Epygi Leviton OmniTouch 7 User manual

Please Note: This document contains confidential and proprietary information owned by Epygi Technologies, LTD. Any copying, use or disclosure of the document or the information
contained herein without the written permission of Epygi Technologies, LTD. is strictly prohibited.
Copyright © 2003-2015 Epygi Technologies, LTD. All Rights Reserved.
Configuring Leviton OmniTouch 7 Touchscreens
& Helios 2N door stations with the Epygi QX IP
PBX
Abstract: This document describes how to Configure Leviton OmniTouch 7 Touchscreen & Helios 2N door
station with the Epygi QX IP PBX

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 231-Mar-16
Table of Contents
1 Introduction................................................................................................................................................................ 3
2 Requirements and Preparations ............................................................................................................................... 3
3 Configuration ............................................................................................................................................................. 3
3.1 Configuring the Epygi IP PBX............................................................................................................................... 5
3.1.1 Login and configure the IP network settings.............................................................................................................................. 5
3.1.2 Add extensions for IP phones, touchscreens and door stations. ................................................................................................. 7
3.1.3 Create a Ring Group .................................................................................................................................................................. 9
3.1.4 Create a Paging Group ............................................................................................................................................................... 10
3.2 Configuring the 2N Helios IP Force door station................................................................................................. 11
3.2.1 Login and configure the IP network settings.............................................................................................................................. 11
3.2.2 Configure the SIP settings to make and receive calls................................................................................................................. 13
3.3 Configuring Leviton OmniTouch 7 Touchscreen................................................................................................. 16
3.3.1 Configure the OmniTouch 7 Touchscreens from the Dealer PC Access management system................................................... 16
3.3.2 Update the OmniTouch 7 Touchscreen...................................................................................................................................... 19
4 Call Scenarios ............................................................................................................................................................. 19
4.1 Call handling from the OmniTouch 7 Touchpad ................................................................................................. 19
4.1.1 Originating a call from OmniTouch 7 to the 2N Helios Door Station........................................................................................ 19
4.1.2 Operating the door relay from the OmniTouch 7 ....................................................................................................................... 21
4.2 Calls originating from the 2N Helios Door Station .............................................................................................. 22
4.2.1 Call using the quick dial button.................................................................................................................................................. 22
4.2.2 Placing a call to any extension in the Epygi............................................................................................................................... 22
4.2.3 Placing a call to a Ring Group that includes a cell phone. ......................................................................................................... 22
4.2.4 Activating the 2N door lock relay .............................................................................................................................................. 22
5 Troubleshooting and Maintenance Tips .................................................................................................................. 23
5.1 Epygi IP PBX........................................................................................................................................................... 23
5.1.1 System Security ......................................................................................................................................................................... 23
5.1.2 Maintenance and Testing ........................................................................................................................................................... 23
5.2 2N Helios IP Force door station............................................................................................................................. 23
5.2.1 Configuration and Usage Tips.................................................................................................................................................... 23
6 References................................................................................................................................................................... 23

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 331-Mar-16
Introduction
The Leviton home automation solution, featuring the powerful OmniTouch 7 Touchscreen device, can be configured with an Epygi
IP PBX to offer paging and door station control when used with a door station, such as the 2N Helios IP Force. Once configured,
the solution will offer the following scenario possibilities:
1. Calling directly from an OmniTouch 7 Touchscreen to a single device or multiple devices in a ring group, such as phones,
door stations or other OmniTouch 7 Touchscreens. If the called device supports video the OmniTouch 7 Touchscreen will
see the video from the called device.
2. From the door station a call can be placed to a group of devices, such as phones, door stations or several OmniTouch 7
Touchscreens. If the called device supports video the door stations video feed will be seen. On the OmniTouch 7
Touchscreens the video is seen even prior to answer. Using the keypad from the device that answered the call, door access
can be granted by pressing a digit(s) to unlock the door control. If the call is answered by the OmniTouch 7 Touchscreen an
activation key is available to operate the door relay.
Requirements and Preparations
This guide will use the following components:
•Epygi QX IP PBX: QX200 IP PBX software version 6.1.5 or higher. This guide is also relevant to the QX50 and QX2000 IP
PBXs.
•Leviton:
The Leviton OmniTouch 7 Touchscreen using software version 1.14 or higher.
For configuring the Leviton devices Dealer PC Access using software version 3.15.0.803 or higher.
Omni pro II using software version 3.14A or higher.
•2N Helios IP Force door station using software version: 1.13.1.288.3. A software license key is required to enable the HTTP
API interface to allow the door relay to be operated from the OmniTouch 7 Touchscreen.
•All devices should be connected in a similar configuration as shown in Figure 1.
Configuration
Since the Epygi has a built-in firewall and DHCP server the system has a WAN port as well as a LAN port. The WAN port can be
used to connect to an existing private network or even to a public network. By default, the WAN port will receive an IP address if
connected to a local network with a DHCP server. The LAN port can be used as the DHCP server for the network. By default, the
LAN DHCP server will be disabled.
In this configuration guide the details provided are for a network that has an existing router that will also be the DHCP server on
the network. The Epygi IP PBX, the 2N Helios door station and the Leviton OmniTouch 7 Touchscreen will all be connected to
have an IP from the network DHCP server. See figure 1 for the network configuration.
The devices will be configured in the following order:
1. Epygi QX200
2. 2N Helios IP Force door station
3. Leviton OmniTouch 7 Touchscreen

