Esse-ti HELPY QUICK INTL User manual

20/03/2017
Alarm system for elevators
QUICK GUIDES:
HELPY QUICK INTL
HELPY QUICK-TL INTL
ST61 INTL

DESCRIPTION Page 2
DESCRIPTION
HELPY QUICK
A Built-in loudspeaker
B Connector for Esse-ti power
supply (12Vdc)
C LED indicating device operation (red)
LED indicating GSM200 signal
strength (green)
D Connector for FlashKey
E Reset pushbutton
F RJ45 connector for GSM200 module
G Jumpers for Telephone Line /
GSM200 Module selection
H Pushbutton (two contacts):
.C2: common
.NO2: normally open
.NC2: normally closed
I Built-in microphone
L Terminal blocks

Page 3 DESCRIPTION
Terminal blocks:
+ 12Vdc power supply input or 12Vdc output (max. 100mA,
if present Esse-ti power supply)
- Negative pole
AI Given alarm indicator light
AR Received alarm indicator light
+12 12Vdc output (max. 100mA)
C Common terminal for inputs AL1 and IN1
- Negative pole
AL1 Alarm input 1
AL2 Alarm input 2
IN1 Filter input
ALT2 Output for connecting loudspeaker of passive handsfree
terminal
MIC2 Input for connecting microphone of passive handsfree or
single microphone
MIC3 Input for connecting microphone of passive handsfree or
single microphone
- Negative pole
TEL Local Telephone
RL1 Relay
Ground terminal for telephone line
LTI Telephone line input
- Negative pole
V + Pit active handsfree

DESCRIPTION Page 4
HELPY QUICK-TL
A Connector for external LEDs
B Connector for built-in loudspeaker
C Built-in loudspeaker
D Connector for internal power supply
E Connector for FlashKey
F Connector for external reset pushbutton
G Reset pushbutton
H Battery
I RJ45 connector for GSM200 module
L Jumpers for Telephone Line / GSM200 Module selection
M Built-in microphone
N Connector for built-in microphone
O Terminal blocks

Page 5 DESCRIPTION
Terminal blocks:
+ 12Vdc output (max. 100mA)
- Negative pole
AI Given alarm indicator light
AR Received alarm indicator light
+12 12Vdc output (max. 100mA)
C Common terminal for inputs AL1 and IN1
- Negative pole
AL1 Alarm input 1
AL2 Alarm input 2
IN1 Filter input
ALT2 Output for connecting loudspeaker of passive handsfree
terminal
MIC2 Input for connecting microphone of passive handsfree or
single microphone
MIC3 Input for connecting microphone of passive handsfree or
single microphone
- Negative pole
TEL Local telephone
RL1 Relay
Ground terminal for telephone line
LTI Telephone line input
- Negative pole
V + Pit active handsfree
P Alarm pushbutton
Q LEDs indicating device operation and GSM200 signal
strength
R End alarm pushbutton (Reset pushbutton)

DESCRIPTION Page 6
ST61
A Connector for built-in loudspeaker
B LED indicating device operation (red)
LED indicating GSM200 signal strength (green)
C Built-in loudspeaker
D Connector for Esse-ti power supply (12Vdc)
E Connector for FlashKey
F Reset pushbutton
G RJ45 connector for GSM200 module
H Jumpers for Telephone Line / GSM200 Module selection
I Built-in microphone
L Connector for built-in microphone
M Terminal blocks

Page 7 DESCRIPTION
Terminal blocks:
+ 12Vdc power supply input or 12Vdc output (max. 100mA,
if present Esse-ti power supply)
- Negative pole
AI Given alarm indicator light
AR Received alarm indicator light
+12 12Vdc output (max. 100mA)
C Common terminal for inputs AL1 and IN1
- Negative pole
AL1 Alarm input 1
AL2 Alarm input 2
IN1 Filter input
ALT2 Output for connecting loudspeaker of passive handsfree
terminal
MIC2 Input for connecting microphone of passive handsfree or
single microphone
MIC3 Input for connecting microphone of passive handsfree or
single microphone
- Negative pole
TEL Local Telephone
RL1 Relay
Ground terminal for telephone line
LTI Telephone line input
- Negative pole
V + Pit active handsfree

CONNECTING THE TELEPHONE LINE Page 8
CONNECTING THE TELEPHONE LINE
HELPY QUICK –ST61
The device allows the connection of a PSTN line or GSM line by means of the
GSM200 module or a traditional GSM interface.
PSTN line or traditional GSM interface
 Connect the ground terminal (indicated by ) to a ground socket in order
to increase the telephone line protection.
 Make sure that Jumpers (G in the picture at page 2 or H in the picture at
page 6) are set in the position shown below (default setting).
 Connect the telephone line to the LTI.
GSM200 Module
 Please see also the GSM200 User Manual.
 Make sure that Jumpers (G in the picture at page 2 or H in the picture at
page 6) are set in the position shown below.
 Connect the RJ45 connector (F in the picture at page 2 or G in the picture at
page 6) to the GSM200 module by means of the supplied cable.

Page 9 CONNECTING THE TELEPHONE LINE
HELPY QUICK-TL
The device allows the connection of a PSTN line or GSM line by means of the
GSM200 module or a traditional GSM interface.
PSTN line or traditional GSM interface
 Connect the ground terminal (indicated by ) to a ground socket in order
to increase the telephone line protection.
 Make sure that Jumpers (L in the picture at page 4) are set in the position
shown below (default setting).
 Connect the telephone line to the LTI.
GSM200 Module
 Please see also the GSM200 User Manual.
 Make sure that Jumpers (L in the picture at page 4) are set in the position
shown below.
 Connect the RJ45 connector (I in the picture at page 4) to the GSM200
module by means of the supplied cable.

