EspressoWorks All-in-One Barista Series User manual
FAQs can be found at www.espresso-works.com
Email us for any unanswered questions: cs@espresso-works.com
FOR PRODUCT REGISTRATION, PLEASE VISIT WWW.ESPRESSO-WORKS.COM
Read this booklet thoroughly and save these instructions.
Quick Start
Guide
BARISTA SERIES
ESPRESSO & CAPPUCCINO MAKER
With ELECTRIC COFFEE GRINDER, BARISTA ACCESSORIES,
DOUBLE WALLED CAPPUCCINO GLASSES & ESPRESSO CUPS
1
WARNING : When using
electrical appliances, basic safety
precautions should always be
followed, including the following:
1. Read all instructions.
2. This appliance has been
incorporated with a grounded plug.
Please ensure the wall outlet in your
house is well earthed.
3. Do not touch hot surfaces. Use
handles or knobs.
4.
shock and injury to persons do not
immerse cord and plug in water or
other liquid.
5. Unplug from outlet when not
in use and before cleaning. Allow
to cool before putting on or taking
off parts, and before cleaning the
appliance.
6. Do not operate any appliance
with a damaged cord or plug or
after the appliance malfunctions, or
was dropped or damaged in any
manner. Please contact us at
cs@espresso-works.com to arrange
for examination, repair or electrical
or mechanical adjustment.
7. Close supervision is necessary
when any appliance is used by or
near children.
8. Do not let the cord hang over
edge of table or counter, or touch hot
surfaces.
9. Do not place on or near a hot gas
or electric burner, or in a heated oven.
10. Do not use outdoors.
11.The use of accessory attachments
not recommended by the appliance
electric shock or injury to persons.
12. Always attach plug to appliance
To disconnect, turn any control to “off,”
then remove plug from wall outlet.
13. Do not use appliance for other
than intended use and place it in a
dry environment.
14. Scalding may occur if the lid is
removed during the brewing cycles.
15. Be sure that handles are
assembled and fastened properly.
16. See instructions regarding
Handles on below Page.
17. WARNING: To avoid the risk
of injury, do not open the brew
chamber during the brew process.
18. Children should be supervised to
ensure that they do not play with the
appliance.
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS. HOUSEHOLD USE ONLY.
INCLUDED IN YOUR PURCHASE
STAINLESS
STEEL FOLD
DOWN
ESPRESSO
CUP SUPPORT
BUILT-IN MILK
FROTHER &
RESERVOIR WITH
ADJUSTABLE
CONTROL KNOB
120V PLUG-IN
ELECTRIC
COFFEE
GRINDER
EASY CLEAN
REMOVABLE
DRIP TRAY
PORTAFILTER
WITH
BAKELITE
HANDLE
16 CAPPUCCINO ART
STENCIL TEMPLATES
MEASURING
SPOON &
TAMPER
1.4L LARGE
DETACHABLE
WATER TANK
WITH HANDLE
2 HIGH QUALITY
DOUBLE WALLED
CAPPUCCINO
GLASSES
2 PREMIUM
DOUBLE WALLED
ESPRESSO CUPS
BUILT-IN
QUICK CUP
WARMER
FILTERS
• 1 X SINGLE
SHOT BASKET
• 1 X DOUBLE
SHOT BASKET
32
1. Unpack the items supplied and check them for completeness and transport damage. If the machine or the power cord has
2.
NOTES
• Never remove the rating plate.
• Keep the original packaging during the warranty period of the machine so that the machine can be properly packaged up if
it needs to be returned. The warranty claim shall lapse if any damage is caused during transport.
