Essential Industries Hose-End User manual

Package Contents:
1. Injection molded assembly:
foaming barrel, handle, and eductor.
2. Concentrate container:
(1) - 96 oz., (1) - 48 oz.
3. Suction tube/strainer.
4. Spray gun with quick disconnect assembly.
5. Lt. Purple Ultra Lean tip installed in sprayer lid.
6. Product information sheet.
•WEAR protective clothing and eyewear when dispensing chemicals or other materials.
•ALWAYS observe safety and handling instructions of the chemical manufacturers.
•ALWAYS direct discharge away from you or other persons or into approved containers.
•ALWAYS dispense cleaners and chemicals in accordance with manufacturer's instructions. Exercise
CAUTION when maintaining your equipment.
•CLEAN equipment after each use in accordance with instruction sheet.
•WEAR protective clothing and eyewear when working in the vicinity of all chemicals, filling or emptying
equipment or changing metering tips.
•ALWAYS re-assemble equipment according to instruction procedures. Be sure all components are firmly
screwed or latched into position.
•ATTACH only to tap water outlets (85 PSI maximum).
Operating Instructions:
1. Unscrew foamer lid assembly from container.
2. Select a metering tip using the chart below as a guideline and press the tip firmly into the hose barb on the
bottom of the lid assembly. Install the suction tube on the hose barb.
3. Fill the container with concentrate. Screw foamer lid assembly securely onto container.
CAUTION: Foamer lid assembly must be securely fastened to container to prevent accidental spilling of
concentrate during use of foamer.
4. Insert foamer lid assembly into female quick connect on spray gun.
5. Connect a garden hose with 3/4" male garden hose thread to the base of the spray gun handle. Turn on the
water supply to the hose. (Minimum 25 PSI water pressure is required to operate the foamer.)
6. Grasp the spray gun handle in one hand and the foamer container in the other. Squeeze the spray gun
handle to begin foaming. Continuous operation can be achieved by usingthe handle lock provided on the
spray gun. Rinse by disconnecting the spray gun from the foaming lid assembly. To remove the foamer from
the spray gun, simply grasp the quick connect on the spray gun in one hand and the foamer assembly in the
other. Pull in opposite directions. (The outside collar around the quick connect will slide toward the spray gun,
disengaging the foamer barrel.)
SAFETY NOTE
PRODUCT DILUTION CHART
Hose-End Degreaser and Sanitizer System
Product Dilution Tip Color
Quick Suds #358 1:64 Yellow
1:32 Green
1:20 Beige
Food Service 1:28 Aqua
Degreaser #2258 1:96 Yellow
1:64 Brown
Foaming Restroom & 1:40 Green
Shower Cleaner #605 1:20 Beige
1:10 No Tip
Quat Rinse #2331 1:512 Lt. Purple

Troubleshooting Instructions:
Problem Cause Remedy
1.Unit does not draw a.Clogged suction tube strainer a. Clean or replace
concentrate b. Metering tip orificeobstructed b. Rinse tip or replace: Do not attempt
to clean: may alter size of orifice
c. Water pressure too low c. Minimum 25 PSI required
d. Mineral deposits in d. Back flush unit. Remove container,
barrel of foamer tube and metering tip. Put finger over
barrel suction opening. Apply minimal
water pressure through garden hose at
nozzle of barrel to be flushed.
d. Descale foamer by soaking in weak
descaling solution.
e. Clogged water inlet e. Clean or replace strainer.
strainer (low water flow)
2. Weak foaming action a. Clogged water inlet strainer a. Clean or replace.
b. Water pressure too low b. Minimum 25 PSI required
c. Water temperature too high c. Use lower temp water source. (Concentrate
flow decreases above 140º F water)
If above steps fail to produce good concentrate draw and/or foaming action, replace lid assembly. See
component chart below.
KEY PART NO. DESCRIPTION
110083713 Spray gun & quick disconnect
2a 10061501 Foamer lid assembly
b10061502 Sprayer lid assembly
3688201 Concentrate container - 96 oz.
688202 Concentrate container - 48 oz.
410027001 Lt. Purple ultra lean metering tip
5500808 Suction tube, 8"
6609600 Foot strainer
PARTS LIST
1
2a
4
52a
6
3
4
P.O. Box 12 • Merton, WI 53056
1-800-551-9679 • www.essind.com