CONNECTING EMERGENCY PUSHBUTTON AL1 AND FILTER IN1 Page 10
CONNECTING EMERGENCY
PUSHBUTTON AL1 AND FILTER IN1
HELPY QUICK-TL –ST61
It is possible to connect (inside the elevator car) voltage free contact
pushbuttons or powered pushbuttons.
Voltage free contact pushbuttons
Connect the filter contact to IN1 terminal and – (negative pole).

Page 11 CONNECTING EMERGENCY PUSHBUTTON AL1 AND FILTER IN1
Powered pushbuttons (12~ 24Vdc)
Connect the filter contact to IN1 terminal and – (negative pole).
Connect the filter contact to IN1 terminal and +12V terminal.

WIRING DIAGRAMS Page 12
WIRING DIAGRAMS
HELPY QUICK

Page 13 WIRING DIAGRAMS
HELPY QUICK-TL
Wiring diagram with active handsfree terminal in
the pit

WIRING DIAGRAMS Page 14
Wiring diagram with passive handsfree terminal
in the elevator car bottom

Page 15 WIRING DIAGRAMS
ST61
Wiring diagram with active handsfree terminal in
the pit

WIRING DIAGRAMS Page 16
Wiring diagram with passive handsfree terminal
in the elevator car bottom

Page 17 CORRECT OPERATION CHECKLIST
CORRECT OPERATION CHECKLIST
1. PROGRAMMING
 Access to programming: lift the local telephone handset and dial
.
You will hear the dialling tone (one longer tone followed by a shorter
tone).
 Only if GSM200 module is present: dial .
 Program a telephone number for the emergency-call alarm:
dial <telephone number> .
 Record the identification message of the specific elevator (max. 22
seconds), which is meant to contain all necessary information
concerning the elevator location: dial , pronounce the
message and hang up.
 To listen again to the previous message dial: .
 Make an external call to check the telephone line presence: dial and
digit the telephone number to make a test call.
2. ALARM PROCEDURE CHECK
 Press the emergency button.
The emergency call will be made.
3. ANSWERING AN ALARM
-1st mode: handsfree connection by “Handsfree activation” code (factory
default)
 Answer by the called party.
The voice messages will be heard.
 Press to speak with the trapped person.
-2nd mode: automatic handsfree connection
 Answer by the called party.
 Speak with the trapped person.
Remark: you can choose the 1st or the 2nd mode with the “Handsfree
connection mode” programming (code 78).

CORRECT OPERATION CHECKLIST Page 18
4. RESETTING AN ALARM
-1nd mode: reset by “End” code (factory default)
 Press to end the alarm.
-2st mode: automatic reset
 Hang up or press to end the alarm.
Remark: you can choose the 1st or the 2nd mode with the “Alarm
reset mode” programming (code 77).
In case it should not be possible to stop the alarm procedure remotely (i.e. the
entered telephone number is incorrect) simply lift the handset of the local telephone
and dial * <Password> # (by factory default: .
How to use the reset pushbuttons
Use of the reset pushbuttons (E in the picture at page 2, G in the picture at page
4, R in the picture at page 5, F in the picture at page 6):
 Pressing shortly
Allows to interrupt an alarm call.
By pressing shortly you get the same result as lifting the handset of the local
telephone and entering : * <Password> #.
 Pressing longer (15 seconds)
Allows to reset the device.
By pressing longer, the device will be re-started with no need to disconnect
the power supply.
The reset operation does not alert the previously set parameters.

Page 19 PROGRAMMING
PROGRAMMING
In the tables below:
 INST indicates that the programming procedure is allowed for the installer;
 OPER indicates that the programming procedure is allowed for the operator;
 factory default values are highlighted in bold.
Basic programming
BASIC PROGRAMMING
ACCESS TO
PROGRAMMING
<INSTALLER or OPERATOR PASSWORD>
(by default: )
EXITING THE
PROGRAMMING
<INSTALLER or OPERATOR PASSWORD>
(by default: )
TYPE OF
TELEPHONE
LINE
(INST)
PSTN line or traditional GSM interface
GSM200 module
TELEPHONE
NUMBERS
(INST)
(position
from 01
to 12)
SOURCE RECEIVER
…
(X…X =
telephone
number,
max 20
digits)
emergency-
call button ADEMCO
technological
alarms
USER
periodic
test call ESSE-TI
- CLI
alarm sent
alert
notification
SMS
(only with
GSM200)
alarm
terminated
alert
notification
P100

PROGRAMMING Page 20
BASIC PROGRAMMING
DELETING
TELEPHONE
NUMBER
(INST)
(position from
01 to 12)
HANDSFREE
CONNECTION
MODE
(INST)
handsfree activation by
“Handsfree activation” code
automatic handsfree activation
ALARM RESET
MODE
(INST)
automatic reset
alarm reset by “End” code
DATE
(INST)
WEEKDAY
(dd) (mm) (yy)
SUNDAY
MONDAY
TUESDAY
WEDNESDAY
THURSDAY
FRIDAY
SATURDAY
TIME
(INST)
(hhmm; from 0000 to 2359)
RECORD
MESSAGES
(INST)
identification message
(max. 22 sec.) (beep) record and
hang up
courtesy message
(max. 22 sec.)
LISTEN TO
MESSAGES
(INST/OPER)
identification message
(listen)
courtesy message
INSTALLATION
TYPE
(INST)
handsfree terminals only on the roof, in the
elevator car, in the bottom of the elevator car
active handsfree terminal also in the pit
DEAD BATTERY
ALARM
(INST)
disabled alarm
enabled alarm
NO MAINS
POWER SUPPLY
ALARM
(INST)
disabled alarm
from 01 to 99 = enabled alarm with XX minutes
delay