Escea IB850 User manual

630099_2 Square Fascia Installation Manual AUS.doc
IB850, IB1100
Square Fascia Installation Manual
AUSTRALIAN EDITION
Important:
The appliance shall be installed in accordance with;
This installation instruction booklet.
Must be installed by a qualified person
This Manual replaces section 21.0 of the IB Series Installation Manual
This appliance is not intended for use by young children or infirm persons unless they have been
adequately supervised by a responsible person to ensure that they can use the appliance safely.
Young children should be supervised to ensure that they do not play with the appliance.
Manufactured by: Escea Ltd, PO Box 5277 Dunedin NZ, Ph: [phone], email: [email protected]
For contact details of your local escea distributor or dealer please visit www.escea.net

630099_2 Square Fascia Installation Manual AUS.doc
2
Fitting the Square Fascia Panels:
To avoid scratches or knocks to the fascia panels of this gas fireplace they must be fitted at
the complete conclusion of the installation process. It may be necessary to use the Outer
Fascia to initially locate the gas fireplace but then remove it again so that there is no chance
of damage.
Note: Never Ever Rub the Fascia Panels.
Step 1: Replace the glass.
Note: If the glass gasket requires
a replacement, call your nearest
Escea agent who will ensure the
part is replaced with the correct
type. In the event that the glass is
broken by impact, purchase the
replacement from an authorised
Escea agent only.
Step 2:
On the right hand outer side of the firebox there are four existing mounting holes, these are
located at the front bottom corner. To fit the right hand fascia mounting bracket, align the
part with the screw holes then screw in the four pozi-drive screws until tight. This added part
will hold one of the male attachments for the fascia.

630099_2 Square Fascia Installation Manual AUS.doc
3
Step 3:
The next step in attaching the square fascia mounts, is to remove the existing left hand
fascia bracket attached to the control box on the front left hand side of the firebox. Using a
screwdriver, carefully screw out the two screws holding the left hand bracket in place.
Remove this bracket. Replace with the new left hand fascia mounting bracket using the
screws for the previous bracket, these holes will line up with the previous screw holes.
Step 4:
For the Outer Fascia to fit correctly, the two existing lower magnets and fixings must be
removed. The fascia mounting flanges must also be modified. To do this, bend the flange
towards the center of the fire, making sure it is clear from the outer fascia when fitted.
Remove ma
g
nets and bolt.
Bend flan
g
e inwards or remove.
Remove Existin
g
bracket

630099_2 Square Fascia Installation Manual AUS.doc
4
Step 5: Hang the Outer Fascia (larger one)
from the 45degree flange at the top
of the firebox. Once the Fascia is
hung on this flange it will swing down
and clip into place. Once it has
clipped onto the firebox the Fascia
should be parallel with the wall.
Step 6: Attach the Inner Fascia Brackets to the
bottom of the Inner Fascia (smaller
one) as per the diagram supplied with
the Inner Fascia. Hang the top edge of
the Inner Fascia from the lip that
extends at 45 degrees from the top of
the firebox. Be very careful not to
damage the powdercoating on the
Outer Fascia. This fascia is fixed at its
base by two screws. Leave the screws
loose enough to be able to adjust the
Inner Fascia.
Diagram illustrates a cut through section of fire
Step 7: Check that the Inner Fascia is centered.
If this panel is not centered, adjust the
Inner Fascia side to side until the
spaces on either side are even. Tighten
the screws to fix the Inner Fascia in
place.
Outer Fascia
Inner Fascia
Glass