KEY
1 Cup warmer
2 Brew head
3
4 Fold down espresso cup support
5 Cover for the drip tray
6Drip tray
7Water tank lid
8 Water tank
9Control panel
10 Release button for milk frother and reservoir
11 Milk froth dial
12 Milk frother and reservoir cover
13 Milk nozzle lever
14 Milk nozzle
15 Milk frother and reservoir
TECHNICAL DATA
Model number: AEW-3000
Voltage supply: 120 V ~ 60 Hz
Power: 1250W
Pressure: 19-bar pump pressure system
Capacity:
• Water tank: max. 1.4 liters
• Milk frother and reservoir: 390 ml
• Cappuccino glasses: 310 ml
• Espresso cup: 80 ml
• Filter (single cup): 7g coffee powder
• Filter (double cup): 14g coffee powder
7
8
9
10
1
2
3
4
5
6
11
12
13
14
15
CONTROL PANEL ON / OFF button
SINGLE button DOUBLE button
Red Indicator Light
Yellow Indicator Light
CAPPUCCINO button LATTE button
MILK FROTH button CLEAN button
1.
2. Set up the machine in a suitable location, following the safety instructions and the notes provided in this guide.
3. Completely unwind the mains cable and plug into a properly installed power outlet that is easily accessible.
4.
i. Plug the machine into the power source.
iii. Fill the water reservoir with water.
v. Place a suitable sized cup under the brew head.
vi. Press the “CLEAN” button, and the machine will draw water through and clean the system.
vii. Once completed, the blue buttons will remain illuminated. The machine has unclocked and is now ready for
operation after cleaning.
5. Caution. Do not drink this water.
6. Clean the machine and accessories (refer to Cleaning and Maintenance chapter on page 17).
NOTE
•
•
odor to be produced. This is normal and not a machine defect.
• Do not place the machine below kitchen wall units or similar cupboards. The rising steam could cause damage to them.
• The surfaces of furniture may possibly contain elements which can attack and soften the adjustable feet of the machine. If
necessary, place a suitable pad below the adjustable feet.
• Do not operate the machine without water. If this does happen, the machine issues an error message (the red indicator light
Troubleshooting Your Machine chapter on page 11.
• Do not pour milk or other liquids into the water tank. Use only water to make coffee.
• Only pour milk or if necessary water for cleaning into the milk reservoir.
•
• Do not use the machine without a suitable container below the brew head and the milk nozzle.
COFFEE GRINDER
• Never use attachments or accessories that are not recommended by the manufacturer. They may cause malfunction or injury.
• Make sure there is no hard object in the grinder chamber before use. This may cause damage to the appliance and personal
injury to persons.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
• This appliance is for household use only. Do not use it for professional catering.
• Do not use the appliance outdoors.
BEFORE INITIAL USE
• This machine is only intended to be used to make specialty coffees using coffee powder and cool milk.
• This machine is only designed for use in a personal household and is not intended for commercial applications.
• The machine should only be used as described in the operating instructions. Any other use is deemed to be improper.
INTENDED USE
54
POWERING UP YOUR MACHINE
STEP 1 INSERT THE DRIP TRAY
Place the cover on the drip tray and
slide into the machine as shown.
STEP 4
NOTE:
cappuccino, latte macchiato or single
cappuccino, strong latte macchiato or
double espresso.
STEP 7
Plug the machine into a 110/120V
power outlet.
STEP 2
Place the machine in an open space
surface.
STEP 5
Using the measuring spoon and tamper
Clean the excess coffee from the rim.
NOTE
too tightly. Packing too tightly may
STEP 8
Press the “On / Off” button. The
heating process starts and the control
and stays lit, it means the heating
process is done. Press any of the
function buttons (Single/Double/
Cappuccino/Latte/Milk Froth) to enjoy
your coffee.
STEP 3
Open the water tank located at the back
of the machine. Open the lid and lift
out the tank using the provided built-in
handle. Fill it with cold water and do not
exceed the marking. Carefully slide
the water tank back in position. Once
secured, close the tank lid.
STEP 6
brew head. Twist anticlockwise and
secure it. Place an empty cup under the
STEP 9 AUTO OFF FUNCTION
The machine will turn off automatically
after 30 minutes of no usage, and has an
automatic boil-dry protection function.
Press the “On/Off” button to switch it
on again.
PREPARING SINGLE / DOUBLE ESPRESSO
STEP 1
Fill the water tank with water, tamper
Power the machine on and wait until the
STEP 4
Press the button for a single espresso
or button for a double espresso in
the control panel.
