Ergotron Zip40 User manual

1 of 7
888-06-011-G-00 rev. B • 03/20
Zip40 Cart, Replace Outlet Box
7mm
Service Manual
Tools Needed
There is one outlet box that is
inverted. make sure your new
outlet box matches the outlet
box you want to replace.
To prevent equipment damage, discharge body static before handling
the printed circuit boards or any module containing a printed
circuit board. To discharge body static, use a conductive wrist strap
attached to a good earth ground or discharge body static by touching
a grounded bare metal surface. Handle printed circuit boards or
modules by their edges once removed from protective antistatic bags.
ATTENTION
OBSERVE PRECAUTIONS
ELECTROSTATIC
SENSITIVE DEVICES
827-181-00
This product uses semiconductors that can be damaged by electrostatic discharge (ESD).
Always handle with care to avoid damage to electrostatic-sensitive components.
ABC
1
Components
1x 10x
M4
8x
M3 x 4mm

2 of 7
888-06-011-G-00 rev. B • 03/20
WARNING
828-196
Unplug power cord.
DO NOT place hands on or near fans.
Placing hands on or near fans may
cause equipment damage and/or
serious personal injury.
MOVING PARTS
CAN CRUSH AND CUT
These symbols alert users of a safety condi-
tion that demands attention.All users should
be able to recognize and understand the
significance of the following Safety Hazards
if encountered on the product or within the
documentation. Children who are not able
to recognize and respond appropriately to
SafetyAlerts should not use this product with-
out adult supervision!
Hazard Symbols
Review Symbol Signal Word Level of Hazard
NOTE A NOTE indicates important information that helps you
make better use of this product.
CAUTION
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
WARNINGA WARNING indicates either potential for property dam-
age, personal injury, or death.
ELECTRICAL
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
Safety
Warning: Unplug power cable from outlet and make sure power button is turned o before removing side cover. Removing side
cover with power on may cause equipment damage and/or serious personal injury.
WARNING: MOVING PARTS CAN CRUSH AND CUT. Unplug power cord. DO NOT place
hands on or near fans. Placing hands on or near fans may cause equipment damage and/or
serious personal injury.

3 of 7
888-06-011-G-00 rev. B • 03/20
1Open doors.
2
ab c
Remove back panel.

4 of 7
888-06-011-G-00 rev. B • 03/20
4Unplug power cables from outlet box to be replaced.
3
WARNING
828-196
Unplug power cord.
DO NOT place hands on or near fans.
Placing hands on or near fans may
cause equipment damage and/or
serious personal injury.
MOVING PARTS
CAN CRUSH AND CUT
Unplug power cable from cart and remove side cover.

5 of 7
888-06-011-G-00 rev. B • 03/20
5
6
Remove Controller Box:
a. Unplug cables from controller box.
b. Unscrew 10 nuts to remove controller box.
c. Unplug outlet box you are replacing.
a. Unscrew the 8 screws and remove outlet box.
b. Attach new outlet box and secure with 8 M3 x 4mm screws.
a
a
b
b
c
7mm
8x
M3 x 4mm

6 of 7
888-06-011-G-00 rev. B • 03/20
8Plug power cables back into outlet box.
7Replace Controller Box:
a. Connect to appropriate controller box cable to outlet box.
b. Attach controller box with 10 M4 nuts.
c. Plug cables into controller box.
ab c
7mm
10x
M4

7 of 7
888-06-011-G-00 rev. B • 03/20
9
ab
Attach side cover.
10
abc
Attach back panel.
k(UJRWURQ,QF$OOULJKWVUHVHUYHG
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
)RUORFDOFXVWRPHUFDUHSKRQHQXPEHUVYLVLWKWWSFRQWDFWHUJRWURQFRP
)RU6HUYLFHYLVLWZZZHUJRWURQFRP
)RU:DUUDQW\YLVLWZZZHUJRWURQFRPZDUUDQW\