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 431-Mar-16
Figure 1: IP PBX connected to the network via WAN port, Firewall/Router acting as the DHCP server to the Epygi,
OmniTouch 7 Touchscreen, doorstation and IP phones
The Epygi IP PBX WAN port can also be connected directly to the internet and serve as the DHCP server for the local network
(Figure 2). In this case the OmniTouch 7 Touchscreen, doorstation and IP phones would be connected to the Epygi IP PBX LAN
port.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 531-Mar-16
Figure 2: Devices connected to Epygi IP PBX LAN. The Epygi is the Firewall/Router acting as the DHCP server to the
OmniTouch 7 Touchscreen, doorstation and IP phones, all connected on the Epygi LAN
Configuring the Epygi IP PBX
Login and configure the IP network settings.
To connect to the LAN IP address of the system (172.30.0.1) you will need to set a static IP address on your PC to be in the same
subnet (e.g. 172.30.0.100):
1. Using a standard network patch cable, connect the Epygi WAN to the local network.
2. Using a second network patch cable, connect the PC being using to configure the system to the LAN port of the Epygi.
3. Change the PC’s ethernet adapter settings to have a static IP address (e.g. 172.30.0.100) to be in the same subnet as the
Epygi.
4. Open a browser and connect to the Epygi LAN using 172.30.0.1.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 631-Mar-16
5. Enter the default Username (admin) and Password (19) and click Log In.
6. Click Setup -Basic Setup and select System (LAN) to start the System Configuration Wizard.
•If needed, change the LAN IP address or leave at the default of 172.30.0.1 and enable the DHCP server to provide IP
addresses on the LAN. Enabling the DHCP server would be needed for the optional configuration, Figure 2.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 731-Mar-16
•Click Finish to begin making the changes and initializing the rollback feature. When complete a Confirm Settings page will
appear- click on Ok. If you changed the IP address of the LAN port you will not see the confirmation page until you reconnect
using the new IP. You have 20 minutes to confirm the settings or it will roll back to the previous settings
7. Before configuring the WAN IP you can check to see if the system has already received an IP by going to the Status –
System Status – Network menu. The settings displayed may be helpful before proceeding to the next steps of assigning a
static IP. Click Setup -Basic Setup and select Internet (WAN) to start the Internet Configuration Wizard.
•Assign the system WAN port to a static IP address, subnet mask and default gateway. The fixed name server (DNS server) is
only needed if a DNS server is available for the network.
•Click Finish to finalize the changes.
•At this point you would be able to login to the Epygi by connecting via the WAN or LAN IP address after resetting your PC
adapter connection settings back to DHCP.
8. For using the optional configuration (figure 2), go to Interfaces, IP Lines, IP Line Settings and change the setting
“Configure IP phones from:”, set to LAN. Pressing Save will require a reboot of the unit to update this setting. Changing
this setting will allow the Epygi to provide the proper interface IP address to the devices being configured by the system.
Add extensions for IP phones, touchscreens and door stations.
1. Click Extensions – Extensions and press Save to leave at the default of three digit extension numbering. Extensions can
be deleted and re-added later if needed. The extensions management page is shown, figure 3. Each extension has been
assigned to either an FXS port or an IP Line. The IP phones, Touchscreens and door stations will be configured to the
extensions with the IP Lines. If needed, an IP Line can be re-assigned from one extension to another extension. In the
example below, if extension 102 will be used for a door station the Attached Line will need to be changed from FXS 1 to an
IP Line.
2. Check the box beside all of the extensions that will be used (touchscreens, IP phones, door stations, etc) and click Edit.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 831-Mar-16
3. Click on Codec Settings and put a check beside the modify fields, G.711u, G.729a and H.264 and press Save.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 931-Mar-16
4. Check the box beside the first extension to be configured (e.g. ext. 103) and click Edit.
5. In the General Settings enter the desired Display Name (e.g. Touchscreen1) and press Save. The Display Name will be
used for Caller Id purposes. It is not necessary to reboot the phone now.
Configure the SIP registration settings for the IP phones, Touchscreens and door stations.
6. From the Edit extension, General Settings click on Go to Line Settings to configure the SIP settings for the device. Set the
Phone Model to Other for touchscreens and door stations. For supported IP Phones, choose the Phone Model from the
dropdown and enter the MAC Address of the IP Phone. Enter the device SIP Registration Username. You can use the
default or set your own. Enter the Registration Password by creating your own or preferably, click on Generate Password
and select one.
CRITICAL NOTE:Make a note of the Username and Password as they will be needed when configuring the touchscreen
and door stations.
7. For IP phones, reset the phone to factory default to complete the configuration.
8. Repeat the above listed steps for each IP phone, Touchscreen and door station that will be connecting to the Epygi IP PBX.
Create a Ring Group
1. From the Dashboard menu click Extensions, Extensions to go to the Extensions Management menu.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 10 31-Mar-16
2. Click Add and add a new extension number (e.g. extension 400), leave the Type set to User Extension. Press Save. In the
General Settings enter the Display Name of Ring Group (or other desired name), and click Save. Press Go Back to return
to the General Settings.
3. Click Go To User Settings and then select Caller ID Services.Click Any Address and then select Many Extension
Ringing to define the ring group.
4. Check the boxes beside each extension (IP Phones and Touchscreens) that will be included in the ring group and click
Enable/Disable. Click Enable Service and press Save to activate the MER option.
CRITICAL NOTE: DO NOT CHECK THE BOXES FOR ANY DOOR STATIONS.
Create a Paging Group
1. From the Dashboard menu click Extensions, Extensions to go to the Extensions Management menu.
2. Click Add and add a new extension number (e.g. ext. 401), set the Type to Paging Group. Press Save. In the General
Settings enter the Display Name of Paging Group (or other desired name), and click Save.
3. Click on Edit Paging Group and put a check beside each of the extensions to be paged and click Enable.
CRITICAL NOTE: DO NOT CHECK THE BOXES FOR ANY DOOR STATIONS.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 11 31-Mar-16
Configuring the 2N Helios IP Force door station
Login and configure the IP network settings.
Log in to the 2N Helios IP Force device by entering the IP address in a browser. By default, DHCP is not enabled on the unit so it
will not receive an IP address from the local DHCP server. To initially access the unit you can connect your PC directly to the
device and enter the IP address of the unit. To find the IP address see the Troubleshooting and Maintenance Tips for the 2N Helios
at the end of this guide.
1. Open a browser, enter in the URL for the door station and hit Enter.
2. Enter in the User Name (default is admin) and Password (default is 2n), and hit Login.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 12 31-Mar-16
3. Click on System and then Network.
4. Set/Enter in the following:
•Uncheck DHCP.
•Click on/Expand Manual Settings.
•Enter in the desired IP Address.
•Enter in the Subnet Mask.
•Enter in the Default Gateway.
•Enter in the Primary (and Secondary, if desired) DNS.
•Click on Apply.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 13 31-Mar-16
Configure the SIP settings to make and receive calls
1. Click on Services (purple icon) and then select Phone.
2. Enter the following:
•Display Name – recommend using the name assigned to the extension created in the Epygi.
•Phone Number (ID) – this is the SIP Registration Username assigned to the door station in the Epygi IP Line Settings.
•Domain – enter in the network domain.
•Expand the Authentication tab and enable Use Authentication Id
•Authentication Id: this is the SIP Registration Username assigned to the door station in the Epygi IP Line Settings.
•Password: this is the SIP Registration Password assigned to the door station in the Epygi IP Line Settings.
•Check the box for Registration enabled.
•Registrar Address – this is the IP address for the Epygi.
•Registrar Port – you can use the default value (5060).
•Registration Expires – Recommend to set to 3600 s (1 hour).
•Click on Apply.
•Click on the Video tab and ensure that Codec 1 is set to H.264.
•Click on Apply.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 14 31-Mar-16
•
3. While still on the Services tab, go to HTTP API and make the following changes:
•Set the Connection Type for Camera API to "Unsecure (TCP)".
•If the relay on the 2N will be used (must have a license to use this feature), set the Switch API to "Unsecure (TCP)".

