Esse-ti HELPY 2W-V BASIC User manual

31/07/2019
Alarm system for elevators
compliant with the European Standard
EN 81-28:2018
HELPY 2W-V BASIC
QUICK GUIDE

Page 2 DESCRIPTION
DESCRIPTION
Autodialer specifically designed for retrofitting behind the elevator car panel.
A Connector for Esse-ti power supply
(12 Vdc)
B Micro SD Card slot
C Device status LED
D Serial port for PC connection
E Reset pushbutton
F Terminal blocks
G Built-in loudspeaker
H Given alarm indicator light
I Received alarm indicator light
L Built-in microphone
M RJ11 connector for local telephone
Helpy 2W-V Basic models
CODE POWER SUPPLY BUILT-IN LEDS
5HL-045 12 Vdc •
5HL-046 12 Vdc
5HL-047 24 Vdc •
5HL-048 24 Vdc

TERMINAL BLOCKS Page 3
TERMINAL BLOCKS
+ Power supply input 12 Vdc or 24 Vdc
- Negative
AI Given alarm indicator light (12 Vdc)
AR Received alarm indicator light (12 Vdc)
+12 12 Vdc output (max. 100 mA)
C Common terminal(1) for inputs AL1 and IN1
- Negative
AL1 Alarm input(2) 1
AL2 Alarm input(3) 2 / Auxiliary input(3) / Reset input(3)
IN1 Filter input(2) / Reset input(3)
ALT2 Output for connecting loudspeaker of passive speaker unit
MIC2 Input for connecting microphone of passive speaker unit or single
microphone
MIC3 Input for connecting microphone of passive speaker unit or single
microphone
- Negative
TEL Local telephone
RL1 Relay(4)
RL1 Relay(4)
Ground terminal for telephone line
LTI PSTN-line or universal gateway input
LTI PSTN-line or universal gateway input
(1) : can be connected to a block –, to the block +12 or to an external reference
(2) : allows to connect voltage free contact pushbuttons (NO or NC) or powered pushbuttons
(3) : allows to connect voltage free contact (NO or NC)
(4) : free contact NO

Page 4 CONNECTING THE SPEAKER UNITS
CONNECTING THE SPEAKER UNITS
Helpy 2W-V comes with a built-in speaker unit.
It is also possible to connect to the Helpy 2W-V up to 2 passive speaker units
(or cables with microphone) combined to the built-in speaker unit.
Note: the passive speaker unit can be installed at max. 6 m distance
from Helpy 2W-V by using a shielded cable.
 Connect the speaker units:
PASSIVE SPEAKER UNIT HELPY 2W-V
A ALT2
B MIC2 or MIC3
––

CONNECTING THE EMERGENCY CALL BUTTONS Page 5
CONNECTING THE EMERGENCY
CALL BUTTONS
Car pushbutton
It is possible to connect (inside the elevator car) voltage free contact
pushbuttons or powered pushbuttons.
 Connect, following one of the diagrams shown below, the car
pushbutton.
Voltage free contact pushbuttons
Powered pushbuttons (12~24Vdc) – 2 solutions

Page 6 CONNECTING THE EMERGENCY CALL BUTTONS
Passive speaker unit pushbuttons
In case of passive speaker units without built-in pushbutton it is possible to use
voltage free contact pushbuttons (NO or NC).
 Connect, following the diagram shown below, the external pushbutton.

CONNECTING THE FILTER INPUT Page 7
CONNECTING THE FILTER INPUT
 Connect, following one of the diagrams shown below, the filter contact.

Page 8 CONNECTING THE INDICATOR LIGHTS
CONNECTING THE INDICATOR
LIGHTS
The GIVEN ALARM INDICATOR LIGHT (yellow) switches on after pressing
the emergency button to indicate the beginning of the alarm procedure. The
RECEIVED ALARM INDICATOR LIGHT (green) switches on when the
alarm call is answered.
Some Helpy 2W-V models come with built-in indicator lights. It is also
possible to connect external indicator lights.
 Connect, following the diagram shown below, the external indicator
lights to the Helpy 2W-V.

