Ericsson KRY 101 1613 User manual

ericssonz
Installation Manual
VEHICLE HANDSFREE KIT
KRY 101 1613

2
TABLE OF CONTENTS
Page
GENERAL.....................................3
WIRING TO AN EXTERNAL
ANTENNA...............................4
MOUNTING THE CRADLE............5
WIRING TO THE VEHICLE'S
BATTERY................................6
MOUNTING THE MICROPHONE..7
INSERTING AND REMOVING
THE RADIO.............................8
SPECIFICATIONS.........................9
TROUBLESHOOTING...................10
Copyright © September 1995, Ericsson Inc.
NOTICE!
This manual covers Ericsson and General Electric
products manufactured and sold by Ericsson Inc.
This manual is published by Ericsson Inc., without any warranty.
Improvements and changes to this manual necessitated by
typographical errors, inaccuracies of current information, or
improvements to programs and/or equipment, may be made by
Ericsson Inc., at any time and without notice. Such changes will be
incorporated into new editions of this manual. No part of this manual
may be reproduced or transmitted in any form or by any means,
electronic or mechanical, including photocopying and recording, for
any purpose, without the express written permission of Ericsson Inc.

3
GENERAL
The VEHICLE HANDSFREE KIT
provides for the safe and easy use of the
DPE-100 portable radio in a vehicle.
The VEHICLE HANDSFREE KIT
powers the radio with the vehicle's battery
and provides a microphone and speaker
for handsfree use.
• The kit includes the following
• Handsfree cradle
• Mounting brackets
• Microphone and clip
• Antenna interface cable with TNC
connector
• Cradle power cable
• Fuse kit

4
WIRING TO AN EXTERNAL ANTENNA
An external antenna (to be purchased
separately) greatly improves performance.
The package includes an external
antenna cable, but do not install it unless
the external antenna is installed. When
the external antenna cable is connected,
the radio's internal antenna is bypassed.
NOTE
Take the following steps to install the
antenna cable:
1. Remove the plastic insert from the
antenna connection hole at the top
back of the cradle.
2. Push the long connector on the
antenna cable through the hole.
3. Press the connector into the hole until
it snaps into place and close the
opening of the back of the cradle with
the grommet found on the antenna
cable. Press the antenna cable into
the retainer at the bottom of the
cradle.

5
MOUNTING THE CRADLE
Follow the steps below to attach the
cradle to the swivel mount Locate the
cradle within easy reach of the driver where
it will not obstruct driving.
SWIVEL MOUNT
Place the swivel joint into desired
position and mark the drilling area using
the holes as a template. Be sure to check
the drilling area for hidden obstacles
before drilling. Drill the marked holes for
unlt placement.
1. Place the ball joint against the pocket
mount. Insert the large screw through
the center of the ball joint & pocket

6
mount and loosely attach with the nut
and the back of the pocket mount.
2. Place the unit on the drilled holes and
mount it with the screws provided.
3. Adjust the ball joint to desired position
and tighten the center screw within the
ball joint.
4. Slide the cradle over the angled
guides and push down until the cradle
is secure
WIRING TO THE VEHICLE'S BATTERY
l. Cut a short 6 - 8 inch length of red
wire from the power cable.
2. Use the short length of red wire to
connect one terminal of the fuse
holder to the positive battery terminal
(12 V. battery with negative ground
only).
3. Connect the power cable's red wire to
the other terminal of the fuse holder.
4. Connect the power cable's black wire
to ground and insert the 3 Amp fuse
into its holder.
5. Route the cradle power cable and
push it into the cradle's power jack.

7
MOUNTING THE MICROPHONE
1. Locate the microphone out-of-the-way
about 8-12 inches from the driver's
face and awayfrom windows or other
sources of noise. Use the visor clip or
adhesive strip to mount the
microphone. ALWAYS USE THE
VISOR CLIP IF POSSIBLE. The bulb
on the microphone must be toward
the driver and the mike wire rmust
lead away from the driver. Route the
mike wire away from vehicle parts
that could damage insulation or cut
the wire.
2. Plug the microphone into the black
cylindrical jack at the end of the
cradle cord.

8
Be especially careful not to pull the mike
cable or poke it with installation tools.
NOTE
INSERTING AND REMOVING THE
RADIO
Before inserting the radio. check to
see if the battery is medium, high. or extra
high capacity.
If the battery is medium, fold out the
support before inserting the radio.
INSERTING THE RADIO
1. Find the small grooves on the sides of
the radio at the bottom, and align
them with the guides in the base of
the cradle. Place the radio straight
down into the cradle. The antenna
should rest over the groove at the top
left of the cradle.

9
2. With the base of the radio in place,
gently push the top back into the
cradle until you feel it snap in.
If the battery is high or extra high
capacity, fold in the support.
REMOVING THE RADIO
Gently pull out on the top of the radio
until you feel it loosen, then remove the
phone.
SPECIFICATIONS
• INPUT VOLTAGE 11- 16V.DC/l.7A
• CHARGING TEMPERATURE
RANGE 25°F. to l05°F.

10
TROUBLESHOOTING
RADIO PROBLEM PROBABLE CAUSES SOLUTION
The VEHICLE HANDSFREE
unit does not receive vehicle
power
• cradle is wired to a switchable
power source that is turned off
• fuse is blown
• polarity is reversed at the battery
connection
• if wired to the ignition switch,
ignition may need to be turned on
• check fuse and replace if
necessary
• be sure the red power cable wire
is attached to the positive battery
terminal, black to ground
Radio with low battery does not
work in the cradle radio battery is dead Be sure the radio battery is charged. If not, let it charge in the
cradle for 10 not minutes
Radio works outside the cradle,
but not in it • radio is not properly seated
• system connector contacts dirty
• external antenna cable attached
but antenna is disconnected
• be sure the radio is properly
seated
• clean system connector contacts
• be sure the external antenna is
connected
The other party of the radio
connection cannot hear sound The microphone jack is not inserted into the connection box Clean the microphone plug and insert it into the connection box

11
This page intentionally left blank

Ericsson Inc.
Private Radio Systems
Mountain View Road
Lynchburg, Virginia 24502 AE/LZT 123 1881 R1A
1-800-528-7711 (Outside USA, 804-528-7711) Printed in U.S.A.