ETA Systems PD11LV User manual

OWNER’S MANUAL
OPERATION INSTRUCTIONS January 2006
1450 Lakeside Dr., Waukegan, IL 60085 USA
330-677-4424 • 800-321-6699 • Fax: [phone]
http://www.etasys.com E-mail [e-mail]
All designs and specifications are subject to change without notice. Copyright © 2004 ETA Systems.
1 Light Switch - activates rack illumination. Choose HI or LOW intensity
2 Light Tubes - illuminates up to 25 rack spaces or over 3 feet
3 Digital Voltmeter Readout - displays incoming line voltage
4 Circuit Breaker—resetable 15 amp thermal circuit breaker
5 Outlet Switch - lighted power switch activates protection and filtration to all black outlets and
front panel outlets
6 Front Panel Outlet - convenient, filtered, protected and switched outlet
7 Power Cord - Six foot heavy duty U-grounded 14-gauge power cord
8 Ivory Outlets - unswitched outlets with continuous power available. Circuit breaker protected.
9 Black Outlets - EMI/RFI filtered, spike/surge protected and switched outlets
PD11LV Operating Instructions:
1. Install in a standard 19” rack or free standing position.
2. Connect Power Distribution power cord (#7) into standard 120V wall outlet.
3. Plug sensitive electrical equipment into conditioned black outlets (#9) or (# 6).
4. Move outlet switch (#5) to “ON” position to provide power and protection to electrical equipment.
5. For illumination, pull out light tubes (#2) and move light switch (#1) to “HI” or “LOW” position.
IMPORTANT: Be sure light switch (#1) is in “OFF” position when light tubes are recessed.
6. Digital voltmeter readout (#3) is calibrated to nominal 117V at the factory. No adjustment necessary.
When calibration is required for special applications, an adjustable trimpot is located on the voltmeter
readout assembly.
WARNING: Removing top cover is necessary. Adjustment must be done by a qualified individual.
7. Digital voltmeter readout (#3) automatically displays incoming voltage when power cord (#7) is con-
nected. If you wish to have digital display on only when power switch is “ON”, move switch on voltmeter
display assembly inside unit to “OFF” position. WARNING: Removing top cover is necessary. Adjustment
must be done by a qualified individual.
6MAN-005

All designs and specifications are subject to change without notice. Copyright © 2004 ETA Systems.
PD11LV SPECIFICATIONS:
Dimensions 19" L x 7 1/2" D x 1 3/4" H
Weight 7 lbs. (less packaging)
Housing Quality Black powder coated chassis
Electrical 120V, 50/60 Hz, single phase
Max. amps 15/unit
Max. watts 1800/unit
Spike/surge protection Line to neutral, neutral to ground,
line to ground
Response time < 1 nanosecond
Max. clamping voltage 330V
Max. spike current 6500 amps
Max. surge energy 630 joules total
Noise filter (EMI/RFI) Frequency 150 kHz -200 MHz
Attenuation up to 20 dB
Certification ETL Listed
PD11LV FEATURES
• 10 protected U-grounded power out-
lets,
8 switched, 2 "always on"
• Four dual 15 amp U-grounded outlets
• One "always on" dual 15 amp U-
grounded outlet on back
panel
• Full 15 amps, 1800 watts capacity
per unit
• Protected "always on" 15 amp AC
power outlet on the
front panel
• Total unit 15 amp circuit breakers
located on front panel
• Digital voltmeter readout
• Dual swivel rack high output illumina-
tors with High/Low
settings and easy-to-change bulb ac-
cessibility
• Spike and surge protection
• EMI/RFI filtration
• 1 rack space
• 3 year limited warranty
Typical Uses
All Professional Permanent Installa-
tions, Recording Studios, Theatres,
Schools, Clubs, Churches, any enter-
tainment venue, business board
rooms, and audio/visual multi-use
presentation rooms.
Portable Applications: On-The-Road
Concert Tours, Bands, and D.J. ser-
vices.
Other Important Applications: A/V
racks, computer networks, and home
entertainment centers.
• “Always-On” Protected Outlets
• 10 Rear Panel Outlets
• Front Panel Convenience Outlets
• Digital Voltmeter Display Readouts
• Microprocessor Managed Voltage Regulators
• Programmable and Linkable Sequential Turn-on Models
• Models Adaptable for Multiple AC Adapters
• High Amp Conditioned Models
• Easy Bulb Change Feature
Standard on Every ETA
Power Conditioning Model
• Spike and Surge Protection and EMI/RFI Filtration on
All Three Legs of the Incoming AC Power—A Must, to
Ensure Protection of Electronic Components and Equip-
ment.
Thank you for choosing
ETA Systems Power Distribution
Drawing upon our 20 years of solving
high-amperage lighting needs and listening
to customers’ concerns, we have developed a
most extensive line of Audio Conditioned
Power Distribution. As the problems inherent
with AC power increase, you will find ETA
providing solutions.
Call 1-800-321-6699 for a Full Line
Brochure
6MAN-005