V200 Photo Scanner
Software CD-ROM (English), (includes
on-screen User’s Guide)
CPD-23668 Epson Perfection V200 Photo Scanner
Software CD-ROM (English/French/
Spanish), (includes on-screen User’s Guides)

Epson Perfection V200 Photo
7/07 Epson Perfection V200 Photo - 9