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 15 31-Mar-16
4. Click on Directory (blue icon) and select Users.
5. Enter in the following:
•User Basic Information Name – Enter in the name of the door station set in the Epygi.
•User Phone Numbers Number 1 Phone Number – enter in the number for the “Ring Group Extension” created in the Epygi
(e.g. Extn 400).
•Click on Apply.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 16 31-Mar-16
6. At this point the door station should be registered to the Epygi. A test call can be made from the door station to any
extension in the Epygi by dialing “*”, followed by the extension number (e.g. “*,00” to reach the Auto Attendant). To
disconnect, press “#”. From within the Epygi the registration status can be verified by going to Status, System Status, IP
Lines Registration.
7. Optional door relay operation.
•User Switch Codes Switch 1 – Enter in the name of the activation code that will be used to operate the switch (e.g. 22). If
connected to a door strike a user can operate the door station relay by pressing the User Switch Code followed by “*” (e.g.
dial “22*”).
•Click on Apply.
Configuring Leviton OmniTouch 7 Touchscreen
Configure the OmniTouch 7 Touchscreens from the Dealer PC Access management system.
The Leviton OmniTouch 7 Touchscreen will need to be configured from the PC Access management software.
CRITICAL NOTE: before performing any of the following steps, use the “Check for Updates” feature in PC Access to obtain and
install the latest updates for PC Access, the automation controller being used, and the OmniTouch 7 Touchscreens. Failure to have
all items properly updated will lead to unsatisfactory results.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 17 31-Mar-16
1. Open the controller’s PC Access file.
2. Click on Extended Setup and enter the following:
•SIP Server Address – enter in the IP Address assigned to the Epygi.
•SIP Server Port – this is the SIP port configured in the Epygi (5060 is the default)
•SIP Page Group – this is the number created in the Epygi to page a group of extensions (e.g. extn 401).
3. Click on OmniTouch 7 Screens and enter the following for each OmniTouch 7 (Note: only the fields required for door
station integration are discussed here):
•ID – enter in the desired ID for each touchscreen installed.
•SIP Username – this is the SIP Registration Username assigned to the OmniTouch 7 in the Epygi IP Line Settings.
•SIP Password - this is the SIP Registration Password assigned to the OmniTouch 7 in the Epygi IP Line Settings.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 18 31-Mar-16
4. Click on Sip Stations and add the following information for each SIP device (door station) that is not a touchscreen:
•To add a SIP Station, click on the green “+” in the icon bar.
•SIP Station Name – this will be a name that will be displayed on the Touchscreen 7 for calling to the SIP device (e.g. Door
Station1).
•Station Type – select the type of device (e.g. Helios 2N).
•Station Address – enter the IP Address for the Door Station (e.g 2N). Entering the door station IP will allow for video of the
person to be previewed when receiving calls. The preview is available prior to answer.
•SIP User – enter the extension number in the Epygi that will be called when pressing the intercom button from the
Touchscreen. Typically this will be the extension for the Ring Group.
•Activate Switch – identifies the switch to be activated in the door station for operating the door relay (e.g. switch 1 in the 2N
will activate the door relay, ONLY applicable when calling to the 2N door station).