NOTE: I
inserted, only these two buttons will be
lit up when the machine is in stand-by
mode.
STEP 2
If desired, pre-warm the cups by placing
the cups on the cup warmer for about
5-10 minutes.
STEP 5
The machine emits a “beep” sound and
brewing process begins.
STEP 3
Place a suitable cup under the brew
head.
NOTE:
STEP 6
When the brewing process is done,
another “beep” will sound. The control
panel will be fully lit up and the machine
will switch to the stand-by mode
automatically.
NOTE
• You can program your own perfect amount of espresso. Please see the Programming Quantities chapter on page 10.
76
STEP 1
Fill the water tank with water, tamper
STEP 4
Fold out the milk nozzle using the lever.
Turn the dial on the milk reservoir cover
for the milk froth.
STEP 6
Press the button for cappuccino
or the button for latte macchiato. A
“beep” sound will be emitted and the
the brewing process is done, another
“beep” will sound. The control panel
will be fully lit up and the machine
will switch to the stand-by mode
automatically.
STEP 2
Press the release button while pulling
the milk reservoir out from its position
concurrently. Remove the milk reservoir
cover by pressing the release button on
STEP 5
Place a suitable cup under the brew
head and milk nozzle. Power the
machine on and wait until the control
STEP 3
Pour milk in the milk reservoir over
the “MIN” label. Do not exceed the
marking. Place the cover and milk
correctly with a click sound. Do not use
hot milk.
PREPARING CAPPUCCINO / LATTE MACCHIATO
NOTE
• You can program your own perfect amount of espresso and milk. Please see the Programming Quantities chapter on page 10.
STEP 1
Fill the water tank with water. Fill the
milk reservoir. Fold out the milk nozzle
(please refer to the section on page 7).
STEP 2
Select the setting you want using the
dial. Place a suitable cup below the milk
nozzle. Power the machine on and wait
NOTE
to the top right. For more hot milk, turn
STEP 3
Press the button. A “beep” sound will
be emitted and the selected function
process is done, another “beep” sounds
The control panel will be fully lit up and
the machine will switch to the stand-by
mode automatically.
FROTHING THE MILK
DIFFERENT BREWS WITH YOUR MACHINE
NOTES
• You can program your own perfect amount of milk. Please see the Programming Quantities chapter on page 10.
ESPRESSO AMERICANO
CAPPUCCINO MACCHIATO
98
PROGRAMMING QUANTITIES
Both the quantity of espresso and the quantity of milk can be programmed for each function. This allows you to set the perfect
quantity of espresso and milk to suit your own taste. The set quantities are saved until a new quantity is set.
ESPRESSO, DOUBLE ESPRESSO, MILK FROTH
1. Fill the machine as if a specialty coffee is to be prepared (see the Powering Up Your Machine chapter on page 6).
2. If necessary, fold out the milk nozzle using the lever.
3. Place a suitable cup below the brew head or the milk nozzle.
4. Select the function that is to be reprogrammed. Press the appropriate button (a beep will sound) and keep it held down (another
beep will sound).
5. The machine starts to prepare espresso or make milk froth.
6. Only let go of the button once the quantity of milk or espresso that you want has passed through. You will hear three beeps. This
quantity is now saved under the corresponding function.
CAPPUCCINO AND LATTE MACCHIATO
This process must be carried out twice for latte macchiato and cappuccino: once for the quantity of espresso and once for the
quantity of milk:
1.
nozzle is folded out and there is a cup below the milk nozzle.
2. Start a second operation by pressing the appropriate button again. A beep will sound.
3. Wait until the quantity of milk has passed through.
4. As soon as the machine starts to make espresso, press the appropriate button again and hold it down. Another beep will sound.
5. Only let go of the button again once the quantity of espresso that you want has passed through. You will hear three beeps. Now
both the quantity of milk and the quantity of espresso are saved under the appropriate function.
