ESCALADE Goalrilla B2415 User manual

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
A S S E M B L Y I N S T R U C T I O N S
Contact Escalade® Sports customer service department at:
Phone: 1-888-USA-GOAL Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [email protected]
Please Do Not Return This
Product to the Store!
2017 Escalade Sports
2L-7626-00
MODEL NO.
B2415
L E D
H O O P L I G H T

2
P R E - A S S E M B L Y T I P S
Contact Escalade® Sports customer service department at:
Phone: Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
1-888-USA-GOAL
2017 Escalade Sports
P R E - A S S E M B L Y T I P S
2L-7626-00
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
Please Do Not Return This Product To The Store!
3/8” drive ratchet wrench
9/16” Deepwell socket
2-10mm socket and wrench
2-13mm socket and wrench
Needle nose pliers
6’ Step ladder
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page to identify and sort all fasteners. Check all cartons for kits. 5
All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
6. Tools required for assembly:
Tools Optional:
Cordless Drill
Power Socket Adapter for a 9/16 Deepwell socket

3
!If using a ladder during assembly, use extreme caution.
!2 capable adults are recommended for this operation.
!Assemble the pole sections properly (if applicable). Failure to do so could cause pole sections to
separate during play or transport.
SAFETY INSTRUCTIONS
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this system.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY
DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully.
Check entire box and inside packing material for parts and/or additional instruction material. Before
beginning assembly, read the instructions and identify parts using the hardware identifier and parts list
in this document. Proper and complete assembly, use and supervision is essential for proper operation
and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not
installed, maintained, and operated properly.

4
Notch
LOCK
4A-8243-00
LARGE WHEEL ROLLER
3M-9044-00
BOTTOM BRACKET
8S-7939-00
TOP BRACKET
8S-7938-00
MOUNTING PLATE ASSEMBLY
1A-7938-00
23
7
10B
12
(QTY. 1) (QTY. 1) (QTY. 1)
(QTY. 1)
(QTY. 2)
P A R T S L I S T ( N O T A C T U A L S I Z E )
(QTY. 1)
4
Caution
Decal
1
(QTY. 1)
Caution
Decal
1"X1.5" LIGHT BAR END CAP
3M-9045-00
END HANDLE
3M-9046-00
Light Bar
1A-7939-00
11
(QTY. 1)
LED LIGHT ASSEMBLY WITH CORD
6Q-6009-00
6
(QTY. 1)
9
ROLLER
3M-9043-00
(QTY. 3)
5
Pinch Point!
Watch
Your Hands
CAUTION
Pinch Point!
Watch
Your Hands
CAUTION
8
Notch
*Pre-installed
10A
Stop
Decal
Stop
Decal
(QTY. 1)
TOP POLE
8S-8244-00
(QTY. 1)
BOTTOM POLE
8S-7942-00
CENTER POLES
8S-7943-00
(QTY. 3)
NotchNotch

5
ANGLE INDICATOR
2L-7625-00
H A R D W A R E I D E N T I F I E R ( A C T U A L S I Z E )
U-Bolt For 5x5 Pole (7B-6296-00)
U-Bolt For 6x6 & 5-1/2”X5-1/2” Pole (7B-6297-00) (QTY. 2)
(QTY. 2)
U-Bolt For 6x8 Pole
(7B-6298-00)
(QTY. 2)
BUBBLE LEVEL
2Q-6474-00
1/2"X3.5" PIN
7B-6545-00
M8X90mm
1B-7157-00
(QTY. 4)
M8X20mm
1B-7156-00
(QTY. 6)
M8 WASHER
2B-6797-00
(QTY. 18)
M8 LOCKNUT
2B-6808-00
(QTY. 8)
COTTER PIN
7B-6547-00
(QTY. 4)
(QTY. 1)
(QTY. 1)
(QTY. 1)
13
13
13
14
15
16
17
18
19
21
22
20
23
3/8”
FLAT WASHER
701-50
3/8”-16
NYLON LOCKNUT
901-28
(QTY. 4)
(QTY. 4)
Packed with
instruction manual
4 extra for Goalrilla
Freight Train model
*NOTE: DEPENDING ON YOUR MODEL YOU WILL HAVE EXTRA HARDWARE.

