Essentials 5543J User manual

PIR Coach Lantern
5543J
27/08/2015
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
Recycling advice
Safety information
Do not use solvents or abrasive cleaners as these could damage the finish.
Glass - Remove and wash in warm water or just use a damp cloth. Do not use abrasive materials.
Do not clean the units with a pressure washer.
This bulb is protected by a shade. This part must be replaced immediately should the shade
become cracked or damaged. This fitting must not be used without the shade in place.
Care and cleaning
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Fitting/replacing bulbs
When changing a bulb, always switch off at the mains and allow the bulb to cool before handling.
Dispose of used bulbs carefully.
Do not exceed the wattage stated from that indicated on the fitting.
To access the bulb, remove the decorative nuts on top of the shade, and lift off the top. Set aside.
Relocate the shade top over the screws and secure in place with the screws.
Replace Cracked
Shade
Please note this product is fitted with
a daylight sensor, therefore it will only
activate once the ambient light level
drops below 10 Lux.
Duration the bulb stays on is
adjustable by turning ‘Time’ screw
Detection range can be adjusted
by turning ‘Sens’ screw
Base of productAdjustable 6 - 12 metres
TIME SENS
3m
6m
8m
12m
120˚

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified
electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
Always use the correct type and wattage bulb. Never exceed the wattage stated.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling. Dispose
of used bulbs carefully and responsibly.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
This product is rated at IP44.
This product is not suitable for location in or near a marine environment.
The entire unit gets hot whilst on for a period of time.
Specification
Voltage: 240V 50Hz a.c.
Lamp: Max 42W E27 GLS
Lumens: 550lm
IP rating: 44
PIR load: Max 100W
Having correctly identified the wiring from your light fitting, connect to the terminal block in the following way:
Wiring
Installation
Existing fittings must be completely removed before installation of a
new product. Before removing the existing fitting, carefully note the
position of each set of wires.
• Remove mounting box (A) from product by removing dome nuts
(C) and washers (D). Carefully pierce a small hole in the rubber
gasket in the centre of the mounting box to allow the cable to pass
through.
• Thread the cable through the hole, ensuring the drain hole is at the
base of the mounting box.
• Use the mounting box as a template to mark and drill the holes in
the correct position.
• Fix the mounting box to the wall using the screws and plugs
supplied (B). Ensure the wall is capable of holding the weight of
the product. Take care to avoid damaging any concealed wiring and
pipes. The correct fixings should be used for brick or cavity walls.
• Seal the screw fixings to maintain the IP rating of the fitting.
Check that...
• You have correctly identified the
wires.
• The connections are tight.
• No loose strands have been left out
of the connection block.
NEUTRAL
EARTH
SWITCHED LIVE
BLUE (N)
BROWN (L)
GREEN/YELLOW
SUPPLY LIGHT FITTING
• Ensure that the cable is not snagged and seal the entry to maintain the IP rating of the product.
• Fit the product back on to the mounting box and refit washers (D) and dome nuts (C), tighten dome nuts to secure.
• Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Commissioning
PIR Adjustment
• The unit must be installed in a vertical position, and fitted 1.8m above the ground.
• The PIR sensor can be adjusted, allowing the detection distance to be altered to suit the location. The detection
angle is set at 120 degrees. The duration that the lamp stays on can also be altered from 5 seconds - 8 minutes.
Use a small screwdriver to adjust the ‘TIME’ and ‘SENS’ screws. When adjusting the sensitivity (detection
distance) in daylight it will be necessary to cover the sensor to simulate night time.