ESCALADE Prince EVOLUTION User manual

MODEL NO.
T8860
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
A S S E M B L Y I N S T R U C T I O N S
Contact Escalade® Sports customer service department at:
Phone: [phone] Toll-Free!
Fax: [phone] Toll-Free!
E-mail: [email protected]
Please Do Not Return This
Product to the Store!
2L-4240-01
2015 Escalade Sports
Ó
“ E V O L U T I O N ”
T A B L E T E N N I S T A B L E

Prince (tm) is a trademark of Prince Sports, LLC.
© 2015 Prince Sports, LLC.
www.princetennis.com
P R E - A S S E M B L Y T I P S
Contact Escalade® Sports customer service department at:
Phone: Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please Do Not Return This Product To The Store!
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
1-866-873-3528
2L-4240-01
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering
parts.
3. To make assembly easier, use the Hardware Identifier on page 3 to identify and sort all fasteners. Check all cartons for
kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and
parts may not easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Tools required for assembly: Phillips Screwdriver, one 9/16” Wrenches, Two 7/16” Wrenches (Ratchet and 9/16”, 7/16” Sockets are
recommended and can be substituted for wrenches), Rubber Mallet or Hammer.
6. An electric screwdriver is helpful in assembly. However, please set at low torque and use caution because you could over-tighten the
and strip the screws out of the wooden table top.
7. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for
replacement parts.
P R E - A S S E M B L Y T I P S
2015 Escalade Sports
Ó

23
#10-24 X 1/2 Phillips
Pan Head Screw
1/4"
Plastic
Washer Washer
Plastic
3/8"
28 30
31
32 5
34
35 37
1/4-20 X 3 1/4 Carriage Bolt #8 X 9/16
SMS
#8-32 X 1 1/4
Sheet Metal Screw 3/8" Long Spacer
3/4" Long Spacer
39
36
1/4-20 X 2 3/4 Hex Head Bolt
29
HARDWARE IDENTIFIER
3/8-16
Nyloc
Locknut 1/4-20 X 1 1/2 Phillips
Truss Head Screw
1/4-20 Nyloc
Locknut
27
3/8-16 x 3 1/2 Hex Head Bolt
3/8-16X2 3/4 Hex Head Bolt
13
(Qty. 4) (Qty. 12)
(Qty. 8)
(Qty. 12)
(Qty. 4) (Qty. 4) (Qty. 176)
(Qty. 4) (Qty. 4) (Qty. 4) (Qty. 12) (Qty. 8)
(Qty. 8)
3/8 Push Nut
11
(Qty. 4)
38
(Qty. 4)
1/4-20 Wing Nut
(Qty. 4)
44
#10-24 Locknut
(Qty. 4)
Sorting your hardware ahead of time will speed up assembly time. Sort all your hardware now so it will be
ready before you start assembly.
NOTE:
3

1A. Attach Caster Wheels (#9 & #10) to Caster Beam. Slide a Caster Wheel with Lock (#10) through Caster Beam (#8) and
secure it with a Push Nut (#11) as shown in Figure 1. Gently tap the Push Nut (#11) with a hammer or rubber mallet to
secure it in place. On the other end of the Caster Beam attach a Caster Wheel without Lock (#9). Make sure you have one
Caster Wheel with Lock and a Caster Wheel without Lock for each Caster Beam. Repeat step for second Caster Beam.
1B. Attach Tube Plugs (#14) to Caster Beams (#8) as shown in Figure 1.
Caster
with
Lock
Caster
without
Lock
11
HARDWARE NEEDED
3/8 Push Nut
(Qty. 4)
NOTE: Make sure logo is
right side up and
facing as shown.
1
Figure
ASSEMBLY TIP
On the top of each page you will find a picture of the
Hardware Needed (to scale) along with the Quantity,
Key# and Description. You can lay the hardware on
the picture to identify and sort the hardware.
Having a second person sort hardware and
hold parts will speed up assembly time
and make it easier to assemble your table.
NOTE:
9
10
11
14
8
4