6
M6 LOCKNUT
2B-6142-00
M6 WASHER
2B-6827-00
M8 LOCK NUT WITH CAP
2B-6829-00
CABLE GROMMET
3M-9047-00
M8 X 50mm BOLT
1B-7158-00
M6 X12mm
1B-7160-00
M6 WASHER LARGE
2B-6014-00
M6 X 50mm BOLT
1B-7159-00
H A R D W A R E I D E N T I F I E R ( A C T U A L S I Z E )
(QTY. 1)
(QTY. 4)
(QTY. 2) (QTY. 10)
(QTY. 8) (QTY. 10)
24 25
(QTY. 2)
27 28
29
30 31
(QTY. 4)
M6 LOCK WASHER
2B-6828-00
(QTY. 10)
32
26

7
ŸTo install on a Goalrilla unit please go to www.goalrilla.com/customer-service/product-manuals
and click on “LED Hooplight Goalrilla mounting instructions“.
ŸFor go to and click on “LED Hooplight Goalsetter www.goalsetter.com/content/4/customer-service/
Goalsetter Mounting instructions” under product manuals.
Before installing the LED hoop light determine which basketball system
you have. Depending on your model the mounting locations will vary.
Please refer to your Basketball systems owner’s manual for your Model
number. Alternatively, the Goalrilla basketball models will have a sticker
on the back of the pole with the model number (starts with the letter B).

8
1
13
14
15
HARDWARE NEEDED (ACTUAL SIZE)
ASSEMBLY TIP
The following pages will have a picture of the Hardware Needed
along with the Quantity, Part Number and Description. You can
lay the hardware on the picture to identify the hardware.
14 15
3/8”
FLAT WASHER
701-50
3/8”-16
NYLON LOCKNUT
901-28
(QTY. 4)
(QTY. 4)
TOOLS NEEDED
1. Lower the backboard to the lowest position until the Lower arms touch the safety stop. See Figure 1.
DETAIL A
FIGURE 1
NOTE: Additionally two U-bolts #13 are needed, see
Page 5 to determine which size you need for your pole.
Shorter distance
Safety Stop
NOTE: Lower backboard
until lower arms rest on
the safety stop.
Lower Arm
TOOLS RECOMENDED (OPTIONAL)
NOTE: Attach U-bolts close to the
upper arms but make sure U-bolt
and board arm do not touch.
13
9/16”
Deepwell
Socket 6’ Ladder Cordless Drill Socket Adapter
2. From the front of the pole attach the U-Bolts #13 onto the pole and through the mounting
plate #1. Fasten with Washer #14 and Lock Nuts #15 until the Plate does not slide on the
pole but leave it loose enough to adjust it. See Figure 1 and Detail A.
NOTE: Mounting Plate #1 must be positioned as shown in Detail A.
NOTE: Position the plate as shown. The
studs with the shortest distance to the
end of the plate go at the top.
Longer distance
TOP
NOTE: Make sure your basketball pole is level before mounting the U-bolts #13 and Plate #1.