RESET TO FACTORY SETTINGS
If the amount of espresso and amount of milk are to be reset to the amounts preset in the factory, proceed as follows:
1. Switch off the machine via the “On / Off” button.
2. Press the and buttons simultaneously and keep them held down.
3.
4. Let go of the and buttons. The amounts have now been reset to the factory settings.
1. Carefully unpack your espresso machine and remove all packing material. Wipe the grinding chamber, blades with a damp
2.
3. Pour coffee beans into the grinding chamber. Do not use more than 30g of coffee beans.
4. Secure the lid into the motor base. Align the arrow with the “” marking on the motor base.
5. Connect the coffee grinder to the power supply.
6.Turn the lid clockwise to the “” mark on the motor base. The coffee grinder will operate. Hold the lid at the “” position.
7. If the lid is released, it will return to the “” position and the coffee grinder will stop operating. Turn and hold the lid to the
“” position if you want the coffee grinder to operate again.
8. View the consistency of the coffee grounds from the transparent lid. Never remove the lid until the blades stop completely.
9. Once the desired ground size has been obtained, disconnect the power cable from the power outlet.
10. Remove the transparent lid and pour out the coffee ground.
NOTE
• Do not run the appliance continuously for more than 30 seconds. After a full 30 second cycle, allow the grinder to rest for
another three minutes before using it again.
USING YOUR COFFEE GRINDER
TROUBLESHOOTING YOUR MACHINE
Problem Reason Solution
The control panel does not light up /
the machine cannot be switched on.
The power cord is not inserted correctly
in the power outlet.
Insert the power cord.
The power outlet is defective. Try another power outlet.
No mains voltage is present. Check the fuse of the mains connection.
The control panel lighting is defective. Please contact us at
Too many machines connected to the
same circuit.
Reduce the number of machines in
the circuit.
No error can be identied. Please contact us at
There is too much water in the water
tank.
The water tank is not placed in its
mount correctly.
Place the water tank in the correct
position.
The drip tray is lled with water. Please clean the drip tray
The espresso machine is
malfunctioning.
Please contact us at
There is some coffee powder on the
lter edge.
Use a damp cloth to wipe away any
residual coffee powder
machine beeps constantly and the
panel does not light up.
There is no water in the water tank. 1. Detach the water tank from the
the section in the Powering Up Your
Machine chapter on page 6).
2. Place a cup underneath.
3. Press any button. Some water will run
through the water system into the
cup. The machine will stop beeping,
the red indicator light goes out and
the machine can be restarted.
4. Select the function you want again.
The red indicator light lights up
constantly.
The machine is defective. Please contact us at
The machine is clogged. Descale the machine (see the Cleaning
and Maintenance chapter on page 17).
The espresso runs very slowly into
the cup.
The brew head or the lter is clogged.
The machine is clogged. Descale the machine (see the Cleaning
and Maintenance chapter on page 17).
The espresso is too weak. There is not enough coffee powder in
the lter.
Pour the right quantity of coffee
the Powering Up Your Machine chapter
on page 6).
The set espresso quantity is too much
for the quantity of coffee powder in
the lter.
The perfect amount of espresso to suit
your own taste can be programmed
in the machine (see the Programming
Quantities chapter on page 10).
1110
espresso.
The machine was not cleaned and
there are residual coffee grounds.
Please refer to the Cleaning &
Maintenance chapter on page 17.
The coffee powder has turned bad after
being stored in a hot and wet place for
long periods of time.
Please use fresh coffee powder, or
store unused coffee powder in a cool
and dry place. After opening a pack of
coffee, reseal it tightly and store it in a
refrigerator to maintain its freshness.
During use, an unpleasant smell is
detected.
Is the machine being used for the rst
time?
A smell often develops when new
should disappear once the machine
has been used several times.
Has the machine just been descaled? Rinse out the machine with clear water.
in the brewing process.
The machine is clogged. Descale the machine (see the Cleaning
and Maintenance chapter on page 17).
Cappuccino, latte macchiato or milk
froth has been selected, but there is no
milk in the milk reservoir.
