ErGear EGDS9 User manual
Model: EGDS9
Monitors Desk Mount Instruction Manual
V2.0
Thank you for choosing this ErGear product! At ErGear we strive
to provide you with the best quality products and services in the
industry. Should you have any issues, please don't hesitate to
Check the VESA Pattern of Your Monitor beforeYouBegin the Installation
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it
is strictly prohibited to dismantle without professionals. Please return to the manufacturer
or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.
IMPORTANT SAFETY INFORMATION
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
Weight Restrictions
2.2-26.4 lbs.
(1-12 kg)
If your monitor weighs
more, this mount is
NOT compatible.
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
100 mm ≈ 4 in.
75 mm ≈ 3 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
01 02 03 04 05 06 07 08 09 1110
Product Features
C-Clamp
Mounting
Grommet
Mounting
01 02 03 04 05 06 07 08 09 1110
Warning!
Do not adjust tension without monitor.
1. Ensure monitor has been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensure the net weight of monitor (including accessories) is between
2.2~26.4 Ibs (1-12 kg).
Clockwise to reduce
tension(carry less weight) Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign
01 02 03 04 05 06 07 08 09 1110
5/32 in.(4mm)
Medium Allen Key
M (x1)
Base
A (x1) Grommet Plate
E (x1)
1/8 in.(3mm)
Small Allen Key
L (x1)
Arm
C (x2)
Arm Extension
B (x2)
Bottom Pad
G (x1)
Bolt
K (x4)
C-Clamp
J (x1)
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Warning:This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use
damaged or defective parts. lf you require replacement parts, contact our
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Supplied Hardware for Step 4
13/64 in.(6mm)
Large Allen Key
N (x1)
13/64 in.(6mm)
Large Allen Key
N (x1)
C-Clamp Brace
I (x1)
Bottom Plate
F (x1) Decorative Cover
H (x1)
Phillips Screwdriver Drill Wood Drill
10-15mm (25/64 in.-19/32 in.)
Bolt
M4x12mm
F1 (x8)
Bolt
M4x16mm
F2 (x8) 5mm Spacer
F3 (x8)
Monitor Plate
D (x2) D5 Washer
F4 (x8)
01 02 03 04 05 06 07 08 09 1110
1. Install the Base
Warning:
Ensure bolts are
secured firmly.
A. For Clamp Mounting
1 31/32 in.-3 11/32 in.
50-85mm
19/32 in.-2 9/32 in.
15-58mm
K
I
A
M (Medium Allen Key)
(G)
G
15/64 in.(6mm)
M (Medium Allen Key)
JE
M
OR
01 02 03 04 05 06 07 08 09 1110
N (Large Allen Key)
Warning:
Ensure bolts are
secured firmly.
B. For Grommet Mounting
H
K
F
M (Medium Allen Key)
(G)
G
J
N (Large Allen Key) N (Large Allen Key)
E
10-15mm
25/64 in.-19/32 in.
10-15mm
25/64 in.-19/32 in.
01 02 03 04 05 06 07 08 09 1110
2. Install the Arms and Arm Extensions to Base
B
C
L (Small Allen Key)
L (Small Allen Key)L (Small Allen Key)
±135°±135°
±135°
±135°
01 02 03 04 05 06 07 08 09 1110
For Monitor with Curved or Recessed Back
For Monitor with Flat Back
Phillips
Screwdriver
[not included]
D
F1
F4
D
F2
F4
F3
3. Attach Monitors to the Arms
HEAVY! You may need
assistance with this step.
Note: If needed, pull the lock
plate back and lift the TV to
seperate the TV from the arm.
1
2
01 02 03 04 05 06 07 08 09 1110
4. Adjust Gas Spring Tension
Be sure to keep the arm in
horizontal position during
adjustment. Or else, it
would be difficult to adjust
the mount or damage the
mount.
1. If the monitor can stay at the desired height by itself,
no adjustment needed.
2. If the monitor rises up, press the arm to keep it in
horizontal position and then use the Large Allen Key (N)
to turn the bolt clockwise(“-” direction) to reduce
tension of the arm only until the monitor can stay at the
desired height by itself.
3. If the monitor falls down, lift the arm to keep it in
horizontal position and then use the Large Allen Key (N)
to turn the bolt counter-clockwise(“+” direction) to
increase tension of the arm only until the monitor can
stay at the desired height by itself.
+
-
N (Large
Allen Key)
Desk
+
+
01 02 03 04 05 06 07 08 09 1110
6. Rotation Adjustment
Rotation
This function works better for
monitors with the center of
gravity.
5. Tilt Adjustment
N (Large Allen Key)
T
1. Slightly loosen two preassembled bolts [T].
2. Adjust TV to your desired tilt angle.
3. Retighten both bolts [T] to secure the TV in place.
180°
01 02 03 04 05 06 07 08 09 1110
7. Route Cables along the Arms
Phillips
Screwdriver
[not included]
①
②
①
②
①
①
②
②
01 02 03 04 05 06 07 08 09 1110
Other manuals for EGDS9
1
Table of contents