9
FIGURE 1FIGURE 1
HARDWARE NEEDED
1
3. Center the Mounting Plate #1 on the pole (side to side) and Level it with
the provided magnetic level #16. Place the Level directly on the top studs
as shown in Detail A, and adjust until the plate is level (bubble should
move to the middle of the level). Tighten hardware and verify one more
time that the plate is level before continuing to the next step.
16
BUBBLE LEVEL
2Q-6474-00
(QTY. 1)
16
DETAIL A
TOOLS NEEDED
9/16”
Deepwell
Socket 6’ Ladder

10
3
2
19
22
20
M8X20mm
1B-7156-00
(QTY. 6)
M8 WASHER
2B-6797-00
(QTY. 18)
19 20
HARDWARE NEEDED (ACTUAL SIZE)
M8 LOCKNUT
2B-6808-00
(QTY. 8)
22
M8X20mm
1B-7156-00
(QTY. 2)
M8 WASHER
2B-6797-00
(QTY. 4)
19 20
HARDWARE NEEDED (ACTUAL SIZE)
M8 LOCKNUT
2B-6808-00
(QTY. 2)
22
13mm
TOOLS NEEDED
13mm
Bottom Bracket #3
has 90° angle bend
3
2
TOP VIEW
4. Assemble Top Bracket #2 and bottom Bracket #3 together as
shown. See Figure 1 and Top View.
DETAIL A
FIGURE 1FIGURE 1
19
Before tightening,
be sure these two
surfaces are both flat &
flush with each other.

11
4
17
HARDWARE NEEDED (ACTUAL SIZE)HARDWARE NEEDED (ACTUAL SIZE)
1/2"X3.5" PIN
7B-6545-00
(QTY. 1)
17
5. Place Wheel #4 in top Bracket #2 and insert Pin #17 as shown.
2

12
TOOLS NEEDED
21
21
HARDWARE NEEDED (ACTUAL SIZE)
COTTER PIN
7B-6547-00
(QTY. 1)
21
17
17
Bend
21
17
DETAIL A
DETAIL B
DETAIL C
6. Insert Cotter Pin #21 into Pin #17. See Detail A.
7. Bend both prongs on Cotter Pin #21 until pin is secure. See
Detail B & Detail C.
21
17

13
17
5
HARDWARE NEEDED (ACTUAL SIZE)HARDWARE NEEDED (ACTUAL SIZE)
1/2"X4" PIN
7B-6545-00
(QTY. 3)
17
8. Place Rollers #5 in Brackets and insert Pins #17 as shown.
5

14
21
21
17
Bend
21
17
TOOLS NEEDED HARDWARE NEEDED (ACTUAL SIZE)
COTTER PIN
7B-6547-00
(QTY. 3)
21
DETAIL A
DETAIL B
DETAIL C
9. Insert Cotter Pin #21 into Pin #17. See Detail A.
10. Bend both prongs on Cotter Pin #21 until pin is secure.
See Detail B & Detail C.

15
6
Lip goes to the
outside as shown.
NOTE:
22
20
20
18
M8 WASHER
2B-6797-00
(QTY. 2)
20
HARDWARE NEEDED (ACTUAL SIZE)
M8 LOCKNUT
2B-6808-00
(QTY. 1)
22
HEX HEAD BOLT M8 X 90mm
1B-7157-00
(QTY. 1)
18
13mm
TOOLS NEEDED
13mm
DETAIL A
NOTE
DO NOT over-tighten hardware, Lock
must be able to pivot freely.
11. Insert Lock #6 in Bracket #3 and attach
with hardware as shown in Detail A.
Lip goes to the
outside as shown.
NOTE:
3
3
DO NOT
over-tighten. Lock #6 must
pivot freely

16
20
22
M8 WASHER
2B-6797-00
(QTY. 4)
20
HARDWARE NEEDED (ACTUAL SIZE)
M8 LOCKNUT
2B-6808-00
(QTY. 4)
22
13mm
TOOLS NEEDED
13mm
DETAIL A
12. Attach Bracket assembly to the Mounting
plate as shown in Detail A. Tighten Nuts
#22 in this step.
Wheel at
the top