Wait until the program has run through.
Allow the machine to cool down a little.
Remove the milk reservoir from the
Preparing
Cappuccino / Latte Macchiato chapter
on page 8). Then run the program
again.
The machine is not working. The power cable was not correctly
plugged into the power outlet.
Plug the power cord into a wall outlet
and if the machine still ceases to
function, please contact us at
ABOUT THE SAFETY INSTRUCTIONS
future reference. If the machine is given to someone else, these operating instructions should also be handed over with it. The
manufacturer and importer do not accept any liability if the information in these operating instructions is not complied with.
EXPLANATION OF THE SYMBOLS
EXPLANATION OF THE SIGNAL WORDS
DANGER Warns of serious injuries and danger to life.
WARNING Warns of possible serious injuries and danger to life.
CAUTION Warns of slight to moderate injuries.
NOTE Warns of damage to property.
Danger symbol
Electric shock risk
Beware of hot surfaces
Suitable for food use
Read operating instructions
before use
The symbols below indicate risks of injury. Read through the associated safety
instructions carefully and follow them.
way and / or is utilized in some other way. Comply with the
operating instructions.
• This machine may be used by children aged 8 and over and by
people with reduced physical, sensory or mental abilities or a lack of
experience and/or knowledge if they are supervised or have received
instruction on how to use the machine safely and have understood
the dangers resulting from failure to comply with the relevant safety
precautions.
• Children must not play with the machine.
• Cleaning and user maintenance may not be performed by children,
unless they are older than 8 years of age and are supervised.
• Children younger than 8 years of age and animals must be kept away
from the machine and the mains cable.
• Keep children and animals away from the packaging material to avoid
any danger of .
WARNING :
Hot Steam or Condensation
• Avoid coming into contact with the rising steam. Keep your hands and
head away from the steam outlet openings during the brewing process.
•
•
• Never pour water into the water tank or milk into the milk reservoir
when the machine is switched on or during the brewing process.
Always switch off the machine and remove the water tank / milk
been inserted correctly before switching it on again.
• Make sure that the milk nozzle is pointing into the cup below the brew
SAFETY INSTRUCTIONS
1312
head to prevent any accidental, uncontrolled emission of hot milk
from the milk nozzle.
• Do not move the machine during the brewing process.
• The specialty coffees that are prepared are hot. Be careful when
handling hot liquids.
CAUTION :
The machine and the accessories are very hot during and
• and markings) on the milk reservoir
and water tank. Fill the milk reservoir and the water tank at least up to
the marking and no higher than the marking.
• The machine is not designed to be operated with an external timer or
a separate remote control system.
• Never immerse the machine, mains cable or power cord in water or
other liquids and ensure that they cannot fall into water or become
wet.
• The machine must always be disconnected from the mains when it
emptying the water tank or milk reservoir or cleaning it.
• In the interest of your own safety, check the machine, the mains
cable and the power cord for damage every time before use. Use the
machine only if it is in working order.
•
mains cable yourself. If the machine, the mains cable or the power
cord of the machine is damaged, they must be replaced by the
manufacturer, customer service department or authorized retailers in
order to avoid any hazards.
• Please follow the instructions in the Cleaning and Maintenance
chapter on page 17.
DANGER :
• Use the machine only in closed rooms. Do not use the
machine in rooms with high humidity.
• Should the machine fall into water, switch off the power supply
immediately. Do not attempt to pull it out of the water while it is still
connected to the mains power.
• Never touch the machine, power cord with wet hands when these
components are connected to the mains power.
• Make sure that the steam which emerges is not aimed directly at
electrical machines and equipment containing electrical components.
WARNING : D
Damage and Inappropriate Use
• Only connect the machine to a socket with safety contacts that are
properly installed and matches the technical data of the machine. The
socket must also be readily accessible after connection so that the
connection to the mains can quickly be isolated.
• Do not use the machine in conjunction with extension cables.
DANGER :
• Do not use the machine in rooms containing easily ignitable
dust or poisonous and explosive fumes.