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 19 31-Mar-16
5. Once all of the above fields have been completed, perform the following steps
•Select Communication from the top menu, and select Write to the controller.
•After the above process is finished select Restart Touchscreens from the Communication drop down.
Update the OmniTouch 7 Touchscreen
1. At each OmniTouch 7 Touchscreen installed, go into the internal Setup Configuration and set the Touchscreen ID to match
the value set in the PC Access file. The Setup Configuration can be accessed by touching the OmniTouch 7 screen while the
unit is booting up, and after the Leviton logo is displayed. It can also be accessed from the main screen by pressing Settings.
From the Settings screen press and hold the Settings option in the bottom right corner. This may require several attempts.
2. Press the SAVE & EXIT button.
3. After rebooting, test the system.
4. Note: Anytime any changes are made to the settings described in the PC Access Configuration above, it is imperative that
all of the OmniTouch 7 Touchscreens be rebooted.
Call Scenarios
Call handling from the OmniTouch 7 Touchpad
Originating a call from OmniTouch 7 to the 2N Helios Door Station
1. From the home display screen on the OmniTouch 7, press Intercom.

Configuring Leviton OmniTouch 7 Touchscreens & Helios 2N door stations with the Epygi
QX IP PBX
Revision 1.0 20 31-Mar-16
2. To dial one of the SIP stations press the device name (e.g. QX200).