17
13mm,
10mm
TOOLS NEEDED
13mm,
10mm
24
25
22
27
20
HARDWARE NEEDED (ACTUAL SIZE)
M8X50mm BOLT
1B-7158-00
(QTY. 1)
24
M8 WASHER
2B-6797-00
(QTY. 2)
20
M6 X 50mm BOLT
1B-7159-00
(QTY. 4)
25
M6 WASHER LARGE
2B-6014-00
(QTY. 8)
27
31
M8 LOCKNUT
2B-6808-00
(QTY. 1)
22
M6 LOCKNUT
2B-6142-00
31
(QTY. 4)
JUNCTION BOX
Do this step FIRST!
WIRE
NOTCH
AT THE
BOTTOM
13. Attach Junction box to light bar FIRST. Tighten Bolt
and Nut securely. See Detail A.
LIGHT BAR
LINE UP BEFORE
TIGHTENING
LINE UP BEFORE
TIGHTENING
14. Attach LED lights to light bar #8 with hardware shown,
but do not tighten until the light bar and light brackets are
lined up. Once lined up tighten Nut #31 and Bolts #25.
DETAIL A
SIDE VIEW
JUNCTION
BOX
LIGHT
BAR
NOTCH
8
27
31
27
25
27
27
31
25
27
CORD ON
THIS SIDE
20
NOTE: Raise both light brackets as shown.
NOTE:
Tighten hardware but DO NOT
over-tighten and crush tubes.
CORD ON
THIS SIDE

18
10mm
TOOLS NEEDED
10mm
15. Align the Angle Indicator #23 to the light bracket to match
the angle. Use the side that says “For 5 Pole sections” as
shown in the picture below. When the bracket and the
angle indicator line up tighten angle adjustment bolts,
this will secure the light with the correct angle position.
ANGLE
INDICATOR
For initial installations it is recommended to set the angle to “5
poles sections”. In the event that you want your light closer to the
backboard you can take out one center pole section 10B (will be
shown in later steps).
ASSEMBLY TIP
23
ANGLE ADJUSTMENT
BOLT
LIGHT BRACKET
(TO SCALE)
2L-7625-00
ANGLE INDICATOR
(QTY. 1)
23
NOTE: Angle indicator #23 is
packed with these instructions.
In the event that it is lost, cut
the one above out and use it as
a template.

19
NOTE:
10B
Risk of electric shock!
Replace damaged cord or plug
immediately. If you damage or notice any
cut on the cord during any step in the
assembly, DO NOT continue assembly
until wire is replaced. This product will
conduct electricity!
DANGER
DETAIL B
PINCH POINT!
Watch your
hands when
inserting pole
into roller
assemblies!
CAUTION
A
B
TOOLS NEEDED
6’ Ladder
10B
Top Pole
Top Pole
6
DETAIL A
16. Pull back on the Lock #6 and insert Pole #10B through Rollers on bottom bracket and the Wheel
on Upper Bracket as shown in Detail A. When in the location shown, let go of the lock break #6
and the pole will stay in place. Do not place the pole too high, the power cord still needs to go in it.
17. Have a second person hand you the power cord, then Insert it into Pole #10B until it comes out
the other end. You may have to rotate the head of the connector plug so it fits into the tube.
Stop sticker
at the top.
THE FOLLOWING STEPS REQUIRE 2 PEOPLE.
Lock
RISK OF ELECTRIC SHOCK!
Replace damaged cord or plug
immediately. If you damage or notice
any cut on the cord during any step in
the assembly, DO NOT continue
assembly until Wire is replaced. This
product will conduct electricity!
You may have to gently
rotate head of connector so
it fits in the tube, carefully
guide the cord side to side
past the nuts in the tube.
Cord plug will fit through.

20
HARDWARE NEEDED (ACTUAL SIZE)
CABLE GROMMET
3M-9047-00
(QTY. 1)
29
29
18. Install Cable Grommet #29 on Power cord and slide close to the location
shown. Don't let it slide down the cord too far it will need to be close to this
location for the next step.
Cable Grommet #29 will be stiff but it
will fit on the Power cord. Do not use
any tools that could break the Grommet.
NOTE: