Forging Mount HY9440 User manual

WARNING:This product
contains small items that could
be a choking hazard if swallowed.
Before starting assembly, verify
all parts are included and
undamaged. If any parts are
missing or damaged, do not return
the damaged item to your dealer;
contact Customer Service.
Never use damaged parts!
NOTE: Not all parts and hardware
included will be used.
Tools Needed
Hardware Included
Lag Screw
Ax4
Wall Anchor
Cx4
Lag Screw
Washers
Bx4
99lbs
(45kg)
Does your TV (including accessories)
weigth more than 99 lbs. ( 45 kg ) ?
No — Perfect!
Yes — This mount is NOT compatible.
What is your wall made of ?
Dry wall with
woodstuds ?
Solid concrete or
concrete block?
Perfect!
Please read throuth these instructions completely to be sure you're comfortable with
this install process. Also check your TV owner's manual to see if there are any special
requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation,
assembly or use of this product,please contact US via: [email protected]
Getting Started
WARNING: Exceeding the weight
capacity can result in serious personal
injury or damage to equipment! It is the
installers’s responsibility to make sure the
weight of the TV (with accessories) does
not exceed 99 lbs(45kg).
CAUTION: Avoid potential personal injuries and property damage!
This product is designed for use in wood stud/concrete walls DO NOT install into drywall.
The wall must be capable of supportingfive times the weight of the TV and mount combined.
Do not use this product for any purpose not explicitly specified by manufacturer.
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
TV Washers
J
Ø5 x4 Ø8 x4
Wood Staud Install
AwlStud Finder
7/32in.
(5mm)
Wood
Drill Bit Hammer
Concrete Install
3/8in.
(10mm)
Concrete
Drill Bit
Tape
Measure Pencil Screwdriver
Electric
Drill
1/2 in (13 mm)
Socket Wrench 03 x4
Arm Extension
04 x2
Fixed Bracket
Velcro Tie
08 x5
TV Bracket
05 x2
M6
M4 M8
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter ( M4, M6, or M8 ) to use.
Step 1-1 Select TV Screw Diameter
Step 1-2 Select TV Screw Length
CAUTION: Verify
adequate thread engagement
with the screw/washer/spacer
combination and TV bracket.
-Too short will not hold the TV.
-Too long will damage the TV.
FLAT BACK
Too Short
Too Long
Correct
ROUND BACK INSET HOLES CABLES
If your TV has a flat back, AND you want your TV closer
to the wall, use the shorter screws(A).
Use the spacers and longer screws(B) to accommodate:
· Round/irregular back TVs
· TVs with inset mounting holes
· Extra space needed for cables
Standard configurations
are shown. For special
applications, or if you
are uncertain about your
hardware selection,
you can contact at:
[email protected]
(a1) Flat Back
STEP1-3 Secure the TV Mount Plate / TV Brackets to the back of TV
D/F/H
J
D/F/H
J
(a2) Flat Back
Alternate Spacer SetupsAlternate Spacer Setups
05
0502
Position your TV Mount Plate / TV Backets over your TV hole
pattern- making sure the brackets are centered and level over
the TV hole pattern.Secure the TV plate or brackets using your
screw/washer spacer selectiion:
(a) for Flat Back
(b) for Round Back/Extra space
5/16x2.75”
TV Screws
M6X15mm
Fx4
M6X35mm
Gx4
Xx4Hx4
M8X15mm
Dx4 Ex4
M4X12mm M4X30mm
M8X50mm
Ix4
M8X30mm
TV Spacers
L 5mm
Kx8
L 10mm
Lx8
Level
07 x1
Wall Plate Template
06 x1
Instruction Manual V2.0
E/G/I/X
J
K/L
(b1) Round Back / Extra Space (b2) Round Back / Extra Space
E/G/I/X
J
K/L
www.forgingmount.com
Max. VESA: 600X400mm
Max. Distance: 33” (83.8cm)
Model: HY9440
FULL MOTION
TV WALL MOUNT
01 x1
Arm Assembly/ Wall Plate
02 x1
TV Mount Plate
Drillin g Template
UP
Px1
WrenchBolts
M5X12mm
Mx2
Washers
Ø5
Nx2
Ox1
Allen key
CAUTION: Ensure TV Mount Plate / TV Bracket is
securely fastened before moving on to the next step.
Note: If your TV VESA is less than 100x200mm / 4x8 inch,
you only need to install a TV Mount Plte. If your TV VESA is
more than 100x200mm/4x8 inch or less than 600x400 mm /
23x16 inch, you need to install a TV bracket.
02

1.Loosen the pre-assembled bolts of the fixing
bracket .
2.Secure the fixed bracket and Arm Extension to the
TV Mount Plate .
3.Hang the front support onto the arm assembly, and
tighten the bolts and
washers to secure
the TV to the arm assembly.
1. Slightly loosen the bolt or nut with
a wrench .
2. Adjust TV to your desired level and tilt angle.
3. Retighten the bolt or nut to secure
the TV in place.
07 07
06
3 in. (75mm)
B
A
2A-1 2A-2Step 2A Wall Plate Instal (Wood Stud) 2A-3 2A-4
2B-1 2B-2 2B-3 2B-4
Step 2B Wall Plate Instal (Solid Concrete or Concrete Block)
1.Remove the screws and hang the TV onto the arm assembly .
2.Press the safety locks down, then fasten the removed screw .
S2
Step 3A Hang the TV onto the Arm Assembly
（For VESA 100x200 below TVs）
Step 4 Tilt and level adjustment
Made in China
S1
S1
O
04
Step 3B Secure the Fixed Bracket and Arm Extension to the Arm Assemble/Wall Plate,
and Hang the TV to Arm Extension (for large size TVs）
M
M N1
P
N1
Drywall covering the wall must not exceed
5/8 in.(16mm)
Minimum wood stud size: common 2x4 in.
(51x102mm) nominal 1x3 in.(38x8omm)
Locate your studs. Verify and mark the center of
the studs by finding the stud edges using an awl,
a thin nail, or an edge-to-edge stud finder.
Install wall plate using lag screws and
washers . Tighten the lag screws only until
they are pulled firmly a gainst the wall plate .
Drill 3 pilot holes using a 7/32 in (5.5mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth
of 2.36 in.(60mm). Be sure to drill into the center of the stud.
01
06
01
A
B
CAUTION: Avoid potential personal injury
or property damage! All Lag Screws
MUST BE firmly tightened to prevent
unwanted movement of the Wall Plate .
CAUTION: Ensure the Wall Plate is
securely fastened to the wall before
continuing on to the next step.
A
01
01 Position the Wall Plate Template at your
desired height and line up the holes with your
stud center line. Level the wall plate and mark
the holes.
Min. 8 in.
(203mm)
Min. 8 in.
(203mm)
Min. 16 in.
(406mm)
CAUTION: Avoid potential personal injuries and property
damage!
Minimum solid concrete thickness: 8 in.(203mm)
Minimum concrete block size: 8 x 8 x 16 in.(203x203x406mm)
Minimum horizontal space between fasteners: 16 in.(406mm)
Mount wall plate directly onto the concrete surface.
01
Drill four pilot holes using a 3/8 in.
(10 mm) masonry drill bit.
IMPORTANT: Pilot holes must be
drilled to a depth of 2.56 in. (65 mm).
Never drill into the mortar between blocks.
Insert four wall anchors
(10x50mm) to the wall
CAUTION: Be sure the anchors are
seated flush with the concrete surface.
C
Install arm assembly / wall plate
with four lag screws and washers
CAUTION: Improper use could reduce
the holding power of lag screws
DO NOT over-tighten the screws.
01
BA
A
Position Wall Plate Template
at your desired height. Level then
mark the four hole locations.
06
04
02
S1
S2
S2
Tighten the Bolts and
washers to secure
the TV to the arm assembly.
N
M
M
N
01
C
AB
01
07
06
I
M
N
±3°
±10°
Level
M
P
Tilt
N1
P
04
02
03
O