OTHER CONNECTIONS Page 9
OTHER CONNECTIONS
CONNECTING THE TELEPHONE LINE
PSTN line or universal gateway (2G/3G/4G)
 Connect the ground terminal (indicated by ), to a ground socket in
order to increase the telephone line protection.
 Connect the telephone line to terminal LTI.
CONNECTING THE LOCAL TELEPHONE
 Connect the local telephone (for programming and managing the
device) directly to the RJ11 connector (M in the picture at page 2) or to
TEL and – terminals (irrespective of the polarity).
CONNECTING THE RELAY
 Connect the output RL1 (normally open contact) to the external device.
CONNECTING THE AUXILIARY INPUTS
It is possible to configure the AL2 input of Helpy 2W-V as auxiliary input (NO
or NC).
 Connect the external contact to AL2 and – terminals.

Page 10 WIRING DIAGRAM
WIRING DIAGRAM

MINIMUM OPERATIONS TO VERIFY PROPER INSTALLATION Page 11
MINIMUM OPERATIONS TO VERIFY
PROPER INSTALLATION
1. PROGRAMMING
 Access to programming: lift the local telephone handset and dial
.
The programming activated message will be heard.
 Program a telephone number for the emergency-call alarm:
dial <telephone number> .
 Record the identification message of the specific elevator, which is
meant to contain all necessary information concerning the elevator
location: dial and, after the “Correct” message, pronounce
the message and hang up.
 To listen again to the previous message: lift the handset and dial
.
 Make an external call to check the PSTN line or the universal gateway is
properly working: dial and digit the telephone number to make a test
call.
2. TESTING THE ALARM PROCEDURE
 Press the emergency call button for more than 3 seconds (factory
value).
The alarm starts.
3. ANSWERING THE ALARM
Note: the activation mode of the communication with the trapped
person can be configured with the “Two-way communication
mode during an alarm” programming (code 78).
-1st mode: automatic two-way communication established after messages
(factory default)
 Answer by the called party.
The two-way communication mode will be activated after the voice messages.
 Speak with the trapped person.
-2nd mode: two-way communication established after input of “Communication
activation” code

Page 12 MINIMUM OPERATIONS TO VERIFY PROPER INSTALLATION
 Answer by the called party.
The voice messages will be heard.
 Press to speak with the trapped person.
-3nd mode: immediate and automatic two-way communication (no messages)
 Answer by the called party.
 Speak with the trapped person.
4. RESETTING THE ALARM
Note: the alarm reset mode can be configured with the “Alarm reset
mode” programming (code 77).
-1st mode: reset by “End” code (factory default)
 Press to end the alarm.
-2nd mode: automatic reset
 Hang up (or press ) to end the alarm.
-3nd mode: automatic reset with local acknowledgement
 Hang up to end the call.
 Close the reset input (AL2 or IN1) to end the alarm.
An end-of-alarm call will be generated.
 Answer by the called party.
 Press .
If the reset input is not closed within 6 hours, the alarm is automatically ended.
Note: the reset input can be configured with the “Helpy 2W-V inputs
setting” programming (code 55).
Note: in case it should not be possible to stop the alarm procedure
remotely (i.e. the entered telephone number is incorrect)
simply lift the handset of the local telephone and dial
* <Password> # (by factory default: ) or press the
reset pushbutton.

MINIMUM OPERATIONS TO VERIFY PROPER INSTALLATION Page 13
USING THE RESET BUTTON
Note: the reset operation does not alter the previously set
parameters.
Use of the reset pushbutton (E in the picture at page 2):
- Pressing shortly
Allows to interrupt an alarm call.
By pressing shortly you get the same result as lifting the handset of the
local telephone and entering * <Password> #.
- Pressing longer (10 seconds)
Allows to reset the device.
By pressing longer, the Helpy 2W-V will be re-started with no need to
disconnect the power supply.
Note: it is also possible to reset the device through the code
995*0#.

Page 14 PROGRAMMING
PROGRAMMING
In the tables below:
 INST indicates that the programming is allowed for the installer
 OPER indicates that the programming is allowed by the maintenance technician
 factory default values are highlighted in bold
Basic programming
BASIC PROGRAMMING
ACCESS TO
PROGRAMMING
< INSTALLER or OPERATOR PASSWORD >
(factory default: )
EXITING THE
PROGRAMMING
< INSTALLER or OPERATOR PASSWORD >
(factory default: )
TELEPHONE
NUMBERS
(INST)
* the programming
of the telephone
number
automatically
activates the
alarm/call
(position
from 01 to
12)
SOURCE RECEIVER
…
(X..X =
telephone
number,
max. 20
digits;
* = 2 sec-
pause)
emergency-
call button
—
battery
alarms * USER
periodic
automatic test
call *
ESSE-TI
— CLI
——
— P100
no external
power supply
alarm
—
auxiliary
alarm
—
end of
alarm
—

PROGRAMMING Page 15
BASIC PROGRAMMING
DELETE A
TELEPHONE
NUMBER
(INST)
(position from 01 to
12)
DATE
(INST)
WEEKDAY
(dd) (mm) (yy)
SUNDAY
MONDAY
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
TIME
(INST) (hhmm; from 0000 to 2359)
RECORD
MESSAGES
(INST)
identification
message
(max. 25s ) (record) (hang up)
courtesy message
(max. 25 s)
LISTEN TO
MESSAGES
(INST/OPER)
identification
message
(listen)
courtesy message
LOW BATTERY
ALARM
(INST)
disabled alarm
enabled alarm
REPLACE
BATTERY ALARM
(with Esse-ti
power supply)
(INST)
disabled alarm
enabled alarm

Page 16 PROGRAMMING
BASIC PROGRAMMING
AUTOMATIC TEST
DATA
(INST)
Frequency (days, from 1 to 9; factory default 3)
Time (hhmm; from 0000 to 2359)
Automatic
test alarm
automatic test disabled
automatic test enabled (EN 81-28:2018)
automatic test enabled (EN 81-28:2004)
Make a test call
manually
PROTOCOLS
IDENTIFICATION
CODE
(INST)
Esse-ti
…(identification code) [ ]
P100
SPEAKER UNITS
VOLUME
(INST/OPER)
loudspeaker
(from 1 to
9; factory
default 3)
microphone
(from 1 to
9; factory
default 5)
[]
VOLUME OF
LANDING FLOOR
MESSAGES
(INST/OPER)
(from 1 to 4; factory default 3; 4=loudspeaker
volume, 3=¾ of loudspeaker volume, 2=½ of
loudspeaker volume, 1=¼ of loudspeaker volume)
LISTEN TO THE
PROGRAMMING
AGAIN
(INST)
... (programming code prefix)
RESTORE
FACTORY
SETTINGS
(INST)

PROGRAMMING Page 17
Advanced programming
ADVANCED PROGRAMMING
CHANGE THE
INSTALLER
PASSWORD “0”
(INST)
…[ ]
(old)
.. [ ] .. [ ]
(new) (new)
CHANGE THE
OPERATOR
PASSWORD “1”
(INST)
…[ ]
(old)
.. [ ] .. [ ]
(new) (new)
EMERGENCY CALL
BUTTONS DELAY
(INST)
(seconds, from 3 to 9)
EMERGENCY
BUTTONS
(AL1 AND AL2)
NORMALLY
OPEN/CLOSED
(INST)
AL1
(0=normally closed
1=normally open)
AL2
(0=normally closed
1=normally open)
HELPY 2W-V
INPUTS SETTING
(INST)
AL2=alarm input / IN1=filter input
AL2=auxiliary input / IN1=filter input
AL2=reset input / IN1=filter input
AL2=alarm input / IN1=reset input
AL2=auxiliary input / IN1=reset input
NO EXTERNAL
POWER SUPPLY
ALARM
(with Esse-ti
power supply)
(INST)
disabled alarm
enabled alarm with XX minutes delay
(from 01 to 99)
FILTER
ACTIVATION
(INST/OPER)
disabled
enabled
FILTER INPUT
NORMALLY
CLOSED/OPEN
(INST/OPER)
normally closed
normally open