• Do not connect the machine along with other consumers (with a high
wattage) to a multiple socket in order to prevent overloading and a
• Do not operate the machine in the vicinity of combustible material. Do
not place any combustible materials (e.g. cardboard, paper, wood or
plastic) in or on the machine.
• Do not cover the machine during operation.
•
NOTE
and Property
• The machine should only be used when it is correctly assembled. Before
1514
• Lay the mains cable in a way that it does not become squashed or bent
and does not come into contact with hot surfaces (also applies to the
hot surfaces of the machine).
• To avoid the machine from being pulled down, the mains cable must not
hang down from the surface on which the machine is placed.
• Switch off the machine and pull the power cord out of the power outlet
if an error occurs during operation, when there is a power cut or before
a thunderstorm.
• Never pull or carry the machine by the mains cable. When you pull it out
of the power outlet, always pull on the power cord and never the mains
cable.
•
temperatures, persistent moisture, wet conditions and impacts.
• Use only original spare parts from the manufacturer.
Notes on the Cord
• A short power-supply cord (or detached power-supply cord)
is to be provided to reduce risks resulting from becoming
entangled in or tripping over a long cord.
• Longer detachable power-supply cords or extension cords are available
and may be used if care is exercised in their use.
• If a long detachable power-supply cords or extension cord is used,
(a.) The marked electrical rating of the detachable power-supply cord or
extension cord should be at least as great as the electrical rating of the
appliance. (b.) If the appliance is of the grounded type, the extension
cord should be a grounding type-3 wire cord. (c.) The longer cord
should be arranged so that it will not drape over the counter top or
table top where it can be pulled on by children or tripped over.
1. Unplug your espresso machine from the power outlet and allow for it to completely cool off before cleaning.
2.
3. Rinse through the tube in the milk reservoir with clear hot water to remove milk residues after every use.
4.
5. Wipe down the housing with a damp cloth. If necessary, use a little mild detergent to remove more intense soiling.
6.Thoroughly dry the machine and all accessories before assembling it again.
7. Check the mains cable regularly for any damage.
NOTE
• Before commencing the cleaning, read the safety instructions in the Important Safeguards and Safety Instructions chapters
on page 2 and page 13 respectively.
• Do not use any toxic, corrosive or abrasive cleaning agents or scouring sponges to clean the machine. These can damage
the surface.
• Never immerse the machine in water.
• Do not use the machine without a suitable container below the brew head and the milk nozzle.
• The water tank and milk reservoir are not suitable to dishwasher.
SELF-CLEANING : QUICK CLEAN OF THE MILK RESERVOIR SYSTEM
The quick clean of the milk reservoir system should be carried out after every use so that no milk residues can remain in the
system and dry on or go moldy.
1. Fill the milk reservoir with water (see the section in the Preparing Cappuccino and Macchiato chapter on page 8).
2. Fold out the milk nozzle using the lever.
3.
process.
4. Place a suitable cup below the milk nozzle.
5.
6.
7. Repeat this process if necessary.
INTENSIVE CLEAN OF THE PORTAFILTER AND MILK RESERVOIR SYSTEM
1. Fill the water tank with water (see the section in the Powering Up Your Machine chapter on page 6).
2. Fill the milk reservoir with water (see the section in the Preparing Cappuccino and Macchiato chapter on page 8).
3. Fold out the milk nozzle using the lever.
4.
process.
5. Place a suitable cup below the brew head and the milk nozzle.
6.
7. If you want to stop the cleaning, press the button again. The machine will swi to stand-by mode.
8. Pour away the water in the cup.
9. Repeat this process if necessary.
COFFEE GRINDER
1. Always switch off and unplug before cleaning.
2. Never left the motor unit, power cable or plug get wet. Only the transparent lid can be immersed in water for cleaning.
3. Clean the lid with water and mild detergent. The lid is not dishwasher-safe. Rinse and dry thoroughly.
CLEANING AND MAINTENANCE
1716
WARRANTY
PRODUCT REGISTRATION
EspressoWorksTM strongly encourages you to register your purchase. You can register online at www.espresso-works.com
Registering your purchase will allow EspressoWorksTM to better serve you with any of your customer service needs.
