Esi Kata2-ms series User manual

installation instructions

Kata2-MS™

Model #KATA2-MS-DC-SLV

Model #KATA2-MS-DC-BLK

Model #KATA2-MS-DC-WHT

Model #KATA2-MS-GM-SLV

Model #KATA2-MS-GM-BLK

Model #KATA2-MS-GM-WHT

dual monitor arm with sliders

Page 2

Kata2-MS Components and tools

Please review these instructions before beginning the installation. Use the illustrations below to check that all the components needed for your

installation were provided with your order. Do not discard the packaging until the product works to your satisfaction.

Components and tools

Additional tools required

• Phillips screwdriver

Caution

• Hand tighten screws only. Do not use power tools.

for clamp mounting method:

monitor arm assemblies (2) and

clamp base assembly (1)

for both mounting methods:

grommet base assembly (1)

grommet base cover (1)

for optional

grommet mounting method:

monitor arm assemblies (2), plus...

grommet bar (1)

M4x10

grommet knob (1)

VESA plate screws (8)

cable clips (2)

clamp base assembly

not included when

optional grommet

mounting is ordered

M4x6 set screws (2)M4x9 set screws (4)

M4x15

VESA locking screws (2)

VESA mount assemblies (2)

dual Allen key (1)

2mm and 4mm

Page 3

Kata2-MS Assembly

Step# 1: clamp base assembly to worksurface

The thickness of the worksurface must be between 0.5" and 2.1".

• Loosen the clamp suciently to be able to slide it easily onto the worksurface.

• Clamp the assembly to the worksurface in the desired position. Be sure to

tighten the clamp securely.

Step# 2: assemble slider mounts

IMPORTANT: When assembling the slider mounts, the groove on the slider bar must be at the bottom.

• Slide the VESA mount assembly onto the slider bar. Center the assembly on the slider bar.

• Install the M4x9 set screw into the bottom of the VESA mount assembly. Using the 2mm Allen key, tighten the set screw to hold the assembly in place. Be sure the

screw tip ﬁts into the groove on the slider bar.

— After the monitor has been installed, the VESA mount can be moved anywhere along the slider bar by loosening the locking screw no more than one full turn, so that

it stays inside the groove. Be sure to re-tighten the screw to secure the monitor in the desired position.

If using optional grommet mounting method:

• Replace step 1 with steps A and B on page 7. Then return to this page and start with step 2 below.

clamp to

worksurface

0.5" – 2.1"

slider bar

VESA mount

assembly

2mm

Allen key

slider mount set screw

M4x9

groove

Page 4

Kata2-MS Assembly

Step #3: attach VESA plates to monitors

• Remove each VESA plate from its VESA mount by pushing forward the tab at the top and lifting upward.

—TIP: Practice re-installing the VESA plate before attaching it to the monitor. This will make step 3 easier.

• Place each monitor face down on a ﬂat surface. Align the VESA plate holes with the holes on the back of the monitors. Attach the VESA plates using the four VESA plate

screws per monitor.

— There are two sets of four holes on the VESA plates. One set has holes 3.9" (100mm) apart, the other set has holes 3" (7f) apart. Use the set that matches the holes

on the rear of each monitor.

lift o VESA plate

VESA plate screw

VESA

plate monitor

(face down)

top

3.9"

(100mm)

(75mm)

push tab forward

Step #4: attach monitors to VESA mounts

• Slide each VESA plate (with monitor attached) back onto its VESA mount.

— Make sure the VESA plates click securely in place.

• OPTIONAL: Secure each VESA plate to the VESA mount using the M4x15

VESA locking screw, as shown below.

attach

monitor

VESA

mount

VESA

plate

2mm Allen key

VESA locking screw

M4x15

Page 5

180°

monitors

not shown

dual Allen key

2mm end

M4x9

Kata2-MS Assembly

Step #5: install lockout set screws, if desired

Default rotation of the monitor arm assemblies

is 360°. Installation of lockout set screws limits

rotation to 180°.

• To lockout rotation of a monitor arm assembly,

install a set screw in the upper hole in the

recessed portion of the straight arm. Tighten

the screw, then back it o one turn.

• The monitor arm assembly must be in its

allowed range of rotation when installing

the lockout set screw.