Page 18 PROGRAMMING
ADVANCED PROGRAMMING
FILTER BYPASS
(INST) (seconds, from 15 to 30)
ALARM
OPERATION
WITHOUT
TELEPHONE LINE
(INST)
AI indicator light lit and courtesy message
AI indicator light unlit and no courtesy message
AI indicator light lit and no courtesy message
REPEATS OF
COURTESY
MESSAGE
DURING
AN ALARM
(INST)
(seconds between two courtesy messages, from
02 to 59; 00=no courtesy message; 01=one
courtesy message for each call)
“COMMUNICA-
TION
ACTIVATED”
MESSAGE
SETTING
(INST)
disabled message
enabled message
TWO-WAY
COMMUNICATION
MODE DURING
AN ALARM
(INST)
two-way communication established after input of
"Communication activation" code
automatic two-way communication established
after messages
immediate and automatic two-way communication
(no messages)
ALARM RESET
MODE
(INST)
automatic reset
alarm reset by “End alarm” code
automatic reset with local acknowledgement
“PLAY
IDENTIFICATION
MESSAGE” CODE
(INST)
…(from 1 to 3 digits; factory default 5)[ ]
“COMMUNICA-
TION
ACTIVATION”
CODE
(INST)
…(from 1 to 3 digits; factory default 0)[ ]
“END ALARM”
CODE
(INST)
…(from 1 to 3 digits; factory default 9)[ ]

PROGRAMMING Page 19
ADVANCED PROGRAMMING
“EXCLUSION”
CODE
(INST)
…(from 1 to 3 digits; factory default 1)[ ]
RESTORE
FACTORY
MESSAGES
(INST)
identification message
courtesy message
LANGUAGE
(INST)
(language: 00 Italian, 01 English, 02 German,
03 French, 04 Polish, 05 Portuguese,
06 Russian,07 Spanish)
MULTI-ANGUAGE
COURTESY
MESSAGE
(INST)
(second language) (third language) [ ]
TONE DECODER
(INST)
(country: 00 IT/SM/AL/BA/GM/MK/MT/NO,
01 GB/AE, 02 DE/LB/LU, 03 FR/GP/GF, 04 PL,
05 PT, 06 RU/BY, 07 ES/AD/CY, 08 BG/BR/KY/
DK/ID/IR/IS/KW/MO/MW/MX/PY/UY/VE/YE/ZM/
FO/LR, 10 HR, 11 GR/EE/FI, 12 NL/AW/VU,
13 SI, 14 HU, 15 IL, 16 AT, 17 AU/IE, 18 CH,
19 CN, 20 US/CA/JM/AI/AG/BB/BM/VG/DM/MS/
KN/TT/TC 21 BE, 22 QA, 23 SE, 24 IN, 25 TR,
26 CZ/SK/LT/MD, 27 TN/SA, 28 DZ, 29 MA,
30 RS, 31 RO, 32 JO)
DURATION OF
TWO-WAY
COMMUNICATION
DURING AN
ALARM
(INST)
(minutes, from 2to 9)
NUMBER OF
CALLS TO THE
SAME NUMBER
FOR EACH CYCLE
(INST)
(calls, from 1to 9)
CALL CYCLES FOR
EMERGENCY CALL
ALARMS
(INST)
(cycles, from 1 to 9; 0=unlimited)
CALL CYCLES FOR
TECHNOLOGICAL
ALARMS AND
TEST CALLS
(INST)
(cycles, from 1 to 9; 0=10 cycles; factory default 3)
WAITING TIME
BETWEEN
TECHNOLOGICAL
OR TEST CALLS
(INST)
(minutes, from 01 to 99;
00=30 seconds, factory default 02)

Page 20 PROGRAMMING
ADVANCED PROGRAMMING
AUTOMATIC
ANSWER
(INST)
(ring number, from 1 to 9;
0=disabled; factory default 2)
OPERATION
MODE AFTER
AUTOMATIC
ANSWER
(INST)
programming mode
direct connection with the car
CONNECTION
DURATION AFTER
AUTOMATIC
RESPONSE
(INST)
(minutes, from 1 to 9)
CLI CALL
DURATION
(CLI)
(seconds, from 00 to 99; factory default 10)
MULTI-LINK
FUNCTION
(INST)
(from 0 to 9; 1=master, 0=function disabled)
RELAY SETTING
(INST)
same behaviour as outputs AI
same behaviour as outputs AR
active for external power failure
door opener
active as long as the emergency alarm progresses
active as long as the buttons are pressed
active for telephone line absence
active for low battery
RELAY
INTERMITTENCE
(INST)
steady-state
intermittent (500 ms ON / 500 ms OFF)
LISTEN TO THE
BATTERY LEVEL
(INST)
(expressed in mV)
LISTEN TO THE
EXTERNAL
POWER SUPPLY
LEVEL
(INST)
(expressed in mV)