WHO CAN SEEK WARRANTY COVERAGE
This warranty is extended by EspressoWorksTM to the owner of this machine for personal household use only. This warranty
does not apply to products used for commercial, rental or re-sale purposes.
WHAT IS COVERED
EspressoWorksTM warrants to the owner that if this machine fails within 1 year from the date of purchase on the purchase
receipt due to a defect in material or workmanship, EspressoWorksTM will repair or replace the failed machine or component
part of the machine. Shipping and handling charges may apply. Please retain the original purchase receipt for the duration of
the warranty period. EspressoWorksTM reserves the right to refuse a warranty repair if proof of purchase cannot be provided. In
the event of a warranty claim, please return the product with the original purchase receipt.
WHAT IS NOT COVERED
This warranty does not apply to machines that have been used commercially or in non-household applications. This warranty
does not cover cosmetic changes that do not affect performance, such as discoloration or the effects of the use of abrasives or
cleaners or food build up. This warranty is only valid if the machine is used and maintained in accordance with the instructions,
warnings and safeguards contained in the owner’s manual. The warranty does not apply in the event of failure to observe the
operating or assembly instructions.
EspressoWorksTM will not be responsible for the cost of any unauthorized warranty repairs.
NO EMPLOYEE OR REPRESENTATIVE OF ESPRESSOWORKSTM IS AUTHORIZED TO MAKE ANY ADDITIONAL WARRANTY
OR ANY MODIFICATION TO THIS WARRANTY WHICH MAY BE BINDING UPON ESPRESSOWORKSTM. ACCORDINGLY,
PURCHASER SHOULD NOT RELY UPON ANY ADDITIONAL STATEMENTS MADE BY ANY EMPLOYEE OR REPRESENTATIVE
OF ESPRESSOWORKSTM. IN NO EVENT, WHETHER BASED ON CONTRACT, INDEMNITY, WARRANTY, TORT (INCLUDING
NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, SHALL ESPRESSOWORKSTM BE LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOSS OF PROFIT OR REVENUE.
Some states do not allow limits on warranties. In such states, the above limitations may not apply to you. Outside the U.S.A. and
Canada, other warranties may apply.
For more information, visit www.espresso-works.com
4.
5. Wipe the grinding chamber and blades with a damp cloth, then dry thoroughly. Handle blades and cutting plates with care
DESCALING
espresso. The machine indicates at regular intervals that it needs to be descaled. When the yellow control lamp is lit, a
descaling process should be performed. The control lamp goes out as soon as a cleaning or descaling process has been
performed.
Limescale deposits have an adverse effect not only on the quality of the espresso and the water, but they also cause power
We therefore recommend regularly removing limescale deposits with a descaling agent in accordance with the water quality in
your area and how often the machine is used (approx. every 2 – 6 weeks).
STORAGE
Disconnect the machine from the mains power when it is not going to be used for a prolonged period. Clean the machine
again if necessary and let it dry completely.
Store the machine and all accessories in a dry, clean, frost-free place that is protected from direct sunlight and cannot be
accessed by children or animals.
Complete user instructions, FAQ and usage tips can be found at
Espresso-Works.com
MADE IN CHINA
© 2018
Email us at cs@espresso-works.com
for any unanswered questions
This symbol on the product or in the instructions means that
your electrical and equipment should be disposed at the end
of its life separately from your household wares. There are
separate collection systems for recycling in the EU. For more
information, please contact the local authority or your retailer
where you purchased the product.
FOR HOUSEHOLD USE ONLY
SÓLO PARA USO DOMÉSTICO
UNIQUEMENT POUR UN USAGE À DOMICILE
PARA UTILIZAÇÃO DOMÉSTICO SOMENTE
18
Espresso-Works.com
Other manuals for All-in-One Barista Series
2
This manual suits for next models
2
Table of contents
Other EspressoWorks Coffee Maker manuals
