Esse-ti ST56 GMV User manual

19/02/2014
Alarm system for elevators
ST56 GMV
QUICK GUIDE

Page 2 HARDWARE DESCRIPTION
HARDWARE DESCRIPTION
Picture 1
A Jumper JP8 for define the behaviour of alarm inputs AL1and AL2
B LEDs indicating device operation (red) and GSM200 signal strength (green)
C Connectors for AL100 power supply
D Connectors for optional relay board
E Serial plug for connection to elevator CPU
F Reset pushbutton
G RJ11 connector for local telephone
H RJ45 connector for GSM200 module
I Connectors for optional PSTN-line board
L Connectors for FlashKey and VoiceKey
M Terminal blocks

HARDWARE DESCRIPTION Page 3
Terminal blocks
BATT 12Vdc power supply input
AR Received alarm indicator light
AI Given alarm indicator light
+12 Output 12Vdc (max. 100mA)
AL1 Alarm input 1
AL2 Alarm input 2
COM Common terminal for inputs IN1, Reset
IN1 Alarm filter input
Reset Reset input
VV2+ Output Handsfree 2
VV2- Common Handsfree 2
VV1+ Output Handsfree 1
VV1- Common Handsfree 1
TEL Local Telephone
Optional PSTN-line board
LTI PSTN-line or universal GSM gateway input
Ground terminal
Optional relay board
RL1 Relay contact 1
RL2 Relay contact 2
Remark: for the correct operation of IN1 and Reset inputs a diode
is required between terminals +12 and COM (inserted by
factory).

Pagina 4 HARDWARE DESCRIPTION
Jumper JP8 for inputs AL1 and AL2
The jumper JP8 (A in picture 1) defines the behaviour of the inputs AL1 and
AL2.
The inputs AL1 and AL2 are at +12V; the alarm occurs when they are closed to
a – terminal (ex: VV2-).
The inputs AL1 and AL2 are at 0V; the alarm occurs when they are closed to
+12V.

CONNECTING THE TELEPHONE LINE Page 5
CONNECTING THE TELEPHONE LINE
The alarm system is ready for connection over the GSM line by the proprietary
GSM200.
It allows the connection of a PSTN line or an universal GSM gateway with the
optional PSTN-line board.
GSM200 Module Connection
Make sure the jumpers are present in the dedicated connector for the PSTN-
line board, by observing the positioning below:
Picture 2
Connect the RJ45 connector (H in picture 1) to the GSM200 module by
means of the supplied cable.
PSTN line or universal GSM gateway
Remove the jumpers set in the dedicated connector for the PSTN-line board
(s. picture 2).
Insert the optional board in the dedicated connectors (I in picture 1).
Connect the PSTN line to the LTI connector placed on the optional board.
Connect the ground terminal (indicated by ), placed on the optional board,
to a ground socket in order to increase the telephone line protection.
Remark: it is recommended to keep the jumpers removed in order
to use them again in case you should wish to get back to the
GSM200 line. It is possible to place them on the connector
located on the optional PSTN-line board.

Page 6 CORRECT OPERATION CHECKLIST
CORRECT OPERATION CHECKLIST
1. PROGRAMMING
Access to programming: lift the local telephone handset and dial
.
You will hear the dialling tone (one longer tone followed by a shorter tone).
Program the telephone line type (PSTN or GSM-dedicated): dial
for GSM200 module or for PSTN line or traditional GSM
interfaces.
Program a telephone number for the emergency-call alarm:
dial <telephone number> .
Record the identification message of the specific elevator (max 22
seconds), which is meant to contain all necessary information
concerning the elevator location:
dial and pronounce the message.
To listen again to the previous message dial: .
Make an external call to check the telephone line presence:
dial and digit the telephone number to make a test call.
2. ALARM PROCEDURE CHECK
Press the emergency button for at least 2 seconds (factory default).
The emergency call will be made.
3. ANSWERING AN ALARM AND RESETTING
Answer by the called party.
Press or wait. The voice message will be heard.
Press or wait. The hands-free mode will be activated.
Press to end the alarm.
In case it should not be possible to stop the alarm procedure remotely (i.e. the
entered telephone number is incorrect) simply lift the handset of the local telephone
and dial * <Password> # (by factory default: .