8
10
10
43
2. Lay Support Plates (#43) on Caster Beam (#8) to line up holes, the distance between middle
holes to side holes is different, see Front View of Figure 2. Attach Stop Spools (#12) and
Support Plates (#43) to side of Caster Beam without logo with Bolts (#13) and Nuts (#28)
but DO NOT tighten completely yet this will be done in a later step. See Figure 2.
Repeat step for second Caster Beam.
13
28
43
12
8
Longer
Shorter
Longer
Shorter
Match holes in Support Plate (#43)
with Caster Beam (#8).
2813 3/8-16 X 2 3/4 Hex Head Bolt
(Qty. 8) 3/8-16 Locknut
(Qty. 8)
Front View
HARDWARE NEEDED
Logo on
this side
2
Figure
5

Note: Support Plate (#43)
must be on inside of Caster
Rail (#8) as shown.
8
43
8
32
32
31
31
3. Attach Wood Bottom Board (#15) to Caster Beam
Assemblies (#8) as shown in Figure 3. Turn Caster Beams
as shown and attach board with four Carriage Bolts (#31)
and four Wing Nuts (#32). Tighten Wing Nuts securely.
32
31
(Qty. 4)
1/4-20 Wing Nut
HARDWARE NEEDED
1/4-20 X 3 1/4 Carriage Bolt
(Qty. 4)
NOTE: Make sure logos are right side up and
facing the outside as shown.
Caster
with
Lock
Caster
with
Lock
15
3
Figure
READ AND FOLLOW ALL ASSEMBLY, OPERATING, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO (2)
ADULTS ARE NEEDED TO PUT THIS TABLE TOGETHER!
6
CAUTION

4. Attach Strut Tubes (#17) and Linkages (#16) to Caster Beam Assemblies (#8) as shown in Figure 4.
a) Loosen Bolts (#13) and Nuts (#28) so that Strut Tube (#17) can fit between Support Plate (#43) and Caster Beam
(#8) as shown in the Top View and Figure 4.
b) Slide one Hex Bolt (#27) through Caster Beam (#8), one Plastic Washer (#39), Strut Tube (#17), Plastic Washer
(#39), Support Plate (#43) Spacer (#36), Linkage (#16) and Locknut (#28) as shown in Figure 4 and Top View.
c) Repeat on other end of Caster Beam (#8) and on second Caster Beam.
d) Tighten Bolts (#13) and Nuts (#28) (installed in Step 2) securely.
e) Tighten Nuts (#28) on Bolts (#27) securely but DO NOT over tighten, Strut Tube
must Pivot Freely.
3/8-16
Locknut
(Qty. 4)
28
HARDWARE NEEDED
27 3/8-16 x 3 1/2 Hex Head Bolt
(Qty. 4)
36 39
3/4" Long Spacer
(Qty. 4)
3/8" Plastic
Washer (Qty. 8)
Top View
27
39
36
28
17
43
12
16
13 13
8
Note: Linkages and Strut
tubes must be turned as
shown or table will not
operate correctly.
8
16
17
16
27
36
28
39
17
28
4
Figure
7

