Equinox Systems BLITZER User manual

Order code: STRO02
User manual
www.prolight.co.uk

WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE YOUR INITIAL START-UP!
CAUTION!
Keep this equipment away from rain,
moisture and liquids.
SAFETY INSTRUCTIONS
Every person involved with the installation, operation & maintenance of this
equipment should:
- Be competent
- Follow the instructions of this manual
CAUTION! TAKE CARE USING THIS EQUIPMENT!
HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!
Before your initial start-up, please make sure that there is no damage caused during
transportation. Should there be any, consult your dealer and do not use the
equipment.
To maintain the equipment in good working condition and to ensure safe operation, it is necessary
for the user to follow the safety instructions and warning notes written in this manual.
Please note that damages caused by user modications to this equipment are not
subject to warranty.
Equinox Blitzer Strobe Safety

Equinox Blitzer Strobe Safety
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the
non-observance of this manual or any unauthorised modication to the equipment.
• Never let the power-cable come into contact with other cables. Handle the power-cable
and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not connect this equipment to a dimmer-pack.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
• Do not expose to ammable sources, liquids or gases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the
power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment and
the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power supply immediately.
Have a qualied engineer inspect the equipment before operating again.
• If the equipment has been exposed to drastic temperature uctuation (e.g. after
transportation), do not switch it on immediately. The arising condensation might damage
the equipment. Leave the equipment switched off until it has reached room temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Prolight dealer
for service.
• Only use fuses of same type and rating.
• Repairs, servicing and power connection must only be carried out by a qualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.

You should nd inside the Equinox carton the following items:
1, Equinox Blitzer Strobe 2, Instruction manual
Technical Specications:
DMX channels: 2
Voltage: AC 110-240V - 50-60Hz
Fuse: F1A-250V
Power consumption: 23W
Dimensions: 330 x 235 x 210mm
Weight: 2.1Kgs
Operations:
There are 4 operating modes to choose from:
1, Manual 2, Sound Active 3, DMX 4, Master/slave
Manual Mode
To run the Blitzer Strobe in Manual mode, press the ‘MODE” button to show “F--” on the LED display.
Now to set the ash rate, use the “UP” and “DOWN” buttons and adjust the speed from 0-9. To set the
intensity press the “MODE” button to show “C--” on the LED display and use the “UP” and “DOWN”
buttons to adjust the brightness from 0-9.
Flash Rate: 0 = Slow, 9 = Fast
Intensity Levels: 0 = Off, 9 = Full on
Sound active Mode
To run the Blitzer Strobe in Sound active mode, press the ‘MODE” button to show “S--” on the LED
display. To set the sensitivity level, use the “UP” and “DOWN” buttons and adjust the sensitivity from
0-9.
Sensitivity Levels: 0 = Low, 9 = High
DMX Mode
To run the Blitzer Strobe in DMX mode, press the ‘MODE” button to show “Add” on the LED
display. Now use the “UP” and “DOWN” buttons to set the DMX address from 001 - 512.
Analogue controller connection
The Blitzer Strobe features 2 1/4” jack sockets (in/out) for analogue remote operation and allows for
several Blitzer Strobes to be linked together via using jack cable/s.
Control of the strobes is possible via analogue 10V signals.
TIP = +10V, Sleeve = Ground
To control the strobe/s via a analogue remote, you must set the strobe/s DMX address to 001.
Master/slave mode
Link the units together using a 3-pin XLR DMX cable, then press the “MODE” button to select one of the
above modes for the master unit. On the Slave unit/s press the “MODE” button to show “Add” on the
LED display. Now use the “UP” and “DOWN” buttons to set the DMX address to 001. The Slave unit/s
will then follow in sequence with the Master unit.
Equinox Blitzer Strobe Technical specications

Further DMX cables can be purchased from
all good sound and lighting suppliers or
Prolight dealers.
Please quote:
CABL10 – 2M
CABL11 – 5M
CABL12 – 10M
DMX Chart
Over view
Main features
• Single 50W LED • Large coverage area
• Adjustable ash and intensity rate • Flash rate range of 1 - 12 Fps
• Adjustable hanging bracket
DMX-512:
• DMX (Digital Multiplex) is a universal protocol used as a form of communication between
intelligent xtures and controllers. A DMX controller sends DMX data instructions form the
controller to the xture. DMX data is sent as serial data that travels from xture to xture via the DATA
“IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have a data “out”
terminal).
DATA Cable (DMX cable) requirements (for DMX operation):
• The Equinox Blitzer Strobe can be controlled via DMX-512 protocol. The DMX address is set on the
back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for data
input/output (gure 1).
Figure 1
Also remember that DMX cable must be daisy chained and cannot be split.
Equinox Blitzer Strobe Overview
MODE
FUSE
IN OUT
ANALOGUE REMOTE
DMX OUTDMX IN
F1A~250V
DOWN
110-240V AC
UP

Notice:
• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield
conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing.
Grounding the shield could cause a short circuit and erratic behaviour.
Special Note: Line termination:
• When longer runs of cable are used, you may need to use a terminator on the last unit to
avoid erratic behaviour.
Using a cable terminator (part number CABL90) will decrease the possibilities of
erratic behaviour.
5-Pin XLR DMX Connectors:
• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin
XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin
XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the
correct cable conversion.
Termination reduces signal transmission problems
and interferance. it is always advisable to connect a
DMX terminal, (resistance 120 Ohm 1/4 W) between
pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.
Equinox Blitzer Strobe DMX Set up

www.prolight.co.uk