PROGRAMMING Page 7
PROGRAMMING
In the tables below:
INST indicates that the programming procedure is allowed for the installer;
OPER indicates that the programming procedure is allowed for the operator;
factory default values are highlighted in bold.
PROGRAMMING
ACCESS TO
PROGRAMMING
<INSTALLER or OPERATOR PASSWORD>
(by default: )
EXITING THE
PROGRAMMING
<INSTALLER or OPERATOR PASSWORD>
(by default: )
TYPE OF
TELEPHONE
LINE
(INST)
PSTN line or universal GSM gateway
(with optional board)
GSM200 module
TELEPHONE
NUMBERS
(INST)
(position
from 01
to 12)
SOURCE: RECEIVER:
…
(X…X =
telephone
number,
max 20
digits)
emergency-
call button
ADEMCO
technological
alarm
USER
periodic
test call ESSE-TI
CLI
SMS
(only with
GSM200)
P100

Page 8 PROGRAMMING
PROGRAMMING
DATE
(INST)
weekday:
(dd) (mm) (yy)
SUNDAY
MONDAY
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
TIME
(INST)
(hhmm; from 0000 to 2359)
RECORD
MESSAGES
(INST)
identification message
(22 sec.) (beep) record
courtesy message (22 sec.)
LISTEN TO
MESSAGES
(INST/OPER)
identification message
(listen)
courtesy message
DEAD BATTERY
ALARM
(INST)
disabled alarm
enabled alarm
ADEMCO
PROTOCOL ID
(INST)
4-digits ID:
ESSE-TI/P100
PROTOCOL ID
(INST)
10-digits ID:
[ ]
AUTOMATIC TEST
DATA
(INST)
Frequency
(days, from 1 to 9; factory default 3)
Time
(hhmm; from 0000 to 2359)
Automatic test
alarm
automatic test disabled
automatic test enabled
Make a test call
manually

PROGRAMMING Page 9
PROGRAMMING
HANDSFREE
VOLUMES
(INST/OPER)
HANDSFREE 1 ... (loudspeaker’s volume;
factory default 4)
... (mocrophone’s
sensitivity; factory default 8)
HANDSFREE 2
MESSAGES
VOLUMES
(INST/OPER)
MESSAGES ... (volume)
(message factory default 2)
EMERGENCY
BUTTONS
NORMALLY
OPEN/CLOSED
(INST)
closed
open
EMERGENCY
BUTTON DELAY
(INST)
(seconds, from 0 to 9; factory default 2)
FILTER
ACTIVATION
(INST/OPER)
disabled
enabled
FILTER INPUT
NC/NO
(INST/OPER)
normally closed
normally open
ACKNOWLEDGE”
(INST)
…(from 1 to 3 digits; factory default 5)[ ]
“HANDSFREE
ACTIVATION”
(INST)
…(from 1 to 3 digits; factory default 0)[ ]
“END”
(INST)
…(from 1 to 3 digits; factory default 9)[ ]
“EXCLUSION”
(INST)
…(from 1 to 3 digits; factory default 1)[ ]
CALL CYCLES
(INST) (cycles from 0 to 9; 0 = 10 cycles; factory default 3)
HANDSFREE
CONNECTION TIME
UPON ALARM
(INST)
(minutes, from 2 to 9)
AUTOMATIC
ANSWER
(INST)
(ring number from 0 to 9; 0 = disabled; factory default 2)

Page 10 PROGRAMMING
PROGRAMMING
CONNECTION TIME
AFTER AUTOMATIC
ANSWER
(INST)
(minutes, from 1 to 9; factory default 3)
CHANGING THE
INSTALLER
PASSWORD
(INST)
…(old) .. (new) .. (new)
LISTENING TO
PROGRAMMING ... (prefix programming code)
RESTORING
FACTORY DEFAULT
(INST)

USE Page 11
USE
In the tables below:
: lift the local telephone handset;
: lift the local telephone handset and dial to access programming.
Local
LOCAL USE
CONVERSATION
WITH ALL THE
HANDSFREE
TERMINALS
CONVERSATION
OUTGOING CALLS <TELEPHONE NUMBER>
RELAY (with
optional board)
RELAY 1
RELAY 2
Remote use with ST56 in stand-by
Call ST56 and wait for the answer.
After a short series of DTMF tones followed by the elevator identification
message, dial: <INSTALLER OR OPERATOR PASSWORD> (by
default: ).
Besides the programming, the following services are available:
REMOTE USE WITH ST56 IN STAND-BY
CONVERSATION WITH ALL THE
HANDSFREE TERMINALS
ALL HANDSFREE TERMINALS
DEACTIVATE ALL
DOOR OPENER RELAY
(with optional board)
RELAY 1
RELAY 2

GMV SPA
Via Don Gnocchi, 10 - 20016 PERO – Milano (Italy)
TEL. [phone] - FAX [phone]
Strada per Biandrate, 110/112 - 28100 – Novara (Italy)
TEL. [phone] - FAX [phone]
http://www.gmv.it - e-mail: [email protected]
Esse-ti s.r.l.
Via G. Capodaglio, 9
Zona industriale Squartabue
62019 Recanati (MC) – ITALY
Tel. ++39 071 7506066 – 7506105
Fax ++39 071 7506057
www.esse-ti.it
mail: [e-mail]