5. Lay Table Top (#1) painted side down, on a smooth, flat surface. Use the shipping
container to protect the painted surface of table top.
6. Align the ”U” Support (#21) on Table Top (#1) as shown in Figure 5.
7. Align all four holes in each U-Clip (#22) with the four Indentations in table top. Be sure that Slot
in the Three U-Clips (#22) all face the same direction toward the end of the table with no stripe
and no Indentations. Secure U-Clips (#22) with Screws (#5) as shown in Figure 5 & Detail A.
Note: All four holes in the U-Clip (#22) must align with four Indentations in table top. See Detail A.
Note: All Indentations
guides in table top are
small so look closely.
Note: End with no stripe
and no Indentations.
5
Figure
8. Rotate U-support (#21) that is on bottom of Table Top
until you see the screw holes in the slots of U-clips (#22).
If necessary Slide U-support (#21) side to side and back
and forth to see holes. See Figure 5 & Detail B.
9. Insert Screw (#35) through slot in U-clip (#22) and into U-support
(#21). See Figure 5 & Detail B. Thread screw all the way into U-
support until it touches the back of the tube. There should be about
3/8” of screw (#35) left sticking out. Repeat for second Screw (#35)
and U Clip (#22).
Note: To aid in assembly you can use a cordless drill and
Phillips bit. Wear safety glasses.
Or
Scan with your smartphone:
Detail A
21
22
35
1
5
21 22
Slot in
U-Clip
1
Detail B
35 #8-32 X 1 1/4
Sheet Metal Screw
(Qty. 2)
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 12)
If you want to see a video on how to insert Screw (#35) go to:
http://www.escaladesports.com/customer-service/instruction-videos
WHEN ASSEMBLING TABLE, IT IS EXTREMELY IMPORTANT THAT THE U-CLIPS (#22) BE TURNED
AS SHOWN HERE. IF U-CLIPS ARE TURNED INCORRECTLY, YOU WILL DO IRREPARABLE DAMAGE
TO YOUR TABLE WHEN YOU ATTEMPT TO OPEN IT TO THE PLAYING POSITION.
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE AND USE CAUTION
BECAUSE YOU COULD OVER-TIGHTEN THE HARDWARE AND STRIP SCREW IN WOOD
DOING IRREPARABLE DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
8
NOTICE NOTICE

10. Assemble parts to the bottom of the table top with Screws (#5) as shown in Figure 6,
Detail C and Detail D.
a) Align the holes in the Mounting Brackets (#25) & (#20) with Indentations in table
top assembly and secure with screws (#5) as shown. All holes in each Mounting
Bracket must align with Indentations in the top. See Figure 6 and Detail C.
b) Align the holes in the two U-Support Clips (#6) with Indentations in table top. Be
sure that the two U-Support Clips (#6) are positioned exactly as shown in Figure 6 &
Detail D.
20
25
5 5
Detail C Note: Indentations
in table top are small
so look closely.
6
5
Detail D
6
6
Figure
5
HARDWARE NEEDED
#8 X 9/16 Screw
(Qty. 28)
IF USING AN ELECTRIC SCREWDRIVER PLEASE SET AT LOW TORQUE
AND USE CAUTION BECAUSE YOU COULD OVER-TIGHTEN THE
HARDWARE AND STRIP SCREW IN WOOD DOING IRREPARABLE
DAMAGE TO THE TABLE. DO NOT OVER TIGHTEN SCREWS!
9
NOTICE

7A
Figure
7B
Figure
Note: You Will Need one hinge in position A and one in position C for the next page. Hinges
are universal and can be rotated into either position A or C. See Figure 7A. Or
Scan with your Smartphone/Tablet:
If you want to see a video on how to rotate hinges go to:
http://www.escaladesports.com/customer-service/instruction-videos
1. Determine in which position your hinges are rotated, if you already have one hinge in Position
A and one in Position C continue to next page.
2. If you have two hinges in Position A rotate one hinge into position C as shown in Figure 7A.
3. If you have two hinges in Position C rotate one hinge into position A as shown in Figure 7B.
FLIP HINGE ASSEMBLY
180 DEGREES
ROTATE BRACKET
180 DEGREES.
NOTE MAKE SURE TO
ONLY ROTATE BRACKET
AND NOT THE ENTIRE
HINGE ASSEMBLY.
ABC
CB A
FLIP BRACKET 180
DEGREES.
NOTE MAKE SURE TO
ONLY FLIP BRACKET
AND NOT THE ENTIRE
HINGE ASSEMBLY.
FLIP HINGE ASSEMBLY
180 DEGREES
Rotating hinge from position A to position C.
Rotating hinge from position C to position A.
NOTE:
10