Step #6: organize cables and cords

• Remove the cable covers from each monitor arm by sliding

them upward.

• Capture the cables and cords with the cable covers. Slide the

cable covers downward to attach them to the monitor arms.

• Snap the cable clips into groove at the bottom of the straight

arms. Position the opening on the clips toward the rear.

• Route the monitor cables and power cords toward the rear

by slipping the cords into the opening on the cable clips.

install covers

over cables

remove cable

covers

slide up

slide

down

capture

cables

with clip snap on

cable clip

Page 6

Kata2-MS Assembly

Step #7: make any necessary adjustments

There are ﬁve possible ways to change the position of the monitors to maximize the eciency and comfort of the working environment:

1. Monitor position on slider

— To move the monitors from side-to-side, use the 2mm end of the dual Allen key to loosen the set screw (M4x9) on the bottom of the VESA mount assembly, then

slide the monitor along the slider bar. Do not loosen the set screw more than one full turn — the tip of the set screw must remain inside the groove on the slider bar

so that the mount assembly cannot slide o the ends. Re-tighten the set screw when the monitors are positioned where desired.

2. Monitor swivel

— Use the 4mm end of the dual Allen key to adjust the underside screw behind the slider bar for the desired ease of monitor rotation.

3. Monitor arm swivel

— Use the 2mm Allen key to adjust the bottom set screw (M4x6) in the recessed area of the straight arm for the desired ease of rotation.

4. Monitor tilt

— To change monitor tilt angle, use the 4mm Allen key to loosen the screw on the side of the VESA mount. Tighten the screw to hold the angle.

5. Motion arm weight adjustment

— Use the 4mm Allen key to adjust the screw at the top of the ﬁxed arm for the appropriate monitor weight. When adjusted properly, the monitor weight is balanced,

making it easy to raise or lower the monitor.

monitors

not shown

behind

slider

M4x6

Page 7

Kata2-MS Optional grommet mount assembly

Step A: attach grommet base assembly to worksurface

• Place the base assembly over the grommet hole with the bolt centered. Fit the base cover over the base.

• Insert the grommet bar onto the grommet bolt and then screw on the grommet knob. Tighten the grommet knob securely to hold the base assembly in position.

Step B: install monitor arms into grommet base assembly

• Insert the monitor arm assemblies onto the stems on the grommet base. (If necessary, loosen the set screw ﬁrst.)

— The tabs on the bushings ﬁt into notches in the bottom of the monitor arm assemblies.

• Tighten the set screw on each monitor arm.

• Check the ease of rotation of the monitor arm

assemblies. If you need to adjust it, do so by

loosening or tightening the set screw.

install monitor

arm assemblies

tab

tighten set screw

M4x6

Go to step 2 on page 3 and proceed sequentially

center bolt in grommet hole

grommet base assembly

maximum thickness = 1.7"

base cover

tighten grommet knob to secure

grommet bar

LIMITED WARRANTY

ESI warrants this product to be free from defects in manufacturing for a period of 15 years from the date of original purchase. This warranty extends only to the original purchaser, and does not apply

if the product has been damaged or fails to function properly as a result of misuse, abuse, modiﬁcation, alteration, or improper cleaning or maintenance. This warranty does not apply to damage

in shipment caused by carriers, damage caused during installation, normal wear and tear, or excessive use (meaning consistent use in excess of an eight hour shift). ANY IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE. ESI’s sole obligation under this warranty or

any implied warranty, and the purchaser’s sole remedy, i s limited to the repair or replacement, at ESI’s option, of the product or any defective part. Costs (such as installation, labor fees or express

shipping) incurred due to replacement of products are not covered under warranty. IN NO EVENT SHALL FELLOWES, ITS AFFILIATES, SUBSIDIARIES, RELATED ENTITIES OR THEIR RESPECTIVE OFFICERS,

DIRECTORS, OR EMPLOYEES, BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY, OR SPECIAL DAMAGES.

To make a warranty claim, contact ESI at 800-833-3746 or customerser[email protected]om. You must provide proof of purchase, such as the original purchase order number.

The duration, terms and conditions of this warranty are valid worldwide, except where dierent limitations, restrictions or conditions may be required by local law.