Ergotron Neo-Flex User manual

1 of 19
888-24-075-W-01 rev. M • 01/19
www.ergotron.com | USA: 1-800-888-8458 | Europe: [phone] | China: 400-120-3051 | Japan: [email protected]
English, Español, Français, Deutsch, Nederlands, Italiano, Svenska, 日本語, 汉语
Neo-Flex™ WideView Workspace
Användarhandbok
Svenska
För den senaste Installationshandboken se: www.ergotron.com

2 of 19
888-24-075-W-01 rev. M • 01/19
WARNING
DO NOT load Cart below minimum or above
maximum weight capacities. DO NOT mount a
display larger than the recommended size.
Failure to comply with warning may result in
Cart instability leading to equipment damage or
personal injury.
Min. 11 lbs (5 kg)
Max. 46 lbs (20.9 kg)
Min. 14 lbs (6.35 kg)
Max. 49 lbs (22.2 kg)
WARNING
Impact Hazard!
Moving Parts can Crush and Cut.
Minimize Lift Tension BEFORE
Removing Mounted Equipment.
To Minimize Lift Tension
1. Lower worksurface to lowest position.
2. Turn adjustment nut at top of riser
counterclockwise until it stops (may require
40-60 turns to minimize lift tension).
3. After removing or adding equipment adjust
lift tension to compensate for weight
of new load.
Failure to heed this warning may result in
serious personal injury or property damage!
14mm
9/16”

WARNING
A primary mechanism within the Cart
is under tension and can be
hazardous to people exposed to it
under certain conditions.
DO NOT open the Cart tower or base.
DO NOT attempt to service the Cart.
DO NOT remove safety guards or
labels designed to protect or inform
of possible hazards.
Only Ergotron-approved installers
may service or otherwise modify
Cart. Failure to heed this Warning
may result in serious Personal Injury
and Damage both to the cart and
equipment.
STORED ENERGY HAZARD!
DO NOT OPEN TOWER OR BASE.
DO NO REMOVE SAFETY GUARD.
240-027-00
TIPPING HAZARD!
DO NOT allow children to climb on Cart.
DO NOT route electric cords or equipment
cables within reach of children.
LOCK CASTERS when Cart is stationary.
DO NOT move Cart with Display in highest
position.
DO NOT move Cart over cords or uneven, dirty,
soft or sloping surfaces.
DO NOT move Cart by pushing on Display.
Failure to comply with this warning may result
in Cart instability leading to equipment
damage or personal injury.
WARNING
TO MOVE CART
1. Push Display down to lowest position.
2. Disconnect power cord and secure to Cart.
3.
Unlock casters; point casters in direction of travel.
4. Use rear handle to push Cart.
SafetySäkerhet

3 of 19
888-24-075-W-01 rev. M • 01/19
12"-18"
(305-457 mm)
3"- 8.5"
(76-216 mm)
<40 lbs. ( 18.1 kg)
20"
(50.8 cm)
20"
(50.8 cm)
16 - 30 lbs
(7.3 - 13.6 kg)
20˚*
10˚*
90˚
*±5˚
Stand
Sit
Funktioner och specifikationer
VARNING: ÖVERSKRID INTE
MAXVIKTKAPACITETEN. DU
KAN ORSAKA ALLVARLIG PER-
SON ELLER EGENDOMSSKADA
CPU Holder
Stand
Sit
Viktigt! Efter avslutad installation måste du justera produkten. Se till att all utrustning är installerad
korrekt innan du påbörjar justeringen. Du ska lätt kunna flytta produkten över hela rörelseområdet och
den ska stanna i den position du lämnar den. Om det är för lätt eller trögt att ändra positioner eller om
produkten inte stannar i avsedd position, följ justeringsinstruktionerna för optimal positionsrörlighet. Det
kan ta mer än en justering för att nå önskat beteernde beroende på produkt och justering. Om du lägger
till eller tar bort utrustning bör du jutera produkten för den nya viktbelastningen. På så sätt bibehåller du
en säker och behaglig arbetssitation.

4 of 19
888-24-075-W-01 rev. M • 01/19
AB C D E F
1
2
3
4
5
6
7
8
9
14mm (9/16")
19mm
(3/4")
>9" (229 mm)
8mm
(5/16")
1x
M4 x 12mm
4x
3mm
1x 1x
1x
1x 1x
1x
1x
2x 4x
M5 x 18mm
4x
2x
1x
2x
1x
2x
1x
1x 2x
1x
1x
1x 2x 2x
2x
M5 x 10mm
M5 x 8mm
4x
2x
1x 4x 1x
1x
M3 x 6mm
M6 x 14mm
M6x33mm
4x
4x 4x 4x 4x
4x
M5 x 12mm M5 x 20mm
M5 x 7mm M6 x 12mm
CPU Holder
5-sided Security Wrench
Security Screw
Mounting Holes
M8M5 Converter
Komponenter
Verktyg som behövs
CPU Holder
Vite di sicurezza
5-sided Security Wrench
Mounting Holes
M8M5 konverterare

5 of 19
888-24-075-W-01 rev. M • 01/19
2x
3mm
2
cd
efg
ab
1180˚
a
b
cd
19mm
(3/4")
5-sided Security Wrench5-sided Security Wrench
CPU Holder NOTE: If you are not attaching a CPU to your
cart, skip step 2 and proceed to step 3.

6 of 19
888-24-075-W-01 rev. M • 01/19
h
kl
ij
3mm
2x
mn
5-sided Security Wrench
5-sided Security Wrench
Caution: Do Not over tighten fasteners.
NOTE: Position at bottom of tower.
Do not tighten at this time.
Tipping Hazzard: Position bracket so that CPU
attaches as low as possible on the tower.

7 of 19
888-24-075-W-01 rev. M • 01/19
t
s
1x
op
qr
M5 x 18mm
5-sided Security Wrench
5-sided Security Wrench
Vite di sicurezza

8 of 19
888-24-075-W-01 rev. M • 01/19
3a
b
c
2x
1x
Mounting HolesMounting Holes

9 of 19
888-24-075-W-01 rev. M • 01/19
4abcd
e
2x
M5 x 10mm
2x
1x
iiiii
d
i

10 of 19
888-24-075-W-01 rev. M • 01/19
5abc
d
2x
2x
egf
6
2x
>9" (229 mm)
2x
M6x33mm
M6x33mm